Pioneer DJM-5000 operating instructions Operating the DJ section

Page 13

Operating the DJ section

Outputting sound

1 Press [POWER]

Turn on the power of this unit.

2 Set the input selector switch

Select the input source of each channel from the components connected to this unit.

!To output sound of the computer connected to the [USB] terminal, switch the input selector switch for [CH-2], [CH-3], and [CH-4] to [USB].

3 Rotate [TRIM]

Adjusts the level of audio signals input in each channel.

!The channel level indicator lights when the sound is being properly input to the channel.

4 Set the channel fader to the inner position

Adjusts the level of audio signals output in each channel.

5 Adjust the crossfader assign switch

Switches the output destination of each channel.

[A]: Assigns to [A] (left) of the crossfader.

[B]: Assigns to [B] (right) of the crossfader.

[THRU]: Assigns to the [MASTER] channel (the crossfader is not passed through).

6 Adjust the crossfader curve switch ([CROSS FADER])

Switches the crossfader curve characteristics.

[]: Makes a sharply increasing curve (if the crossfader is moved away from the [A] side, audio signals are immediately output from the [B] side).

[]: Makes a curve shaped between the two curves above and below.

[]: Makes a gradually increasing curve (if the crossfader is moved away from the [A] side, the sound on the [B] side gradually increases, while the sound on the [A] gradually decreases).

7 Set the crossfader

Outputs audio signals assigned by the crossfader assign switch corresponding to the curve characteristics selected by [CROSS FADER] (Crossfader Curve Selector Switch).

!You do not need to follow this step when the crossfader assign switch is set to [THRU].

8 Rotate [LEVEL] for the [MASTER] channel

The sound is output from [MASTER1] and [MASTER2]. The master level indicator lights.

Adjusting the sound quality

Rotate [HI], [MID] or [LOW] in each channel

Refer to Specifications on page 18 for the range of sound that can be adjusted by each control.

Monitoring sound with headphones

1Connect headphones to the [PHONES] jack

2Press [CUE] for the channel to be monitored

The button lights up brightly in orange.

3 Turn the [LEVEL] dial for [HEAD PHONES]

Sound is output from the headphones in the channel selected by [CUE].

!Sound output from the headphones varies according to the combination of channels selected by [CUE]. See the table below.

CH-1

 

 

Headphone Output

 

CH-4

MASTER

ZONE

L channel

R channel

 

 

 

 

 

 

 

 

ON

OFF

OFF

CH (L)

CH (R)

OFF

ON

OFF

MASTER (L)

MASTER (R)

OFF

OFF

ON

ZONE (L)

ZONE (R)

ON

ON

OFF

CH (MONO)

MASTER (MONO)

ON

OFF

ON

CH (MONO)

ZONE (MONO)

OFF

ON

ON

MASTER (L)+ZONE (L)

MASTER (R)+ZONE (R)

ON

ON

ON

CH (MONO)

MASTER (MONO)

+ZONE (MONO)

 

 

 

 

!Monitoring is canceled if you press [CUE] again. The button lights up dimly in orange.

Using the fader to play a Pioneer DJ player (fader start)

If you connect a Pioneer DJ player using a control cable (supplied with a DJ player), you can start playback of control other operations of the DJ player with the fader of this unit.

The fader start feature is available only when a Pioneer DJ player is connected to [CH-1] or [CH-2].

Connect a Pioneer DJ player to this unit in advance (page 7).

Start playback using the channel fader

1Set the crossfader assign switch to [THRU]

2Press [FADER START]

Turn on the fader start function. The button lights up brightly in orange.

3Set the channel fader to the outermost position

4Set the cue on the DJ player

The DJ player pauses playback at the cue point.

5 Set the channel fader to the inner position

Playback starts on the DJ player.

!If you set the channel fader back to the original position, the player instanta- neously returns to the cue point already set and pauses playback (back cue).

Start playback using the crossfader

1Set the crossfader assign switch to [A] or [B]

2Press [FADER START]

Turn on the fader start function. The button lights up brightly in orange.

