Kramer Electronics Revision 6 manual Auxiliary Device View

Page 20

Defining the Control Room

Figure 12: The Auxiliary Device View

4.In the Control Room area, select 1 - SV-5521.

5.Click +.

6.Select a device from the list (for example, the RC-4remote control transmitter, see Section 4.1.2).

The RC-4(when selected in the Control Room area) appears in the Device View area of the Front Panel tab).

Figure 13: The Remote Control Device View

To add additional auxiliary devices (depending on the Master RC selected, up to four Aux K- NET devices and two Virtual Devices can be used in the same control setup, see Table 4), repeat the above steps

If the definition of the Control Room does not match the actual connected control room, the following warning appears:

Figure 14: Configuration Mismatch Warning

1 It is necessary to select the Master controller to add an additional device

13

Image 20

Contents Kramer K-Config Guide Revision Contents Figures Setting the LCD and Button Label Names Move the Stop Timer Action Set the New Command Table Name Tables Applicable Room Controllers IntroductionApplicable Room Controllers Available Commands for Room Control Ports Room Controller Commands AvailableTrigger Types Available Available Triggers for Room ControllersRoom Controller Devices Limitation How to Save a ProjectActions, Labels and Button Number Limits To configure your Room Controller, follow these basic steps Quick StartGlossary Initial PlanningGlossary Kramer K-Config Software Installation Installing the .NET Framework Revision 2.0 SoftwareInstalling the USB Driver Defining the SystemSelect or create a new working directory3 see Figure Installing Kramer K-Config SoftwareClick OK Following window appears see Figure Peripheral Device Drivers Downloading the DriversImporting xml Templates Importing the DriversDriver Manager Window Prior to Installing the Drivers Importing the Driver FilesDefining the Control Room Loading the DriversAdding the Master Device Auxiliary Device View Special Auxiliary Devices Device OperationsBasic Virtual Device Front Panel Custom Virtual Device Appearance in K-Config Virtual Device appears in the Front Panel area see FigureRight click the label and buttons to name them see Figure DVD Control Virtual Device Front PanelRC-4 Remote Controller Tab Area Settings Defining the Port ManagerDrivers Tree Window Selecting a DriverWriting a Port Description Defining the Ethernet Ports Select the Edid file to upload and click Open Edid file is uploadedDevice Settings Tab Connect Dialog BoxDevice Settings Tab Features DSTSummarizes date and time setting options Setting the Date and TimeWeb Settings Tab Web Settings WindowTriggers Built-in TriggersAdding Actions to a Trigger Select the desired port for example, RS-232.DTypeSelecting the Command Replacing an Action All On Trigger with actions assignedSelecting the Action to be replaced from the Action List Selecting a New ActionAdding a Custom Trigger Type the name of the custom trigger, and then click OKSet the Schedule Scheduling WindowMonitor Event Trigger Add actions to the trigger see SectionAdd Timer Trigger Timer Trigger Flowchart Power on ExampleTimer Trigger in the Triggers List Set the TimeoutProjector Power on Command in the Button Trigger Action List Selecting the Timer Start/Stop ActionStep III Define the Monitor Event System Inactivity Example Set the timeout to 20 minutes1 Add the following actions2 see SectionAdd the Stop Timer trigger Add the Start Timer triggerGPI/O Trigger Add GPI/O Trigger ButtonDigital Input Select the condition for activating the trigger Add actions to the new trigger see FigureSelect the trigger behavior GPI/O Defined as Digital OutputButton Trigger Select the Behavior of the Digital Input TriggerButton Trigger Properties Window Select the Button BehaviorButton Trigger Properties Window Toggle Toggle Number in the Action ListKnob Turning Trigger Action TypeShows the port command actions1 Shows the available button ignore states Button Color SelectionSwitcher Command Action Type Shows the unlock PIN code Select LEDs to Light Definition of 4 StatesSetting the State Action List States Action TypeDelay Action Type Write the Configuration Click Yes to write the configuration to the deviceClick OK to set the ID number Click OK to connect Setting K-NET ID window appearsSet K-NET IDs Driver Manager Window Driver Manager Window Features Driver ManagerCreating a Driver Command New Serial Command WindowWrite the serial command1, as illustrated in Figure Writing a Serial CommandCreating an IR Command New IR Command Window Creating Serial Range Commands Click OK Click the Table Details buttonSetting the Number of Command Rows Writing the Commands Logarithmic Row Selection Adding Actions to a Trigger via the Command Table Setting a Specific Volume LevelAdd the Command table to the list Adding the Commands Table to the ListSelecting commands 0 to Selecting commands in the Port Command Area Defining QueriesFeature Function Query Format DetailsLamp Hour Query Response Formats Query Details WindowWriting the Query Command Lamp Hours Projector Query Response Lamp HoursShows the query format details Lamp Hour Query Format DetailsPower Query Response Formats Writing the Query Command PowerProjector Query Response Power Query Format tab, set the query format, see FigureExpected Result Table Power Kramer K-Config Menus This section describes the Kramer K-ConfigmenusFile Menu Features File MenuSaving a Project Select Virtual Device to Save Export Device xml FileDevice Menu Features Device MenuLoad Firmware Upgrade Window SV-551 Connect WindowHelp Menu Features Help MenuConnecting via the Ethernet Local Area Connection Properties Window