GVG100 Supported Buttons | JVC KM-H3000E, KM-H2500U, KM-H3000U

JVC KM-H3000E, KM-H2500U, KM-H3000U, KM-H2500E manual GVG100 Supported Buttons

Page 53

Table 8 GVG100 Supported Lamps

Name	MLE/Keyer	Byte Code	Notes
Positioner On	MLE	0x1C	Always on. Turning OFF results in a
Positioner On			protocol error.
			protocol error.

Reverse Wipe	MLE	0x1D

Dsk Preview	Keyer	0x1E	Always true. All Keyers show on Preview
Dsk Preview			Turning OFF results in a protocol error.
			Turning OFF results in a protocol error.

Fade To Black	—	0x1F

Key Bus 0-9	Keyer	0x20-0x29	Turning OFF results in a protocol error.

Key Bus On Air	Keyer	0x2A	Turning OFF results in a protocol error.

Key Video Fill	Keyer	0x2F	Always true. Turning OFF results in a
Key Video Fill			protocol error.
			protocol error.

Wipe Type	MLE	0x30-0x39	Turning OFF results in a protocol error.

Key Invert	Keyer	0x40	DSKs. Turning OFF results in a protocol
Key Invert			error.
			error.

Key Mask	Keyer	0x41	DSKs. Turning OFF results in a protocol
Key Mask			error.
			error.

Key Autokey	Keyer	0x42	DSKs. Turning OFF results in a protocol
Key Autokey			error.
			error.

Key Selfkey	Keyer	0x43	DSKs. Turning OFF results in a protocol
Key Selfkey			error.
			error.

Key Invert	Keyer	0x44	Turning OFF results in a protocol error.

Key Mask	Keyer	0x45	Turning OFF results in a protocol error.

Memory Mode Toggle	—	0x47	Toggles between memory and pattern
Memory Mode Toggle			modes.
			modes.

Next Trans Is Bkgd	—	0x48	Turning OFF results in a protocol error.

Next Trans Is Key 1	—	0x49	Turning OFF results in a protocol error.

Cut	MLE	0x4A	Turning OFF results in a protocol error.

Key Selfkey	Keyer	0x4C	Turning OFF results in a protocol error.

Key Autokey	Keyer	0x4D	Turning OFF results in a protocol error.

Key Chromakey	Keyer	0x4E	Turning OFF results in a protocol error.

Editor Enable	—	0x4F	Editor control is always enabled. Turning
Editor Enable			OFF results in a protocol error.
			OFF results in a protocol error.

Keyer Active	Keyer	0x52

Table 9 GVG100 Supported Buttons

Name	MLE/Keyer	Byte code	Notes
Program Bus 0-9	MLE	0x00-0x09

Autotrans	MLE	0x0B

Key Trans	Keyer	0x0C	DSKs

Key Cut	Keyer	0x0D	DSKs

Wipe Trans	MLE	0x0E

Dissolve Trans	MLE	0x0F

Preset Bus 0-9	MLE	0x10-0x19

Image 53

Contents

KM-H2500E/U KM-H3000E/U Important Regulatory and Safety Notices Safety Precautions Environmental Information Contents Introduction Advanced Operation Page Documentation Terms About This ManualAbbreviations Control Panel OverviewControl Panel Rear Connections Overview To access a menu using the Menu buttonMenu System Menu Navigation Installing Your Own Insert FilmsKnobs ButtonsFader ShiftTransitions PositionerReference Type Switcher Video FormatEuropean Video Formats North American Video FormatsTo assign an Fcfs channel Assigning Fcfs ChannelsFormat Conversions for Bus Mode Format Conversions for Input ModeTo set the output reference sync Setting the Output Reference SyncOutput Reference Sync Ancillary Data Resetting the Output Reference SyncAspect Ratio Default Alpha Channel Mappings Input BNC ConfigurationOutput Configuration To configure the Clean Feed output Clean FeedTo configure a Dhcp IP address for your switcher IP AddressCustomizing the Panel Glow Switcher PersonalityAux Bus Memory Recalls Loading Color Schemes Power-Save ModeSaving Color Schemes Resource Sharing Transition Rate UnitsDouble-Press Rate Next Transition Area Reset Switch on Field or FrameEditor Control Transition Resume DirectionTo set the Next Transition Key behavior Next Transition Key BehaviorTo set the transition resume direction Cutting on the Program Bus Transition OverviewTo perform a transition KEYPausing a Transition Configuring the Auto Trans RateWipe Transitions Keying OverviewKey Transitions Video LayeringSelecting Keys Performing Key TransitionsChroma Key Setting the Transition Rate for Dedicated Key TransitionsDedicated Key Transitions Using other Adjustments Using a MatteMattes Selecting a Matte ColorTo fade to black To apply other adjustmentsFade to Black Choosing a Memory Access Mode Using the Memory SystemStoring Memory Registers Recalling Memory RegistersMemory AI and Recall to Preview Bus HoldMemory AI and Keys Memory AI and Recall to Preview ExamplesTransition Limit To set the Recall to Preview modeRecall to Preview On Memory AIConfiguring Default Settings Reset OptionsTo Quickly Reset the Transition Limit To configure user-defined defaultsResetting the Switcher Restoring Default Settings to Factory StateResetting Individual Settings Shared ParametersRestoring to Factory Defaults Resetting Menu ItemsUSB Storage Saving Memory Banks and RegistersTo upgrade the switcher software Software UpgradesPress Next until Run Software Upgrade From USB is displayed Loading Memory Banks and RegistersModifying Keys Completing a Software UpgradeAdvanced Keying Chroma Key Fine Tuning To modify the appearance of a Split Key Modifying Split KeysSplit Keys Modifying Wipes Accessing the Aux BusesAux Buses To modify time and directionSelecting a Source for the Aux Buses TalliesEditor Port General Purpose Interface GPISupported Editors Pin TriggerPage File Formats Media-Store OverviewTransparency Loading an Image or Animation by BrowsingEntering Media Numbers Understanding Media NumbersLoading an Image or Animation by Media Number To lock or unlock place and bank valuesTo change an image between shaped and unshaped Modifying Media-Store Image AttributesTo modify the position of a Media-Store image Saving and Reverting Attributes Modifying Animation PlaybackAnimation Control To revert to saved attribute values To save attributes for an imagePage Weight Dimensions Power Requirements HD-SDI Input and Output SpecificationsGVG100 Protocol Supported Commands Error MessagesSwitcher Error Messages GVG100 Supported CommandsLast 5 bits used bit 0 is GVG100 Supported Lamps GVG100 Supported Analog ControlsName MLE/Keyer Byte Code GVG100 Supported Buttons GVG100 Supported Buttons Page 多格式数字高清切换台

JVC KM-H3000E, KM-H2500U, KM-H3000U, KM-H2500E manual GVG100 Supported Buttons

Table 8 GVG100 Supported Lamps

Name

Table 9 GVG100 Supported Buttons

Name