Split CUE OFF, Split CUE on, Thru, Q9CROSSFADER

Q5Effect ON/OFF button

Sets the EFX effects to ON/OFF.

Q6Channel EFX SEND button

The various set effects can be obtained for the channel audio signal.

W4SPLIT CUE button

There are two headphone monitor modes.

SPLIT CUE OFF:

The cue signals and master signals can be monitored in stereo.

E5SOURCE SEL LN1/LN2/LN3/LN4/USB/P1–4 controls (channel input selector)

These enable any of six inputs to be selected for each of the channels. The same input can be selected for more than one channel.


	ENGLISH
R1MASTER BALANCE control		Getting
Adjusts the L/R balance of the MASTER output.
R2L/CUE, R/PGM master level meter
		Started
One of two modes can be selected for display
on this meter.

Multiple channels can be selected.

Q7Channel CUE buttons

Pressing in any or all of CUE buttons routes the respective source to the headphone and meter cue sections. When the CUE button is pressed multiple times, the channels selected by the CUE button are mixed.

•The SOLO mode with no signals mixed can also be selected as a preset.

Q8CROSSFADER ASSIGN switches

SPLIT CUE ON:

The monaural cue signals are heard through the left channel of the headphones, and the monaural master signals through the right channel.

W5CROSSFADER CONTOUR control

Allows adjusting the “shape” of the Crossfader response from a gentle curve for smooth, long running fades, to the steep pitch required for top performance cut and scratch effects.

LINE1

LINE2

LINE3

LINE4

USB 1/2 - 7/8

USB P1 - P4

SOURCE SEL

CH1

SOURCE SEL

CH4

	SPLIT CUE OFF:	Connections
	The master output audio level is displayed.
	SPLIT CUE ON:
	The right channel master CUE (monaural) and
	left channel CUE (monaural) audio levels are
	left channel CUE (monaural) audio levels are	Basic
	displayed.	Basic
	R3SIG/PK indicator	Operations
	This is the signal/peak meter for the mic input
	level.

A, B:

The channel source is assigned to A or B of the Crossfader.

THRU:

Select when you don’t assign the channel source into the Crossfader.

Q9CROSSFADER

Controls the relative output level from the summed A and B Mixes. When the fader is at its far left, only the A Mix is heard from the Outputs. As the fader is moved toward the right, the amount of B Mix is increased and the amount of A Mix is decreased. When the fader is centered, equal amounts of A and B Mixes are routed to the Outputs. Fully right is all B Mix at the Outputs.

W0Channel input fader (CH FADER)

Controls the level of the selected Input.

W1HEADPHONE output jack

Accepts 1/4” stereo headphone plugs.

W2HEADPHONE level control

Adjusts the volume for the headphones.

W3HEADPHONE PAN control

This is used to adjust the balance between the CUE sound and the master sound which are monitored using the headphones.

W6CH FADER CONTOUR control

Adjusts the volume curve response of the channel fader.

W7CH FADER START switch

This function will start the performance of CD/ Media Player with Ch. Fader automatically is

ON/OFF.

W8CROSSFADER START switches

Use this to switch the Crossfader Start function

ON and OFF.

W9MIC SEND LEVEL control

This is used to adjust the level at which the mic signals are sent to the master output.

E0Mic EFX INS button

This button enable the various effects to be obtained for the mic input signals.

E1MIC EQ controls

Adjusts the frequency of the mic input.

E2DUCKING ON/OFF button

•Use this to switch the Talk Over function ON and OFF. (ON/OFF is cyclic)

•When the button is lit, level of signals except Mics is attenuated.

•The ducking attenuation level can be adjusted in the “UTILITY” mode.

E3MIC1, MIC2 TRIM controls

Adjusts the level of the Main Mic input.

E4MIC1, 2 buttons

When the button’s LED is lighted, the mic signals take effect.

The desired USB source from USB P1–P4 can be selected from USB 1/2–7/8 and DVS from the utility mode preset control.

E6CD/PHONO line input selector buttons

These enable the line input of each channel to be selected as CD or PHONO.

CD:

Rear panel LINE1–4 CD terminal input

PHONO:

Rear panel LINE2–4 PHONO terminal input

•LINE1 is only for the CD terminal input.

E7Channel input LEVEL controls

These are used to adjust the levels of the selected inputs.

E8MIDI layer selector buttons

When these buttons are set to ON, the controls of the selected channels function as MIDI controllers.

E9Channel isolator EQ controls (HI, MID, LOW)

These are used to change the frequency response of the selected inputs.

At the center position, the frequency response is ﬂat.

At the –∞ position, the frequencies of all the bands are cut off completely.

R0CH LEVEL meter

Displays the input level after adjusted with LEVEL E7and Source EQ E9controls.

	Off:	Effector
	No signals input (under –60 dB/FS)
	Green:
	Signal input (–60 dB/FS to under –20 dB/FS)	Function
	Orange:
	Suitable signal input level (–20 dB/FS to under
	–6 dB/FS)
	–6 dB/FS)	Fader
	Red:
	Excessively high signal input level (above –6 dB/
	Excessively high signal input level (above –6 dB/	Start
	FS)	Start
	R4MIDI button
	R4MIDI button	USB
	Pressing this button makes the EFX control
	function as the MIDI controller.
	function as the MIDI controller.
	R5MIDI parameter control	Utility
	Controlling each button outputs the MIDI	Utility
	command.
	command.	Speciﬁ
	R6MIDI function buttons (FUNC1/2/3/4)
	Controlling each button outputs the MIDI
	command. Pressing the MIDI function button	cations
	while pressing the MIDI button makes it possible
	to switch the MIDI page. Different commands

		Troubleshooting
	can be output when the MIDI page is switched.