Roland VS-1680 owner manual Value, Gradation Curve, Marker Add

Page 21

Editing an automix

1.Press [PLAY (DISPLAY)].

2.Hold down [SHIFT] and press [F6 (UTIL)].

3.Press [PAGE] so that [F5] indicates “A.Mix,” and then press [F5 (A.Mix)].

fig.4-02

fig.4-04.e

Check marks

MEMO

You can rotate the TIME/VALUE dial to modify the automix setting value at the cursor location. If you wish to re-select

the type of automix data that will be edited, press [ ].

4.Press [F2 (Micro)].

5.Press [PAGE] so that [F1] indicates “In.”

fig.4-03

6.Make sure that the cursor is located at “Edit Target,” and use the TIME/VALUE dial to select the type of automix data to which you wish to apply the Gradation operation.

7.Use [][] to move the cursor to the first marker of the automix data to which you wish to apply the Gradation operation, and press [F1 (In)].

8.Use [][] to move the cursor to the last marker of the automix data to which you wish to apply the Gradation operation, and press [F1 (Out)]. Check marks will be added to the range selected for Gradation.

9.Press [F4 (Grad)].

10.Use [][][ ][ ] to move the cursor. Rotate the TIME/VALUE dial to set each parameter.

fig.4-16

Value

Adjust the beginning (In:) and end (Out:) of the Gradation area.

Gradation Curve

Select the curve by which the gradation will be created.

Linear: Linear.

Exp+: Convex above (exponential curve).

Exp-: Convex below (exponential curve). fig.4-17



	Linear			Exp+			Exp-

Marker Add

If this is turned “On,” markers will automatically be added to the area specified for gradation, in the optimal locations for the curve that you selected in “Gradation Curve.” If this is turned “Off,” markers will not be added.

22

Image 21

Contents 01898978 ‘99-3-E3-11T Table of Contents Precautions Automix editing functionality Additional effect algorithmsEnhanced support for CD-R/CD-RW drives Enhanced operationsExpanding the functionality of the VS-1680 If you purchasedIf you purchased the V-XPANDED system program Zip disk Expanding the functionality of the VS-1680 Added mastering tracks Mix 16 tracks down to 2 tracks Mastering RoomMixing down to the mastering tracks Cannot be usedTrk L track L Trk R track R StatusAfter Rec after recording MarkerSignal flow routing Mixdown shortcutPlaying back the mastering tracks Mixing down while inserting effects Off Rec EFX1 effect insert switchSnd effect send level Rtn effect return levelHold down STOP, and press Status for all tracks New effects algorithms EQ EqualizerExpander Compressor Mixer Enh Enhancer BCut Bass-cut filterInput Exp ExpanderMix Mixer Cmp CompressorLmt Limiter Out OutputModeling various speakers Speaker Modeling SpMod speaker modelingLFT/HFT Frequency trimmer Release Effective ways to use speaker modelingErasing data from a specific area Erase Editing an automixTarget Copying data to another location CopySmooth data transitions Gradation Destination TargetDestination Mark Value Gradation CurveMarker Add Press page so that F5 indicates A.Mix, and then Increasing or decreasing all data values Shift/ExpandExpand ShiftThreshold Using the VS-1680 with a CD-R/CD-RW drive Song writing procedureSpecifying the writing speed Speed Finalize Write MethodCD Speed Backup procedure Specifying the speed of saving SpeedSource Song Recovery procedure +VerifyX2 353 KBps X1 176 KBps Erase All Songs Attention Shortcut to the Phrase Edit window Enhancements related to operationCreating a new phrase Phrase New Sorting the take list SortDeleting a take Delete TakeTrack 1090 Naming a take Name14.e Type Dividing a phrase into two parts Phrase SplitMargin OUT ThresholdDivide Split To to point Group Linking the faders of two or more channels Fader GroupCopying mixer settings F4 Exec or Enter YESF6 Exit or Exit no Shift Lock on/off SHIFT+YES Removing direct current offset from the mix busDC Cut Checking inserted effects Icon and Patch Name display Enhancements to the display and specificationsEasy Routing Additional template Mastering Switching the Song Select window List displaySettings not stored in a scene Monitor Level Master Send switch display has been changed Pan→ MIXImmediate application of step-edited changes Index SymbolsInformation