Roland VS-1680 owner manual BCut Bass-cut filter, Enh Enhancer, Input, Exp Expander

Page 14

New effects algorithms

BCut (Bass-cut filter)

fig.3-04

 

 

 

 

 

This removes unwanted low-frequency components, such as

Level

L-SplitP

H-SplitP

 

 

 

pop noise.

 

 

 

Sw (Switch) Off, On

Low

Mid

High

 

 

 

Turns the bass-cut filter on/off.

Freq (Frequency) Thru, 20–2,000Hz

Freq

Adjusts the cutoff frequency of the bass-cut filter.

Enh (Enhancer)

This effect adds a phase-shifted signal to the original signal, enhancing the presence of the sound, and bringing it to the foreground.

Sw (Switch) Off, On

Turns the enhancer on/off.

Sens (Sensitivity) 0–100

Adjusts the degree to which the enhancer will respond to the volume of the input signal.

Freq (Frequency) 1.0–10.0kHz

Adjusts the frequency at which the enhancer will begin to take effect. The effect is applied at frequencies above the specified value.

MixLvl (Mix level) -24–+12dB

Adjusts the amount of effect sound that will be added to the original sound.

In (Input)

The input signal is divided into three parts by frequency band.

InputG (Input gain) -24–+12dB

Adjusts the overall volume level of the signal before it enters the expander (Exp) and compressor (Cmp).

D-Time (Detect time) 0–10ms

If the original signal is slightly delayed before being input, the expander/compressor will be able to use more processing time, and can adjust the level more appropriately. Adjusts the time by which the original signal is delayed. The output signal from the Mastering Tool Kit is delayed by the time set here.

L-SplitP (Low split point) 20–800Hz H-SplitP (High split point) 1.6–16kHz

Specify the frequencies at which the original signal will be split into three parts.

Exp (Expander)

This effect restricts the output by a specific ratio when low- level signals are input.

fig.3-05

 

Out

Threshold

 

1:1

1:2

In

Ratio

 

Sw (Switch) Off, On

Turns the expander on/off.

Low Thre (Low threshold) -80–0dB Mid Thre (Middle threshold) -80–0dB High Thre (High threshold) -80–0dB

Specify the level at which the expander will begin to take effect.

Low Ratio 1:1–1:16, 1:INF

Mid Ratio 1:1–1:16, 1:INF

High Ratio 1:1–1:16, 1:INF

Adjust the ratio by which the output is restricted when the input level is below the threshold level.

Low Atck (Low attack) 0–100ms Mid Atck (Middle attack) 0–100ms High Atck (High attack) 0–100ms

Adjust the time from when the input level falls below the threshold level until the expander begins to take effect.

Low Rel (Low release) 50–5,000ms Mid Rel (Middle release) 50–5,000ms High Rel (High release) 50–5,000ms

Adjust the time from when the input level exceeds the

threshold level until the expander effect is bypassed.

15

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 01898978 ‘99-3-E3-11T Table of Contents Precautions Enhanced support for CD-R/CD-RW drives Additional effect algorithmsAutomix editing functionality Enhanced operationsIf you purchased the V-XPANDED system program Zip disk Expanding the functionality of the VS-1680If you purchased Expanding the functionality of the VS-1680 Mixing down to the mastering tracks Mix 16 tracks down to 2 tracks Mastering RoomAdded mastering tracks Cannot be usedAfter Rec after recording StatusTrk L track L Trk R track R MarkerPlaying back the mastering tracks Signal flow routingMixdown shortcut Mixing down while inserting effects Snd effect send level EFX1 effect insert switchOff Rec Rtn effect return levelHold down STOP, and press Status for all tracks Expander Compressor Mixer New effects algorithmsEQ Equalizer Input BCut Bass-cut filterEnh Enhancer Exp ExpanderLmt Limiter Cmp CompressorMix Mixer Out OutputLFT/HFT Frequency trimmer Modeling various speakers Speaker ModelingSpMod speaker modeling Effective ways to use speaker modeling ReleaseEditing an automix Erasing data from a specific area EraseCopying data to another location Copy TargetDestination Mark Smooth data transitions GradationDestination Target Marker Add ValueGradation Curve Increasing or decreasing all data values Shift/Expand Press page so that F5 indicates A.Mix, and thenThreshold ExpandShift Specifying the writing speed Speed Using the VS-1680 with a CD-R/CD-RW driveSong writing procedure CD Speed FinalizeWrite Method Source Song Backup procedureSpecifying the speed of saving Speed X2 353 KBps X1 176 KBps Recovery procedure+Verify Erase All Songs Attention Creating a new phrase Phrase New Enhancements related to operationShortcut to the Phrase Edit window Sorting the take list SortTrack Deleting a take DeleteTake Naming a take Name 109014.e Margin Dividing a phrase into two parts Phrase SplitType OUT ThresholdDivide Split To to point Linking the faders of two or more channels Fader Group GroupF6 Exit or Exit no Copying mixer settingsF4 Exec or Enter YES DC Cut Shift Lock on/off SHIFT+YESRemoving direct current offset from the mix bus Enhancements to the display and specifications Checking inserted effects Icon and Patch Name displaySwitching the Song Select window List display Easy Routing Additional template MasteringImmediate application of step-edited changes Settings not stored in a scene Monitor LevelMaster Send switch display has been changed Pan→ MIX Symbols IndexInformation
Top Page Image Contents