Fostex LM16 manual Connecting the power cord, Preparation of power supply

Page 15

Model LM16 [Before using the unit]

Preparation of power supply

Connecting the power cord

Using the supplied power cord, con- nect the [AC IN] connector on the rear panel of the main unit and the AC outlet.

<Note>: Use only the supplied power cord.

	INPUT
AUX SEND (-2dBu)	INSERT	INSERT	INSERT	INSERT	INSERT	INSERT	INSERT	INSERT
MIDI OUT		CONTROLLER
				PHANTOM	POWER

AC outlet

Turning on the power

Press down the [POWER] switch on the rear panel of the main unit to turn on the power.

		INPUT
EFF SEND (-2dBu)	AUX SEND (-2dBu)	INSERT	INSERT	INSERT	INSERT	INSERT	INSERT	INSERT	INSERT
USB	MIDI OUT		CONTROLLER
					PHANTOM	POWER

[POWER] switch

To turn on or off the LM16 and peripheral devices which are connected to the LM16, follow the proper procedures described below.

Procedures of turning on the power after connecting peripheral devices

<Note>: Before turning on or off the LM16 and peripheral devices which are connected to the LM16, make sure that the channel faders and monitor gain control of the LM16, as well as the volume control of an monitor amplifier (or powered monitor speaker), are set to minimum. Otherwise, a loud sound may be produced suddenly that may damage the speaker or your hearing.

(1)Turn on the devices connected to the [INPUT] connectors to the LM16.

(2)Turn on the LM16.

(3)Turn on the monitor amplifier (or powered monitor speaker).

Procedures of turning off the power after connecting peripheral devices

(1)Turn off the monitor amplifier (or powered monitor speaker).

(2)Turn off the LM16.

(3)Turn off the devices connected to the [INPUT] connectors to the LM16.

15

Image 15

Contents

Model LM16 Safety Instructions Important Safety Instructions Table of contents Adjusting the input level Low-cut filter Limiter Equalizer Signal flow of the mixer Connecting sourcesUpgrading the software Introduction About power supplyPrecautions on installation About version upgradeAbout CAT-5 cable Cleaning the exteriorCondensation About damageOverview Main features Unpacking the carton Before using the unitMounting the main unit and control unit on the rack Setting the main unit and control unit separatelyUsage examples of LM16 Integrating the main unit and control unitNecessary items Integrating the control unit and main unitRack mount adaptor After attaching the adaptor Preparation of power supply Connecting the power cordConnection example live stage Connection to external devicesMTR Connection example home recordingBalanced Balanced and unbalanced inputs/outputsNames and functions Control unit input channel 1 through Solo switch POST/PRE switchMute switch 14 ST/1-2/3-4 assign switchesControl unit Master channel SUB in jacks / SUB in controlMonitor section Phantom 1-8, 9-16 indicators Internal effects sectionControl section Output Limiter switch AUX Send controls / Solo switches24 27 EFF Send control / Solo switch Assign to Stereo OUT switchesMain unit rear panel Control unit rear panelStereo OUT L, R connectors Phantom 1-8, 9-16 switchesController connector Group OUT 1, 2, 3, 4 connectorsMixer basics Signal flow of the mixerPhantom power supply setting Connecting sourcesAdjusting the input level Connecting sources to the input connectorsLimiter Gain adjustment while monitoringEqualizer Low-cut filterPost-fader Using an external effect processorUsing AUX 1, 2 Pre-faderUsing the internal effects processor Using InsertApplying the internal effects About the effect types MonitoringSolo monitor Channel groupingUsing SUB Set the Source switches on channels 15 and 16 to TRKSet the ST assign switches on channels 15 and 16 to on Block diagram Showing version information Showing date informationR meters between 7 R peak indicatorsInputs/Outputs SpecificationsMain unit Physical dimensionsPower Consumption approx W GeneralMMC Command List Model LM16 Midi Implementation ChartDeclaration of EC Directive Forthe US Customers only Fostex America Limited Warranty Shipping Effect processor IndexMemo Page Fostex CO