JVC KM-H3000U, KM-H2500 manual Next Transition Key Behavior, To set the transition resume direction

Page 22

To set the transition resume direction:

1

4

 

2 3

1.Press MENU.

2.Press the PERS Wipe Pattern button.

3.Press NEXT until Resume is displayed.

4.Use the Resume knob to set the transition direction used when a paused transition is re-started. You can choose from the following:

•Fwd — The transition completes as originally set.

•Rev — The transition reverses and the switcher returns to the on-air state it was in before the transition was started.

Next Transition Key Behavior

You can choose whether a Key remains in the Next Transition area or is removed if a dedicated key transition is performed.

To set the Next Transition Key behavior:

1

4

 

2 3

1.Press MENU.

2.Press the PERS Wipe Pattern button.

3.Press NEXT until ARKey is displayed.

4.Use the ARKey knob to set whether a Key remains or is removed from the Next transition area after a dedicated key transition is performed. You can choose from the following:

•Off — The Key is removed from the Next Transition area after a dedicated key transition is performed.

•On — The Key remains active in the Next Transition area after a dedicated key transition is performed.

16

Page 21 Page 23
Image 22
Page 21 Page 23
Contents KM-H2500E/U KM-H3000E/U Important Regulatory and Safety Notices Safety Precautions Environmental Information Contents Introduction Advanced Operation Page Abbreviations About This ManualDocumentation Terms Control Panel OverviewMenu System To access a menu using the Menu buttonControl Panel Rear Connections Overview Knobs Installing Your Own Insert FilmsMenu Navigation ButtonsTransitions ShiftFader PositionerEuropean Video Formats Switcher Video FormatReference Type North American Video FormatsAssigning Fcfs Channels To assign an Fcfs channelFormat Conversions for Input Mode Format Conversions for Bus ModeOutput Reference Sync Setting the Output Reference SyncTo set the output reference sync Aspect Ratio Resetting the Output Reference SyncAncillary Data Output Configuration Input BNC ConfigurationDefault Alpha Channel Mappings To configure a Dhcp IP address for your switcher Clean FeedTo configure the Clean Feed output IP AddressAux Bus Memory Recalls Switcher PersonalityCustomizing the Panel Glow Saving Color Schemes Power-Save ModeLoading Color Schemes Double-Press Rate Transition Rate UnitsResource Sharing Editor Control Switch on Field or FrameNext Transition Area Reset Transition Resume DirectionTo set the transition resume direction Next Transition Key BehaviorTo set the Next Transition Key behavior To perform a transition Transition OverviewCutting on the Program Bus KEYWipe Transitions Configuring the Auto Trans RatePausing a Transition Keying OverviewSelecting Keys Video LayeringKey Transitions Performing Key TransitionsDedicated Key Transitions Setting the Transition Rate for Dedicated Key TransitionsChroma Key Mattes Using a MatteUsing other Adjustments Selecting a Matte ColorFade to Black To apply other adjustmentsTo fade to black Storing Memory Registers Using the Memory SystemChoosing a Memory Access Mode Recalling Memory RegistersMemory AI and Keys Bus HoldMemory AI and Recall to Preview Memory AI and Recall to Preview ExamplesRecall to Preview On To set the Recall to Preview modeTransition Limit Memory AITo Quickly Reset the Transition Limit Reset OptionsConfiguring Default Settings To configure user-defined defaultsResetting Individual Settings Restoring Default Settings to Factory StateResetting the Switcher Shared ParametersUSB Storage Resetting Menu ItemsRestoring to Factory Defaults Saving Memory Banks and RegistersPress Next until Run Software Upgrade From USB is displayed Software UpgradesTo upgrade the switcher software Loading Memory Banks and RegistersAdvanced Keying Completing a Software UpgradeModifying Keys Chroma Key Fine Tuning Split Keys Modifying Split KeysTo modify the appearance of a Split Key Aux Buses Accessing the Aux BusesModifying Wipes To modify time and directionTallies Selecting a Source for the Aux BusesSupported Editors General Purpose Interface GPIEditor Port Pin TriggerPage Transparency Media-Store OverviewFile Formats Loading an Image or Animation by BrowsingLoading an Image or Animation by Media Number Understanding Media NumbersEntering Media Numbers To lock or unlock place and bank valuesTo modify the position of a Media-Store image Modifying Media-Store Image AttributesTo change an image between shaped and unshaped Animation Control Modifying Animation PlaybackSaving and Reverting Attributes To save attributes for an image To revert to saved attribute valuesPage Power Requirements DimensionsWeight HD-SDI Input and Output SpecificationsSwitcher Error Messages Error MessagesGVG100 Protocol Supported Commands GVG100 Supported CommandsLast 5 bits used bit 0 is Name MLE/Keyer Byte Code GVG100 Supported Analog ControlsGVG100 Supported Lamps GVG100 Supported Buttons GVG100 Supported Buttons Page 多格式数字高清切换台

KM-H2500, KM-H2500U, KM-H3000U, KM-H2500E, KM-H3000E specifications

The JVC KM-H3000E, KM-H2500E, KM-H3000U, KM-H2500U, and KM-H2500 are professional video production switchers designed to meet the demands of live broadcasting, events, and production environments. These switchers are renowned for their robust construction, intuitive operation, and advanced features that cater to a wide range of workflow requirements.

The KM-H3000E and KM-H3000U are high-end models, offering extensive capabilities for complex productions. Both units feature a 1 M/E switcher configuration, enabling seamless switching between multiple video sources. The KM-H3000 series supports HD and SD formats, ensuring compatibility with various input signals. One of its significant characteristics includes a large-scale multi-viewer output, which provides operators with the ability to monitor multiple sources on a single screen, enhancing the efficiency of live production.

In terms of connectivity, the KM-H3000 series equipped with extensive I/O options, allowing for flexible integration with other broadcast equipment. It also supports external keyers, picture-in-picture effects, and advanced chroma keying, creating dynamic live content that captivates audiences. Additionally, the user interface is designed for quick and intuitive operation, featuring customizable buttons and clear labeling that streamline the switching process.

On the other hand, the KM-H2500E and KM-H2500U serve as mid-range alternatives, suitable for smaller operations without compromising functionality. These models maintain a compact design while still offering an impressive array of features. The KM-H2500 series includes 1 M/E switcher capabilities and supports multiple HD/SD formats, similar to its higher-end counterpart, but with slightly reduced input options.

One notable feature of the KM-H2500 is its cost-effectiveness, making it an attractive choice for educational institutions, small production houses, and local broadcasters. It supports simple transitions, effects, and basic keying, enabling users to produce quality content without the complexity of more advanced systems.

In summary, JVC's KM-H series offers versatile solutions for video production, whether it's high-end broadcasting or smaller-scale operations. With their robust feature sets, ease of use, and flexible connectivity, the KM-H3000E, KM-H2500E, KM-H3000U, KM-H2500U, and KM-H2500 are exceptional choices for any production environment. These switchers exemplify JVC's commitment to quality and innovation in the realm of professional video equipment.
Top Page Image Contents