Fostex LM16 manual Specifications, Inputs/Outputs

Page 38

Model LM16 [Specifications]

Specifications

Inputs/Outputs

0dBV = 1.0 Vrms, 0dBu = 0.775 Vrms Reference level: -20dBfs

Input and Output (Main unit)

[MIC INPUT (1 - 16)]

Connectors:

XLR3-31, balanced

 

(combo)

Nominal input level:

-60dBu ~ -12dBu

Input impedance:

more than 1.5kΩ

Phantom Power:

P48V (1-8ch & 9-16ch

 

switchable, on/off)

[STEREO MIX OUT (L, R)]

Connectors:

RCA, unbalanced

Reference output level:-10dBu

Load impedance:

more than 10kΩ

[USB (HOST)]

 

Device:

USB2.0 Hi-speed for

 

storage connection

Connector:

A type

[MIDI OUT]

 

Connector:

DIN 5-pin

[TO CONTROL BOX]

 

Connector:

RJ45 (CAT-5, straight)

[LINE INPUT (1 - 16)]

Connectors:

ø6.3mm TRS phone,

 

balanced (combo)

Nominal input level:

-40dBu ~ +8dBu

Input impedance:

more than 10kΩ

[INSERT (1 - 8)]

 

Connectors:

ø6.3mm TRS phone,

 

(Tip: Output, Ring: Input)

Load impedance:

more than 10kΩ

Nominal output level: -10dBV

Input impedance:

more than 10kΩ

Nominal input level:

-10dBV

[STEREO BUS OUT (L, R)]

Connectors:

XLR3-31, balanced

Reference output level:+4dBu

Load impedance:

more than 10kΩ

[GROUP BUS OUT (1 - 4)]

Connectors:

ø6.3mm TRS phone,

 

balanced

Reference output level:+4dBu

Load impedance:

more than 10kΩ

[AUX SEND (1 - 3)]

 

Connectors:

ø6.3mm phone,

 

unbalanced

Reference output level:-2dBu

Load impedance:

more than 10kΩ

[EFFECT SEND]

 

Connector:

ø6.3mm phone,

 

unbalanced

Reference output level:-2dBu

Load impedance:

more than 10kΩ

Input and Output (Control unit)

[PHONES]

Connector:

ø6.3mm Stereo Phone

Load impedance:

more than 32Ω

[MONITOR OUT (L, R)]

 

Connector:

ø6.3mm Phone,

 

unbalanced

Reference output level:-12dBV

Load impedance:

more than 32Ω

[SUB IN (L, R)]

 

Connector:

RCA, unbalanced

Reference input level: -10dBV

Input impedance:

more than 10kΩ

[TO I/O BOX]

 

Connector:

RJ45 (CAT-5, straight)

Others

Frequency response: 20Hz - 20kHz +1dB, -2dB (44.1/48kHz)

S/N: Line (Trim Min) 103dB (Typical) Mic (Trim Max) 83dB (Typical)

Dynamic range: 103dB (Trim Min) (Typical)

T.H.D.: Mic (Trim Max) -> ST out: 0.01% (1kHz, -2dBFS) (Typical)

Line (Trim Min) -> ST out: 0.005% (1kHz, -2dBFS) (Typical)

Line (Trim Min) -> Phones: 0.1% or less (1kHz, 50mW, 32Ω)

38

Image 38
Contents Model LM16 Safety Instructions Important Safety Instructions Table of contents Signal flow of the mixer Connecting sources Adjusting the input level Low-cut filter Limiter EqualizerUpgrading the software About version upgrade About power supplyPrecautions on installation IntroductionAbout damage Cleaning the exteriorCondensation About CAT-5 cableOverview Main features Before using the unit Unpacking the cartonIntegrating the main unit and control unit Setting the main unit and control unit separatelyUsage examples of LM16 Mounting the main unit and control unit on the rackIntegrating the control unit and main unit Necessary itemsRack mount adaptor After attaching the adaptor Connecting the power cord Preparation of power supplyConnection to external devices Connection example live stageConnection example home recording MTRBalanced and unbalanced inputs/outputs BalancedNames and functions Control unit input channel 1 through 14 ST/1-2/3-4 assign switches POST/PRE switchMute switch Solo switchMonitor section Control unit Master channelSUB in jacks / SUB in control Control section Phantom 1-8, 9-16 indicatorsInternal effects section Assign to Stereo OUT switches AUX Send controls / Solo switches24 27 EFF Send control / Solo switch Output Limiter switchControl unit rear panel Main unit rear panelGroup OUT 1, 2, 3, 4 connectors Phantom 1-8, 9-16 switchesController connector Stereo OUT L, R connectorsSignal flow of the mixer Mixer basicsConnecting sources to the input connectors Connecting sourcesAdjusting the input level Phantom power supply settingLow-cut filter Gain adjustment while monitoringEqualizer LimiterPre-fader Using an external effect processorUsing AUX 1, 2 Post-faderApplying the internal effects Using the internal effects processorUsing Insert Monitoring About the effect typesChannel grouping Solo monitorSet the ST assign switches on channels 15 and 16 to on Using SUBSet the Source switches on channels 15 and 16 to TRK Block diagram Showing date information Showing version informationR peak indicators R meters between 7Specifications Inputs/OutputsGeneral Physical dimensionsPower Consumption approx W Main unitMMC Command List Midi Implementation Chart Model LM16Declaration of EC Directive Forthe US Customers only Fostex America Limited Warranty Shipping Index Effect processorMemo Page Fostex CO