3 Set the crossfader

Set to the farmost end in the opposite direction to the channel to be fader started.

4 Set the cue on the DJ player

The DJ player pauses playback at the cue point.

5 Set the crossfader

Playback starts on the DJ player.

!If you set the crossfader back to the original position, the player instanta- neously returns to the cue point already set and pauses playback (back cue).

Operating the DJ software

The DJM-5000 also outputs the operating data for the buttons and dials in MIDI format. If you connect a computer with a built-in MIDI-compatible DJ software via a USB cable, you can operate the DJ software on this unit.

Install the DJ software on your computer in advance. Also, adjust audio and MIDI settings for the DJ software.

1 Connect the USB port on this unit to your computer

For details about connections, see Connecting a computer on page 8.

2Start the DJ software

3Set [MIDI] to [ON]

Transmission of the MIDI messages begin.

!You can send MIDI messages altogether according to the position of buttons, faders, or control knobs (snapshot).

!Adjust faders and control knobs to transmit messages based on the corre- sponding position. For details about the messages generated by this unit, see List of MIDI Messages on page 11.

4 Set [MIDI] to [OFF]

The MIDI messages are not transmitted even if you operate this unit.

English

En 13

Image 13
Contents DJM-5000 Information to User For Taiwan exclusively Contents Before start FeaturesWhat’s in the box Rear Panel ConnectionsConnecting output terminals Connecting input terminalsConnecting a computer Connecting to the control panelAbout the USB audio driver software Software Use AgreementConnecting the DJM-5000 and computer Installing the driver software Adjusting the buffer size Windows About USB-MIDI channel setting Checking the version of the driver software Checking the latest information on the driver softwareMSB List of Midi MessagesControl Panel OperationsOperating the DJ section Using the microphone effect feature Using a microphoneUsing the talk-over feature Operating the MC sectionOperating the PA section Additional information TroubleshootingAbout the exemption clauses CUE Block DiagramGeneral SpecificationsAudio Section Input / Output terminalsPage Importante Para uso exclusivo en Taiwán Montaje en una estantería según las normas EIA ContenidoCaracterísticas Antes de empezar a usar la unidadContenido de la caja Panel trasero ConexionesConexión de terminales de salida Conexión de terminales de entradaConexión a un ordenador Conexión al panel de controlAcerca del software de controlador de audio USB Contrato de Uso del SoftwareInstalación del software controlador Cuidados para la instalaciónConexión del DJM-5000 y un ordenador Ajuste del tamaño de la memoria intermedia Windows Acerca del ajuste del canal USB-MIDIVerificación de la versión del software controlador Lista de mensajes Midi Panel de control OperacionesSalida de sonido Operación de la sección DJAjuste de la calidad del sonido Monitoreo de sonido con auricularesUso de un micrófono Operación de la sección MCUso de la función de efecto del micrófono Uso de la función talk-overOperación de la sección PA Información adicional Solución de problemasAcerca de las cláusulas de exención Español Diagrama en bloquesGenerales EspecificacionesSección de audio Page 線路電壓選擇開關 使用前 安裝符合 EIA 標準的機架使用前 後面板 連接輸出端子 連接輸入端子連接至電腦 連接至控制面板關於 USB 音訊驅動程式軟體 按兩下 DJM-5000MX.X.X.dmg 按下 Power按兩下 DJM-5000AudioDriver.pkg 按兩下 DJM-5000X.XXX.exeMaster 頻道中按下 CUE 同時按住 CH-1與 CH-2的 Fader START,然後再按下 PowerMidi 訊息清單 控制面板 旋轉 Trim 操作 DJ 部分旋轉 Master 頻道的 Level 按下 Fader Start操作 MC 部分 操作 PA 部分 關於免責條款 故障排除區塊圖 本產品規格及設計如有變更,恕不另行通知。 日本先鋒公司出版。版權 2009日本先鋒公司。版權所有。 Printed
Related manuals
Manual 37 pages 2.89 Kb