Roland VS-1680 owner manual Specifying the speed of saving Speed, Backup procedure, Source Song

Page 26

Using the VS-1680 with a CD-R/CD-RW drive

9.Press [F4 (Exec)].

10.Press [YES]. A message about the license agreement will appear. Read the message carefully, and if you consent to

that, press [YES]. The data will begin to write to the CD- R disc. If you do not consent, press [NO]. You will return to step 2.

fig.5-06

MEMO

The message about the license agreement is the same as “About the License Agreement” on the back cover of the “VS-1680 Owner’s Manual.”

11.When the data has been written successfully, the display will ask “Write Another ?” (write to another disc?). If you wish to write the identical song data to another CD-R disc, insert the new disc into the CD-RW drive, and press [YES]. If you press [NO], you will return to step 2.

Saving a song to a CD-RW disc (Backup)

Checking whether the song was saved correctly (+Verify)

After backing up a song to a CD-RW disc, you can now check whether or not the data was saved correctly (i.e., check the recorded state of the data).

If as a result of the +Verify operation, you are warned that the song data has not been saved correctly, you should back up to a different disc.

NOTE

When backing up to a CD-R, we recommend that you use +Verify to check whether the backup was performed correctly. However, +Verify checks the entire surface of the disc, so it takes a considerable amount of time.

Specifying the speed of saving (Speed)

When backing up a song on a CD-RW disc, you can now specify the speed at which the data will be written.

Backup procedure

1.As the current drive, select the drive (internal IDE hard disk) that contains the song you wish to back up.

2.Insert a CD-RW disc into the drive.

3.Press [PLAY (DISPLAY)].

4.Hold down [SHIFT] and [F6 (UTILITY)].

5.Press [F2 (CDRBk)]. If [F2] does not indicate “CDRBk,”

first press [PAGE] so that “CDRBk” is displayed, and then press [F2 (CDRBk)].

fig.5-07

6.Use [][][ ][ ] to move the cursor, and rotate the TIME/VALUE dial to set the parameters.

fig.5-08

Source Song

The marked songs will be backed up. Move the cursor to a song that you wish to back up, and press [F3 (MARK)]. By pressing [F2 (ALL)] you can mark or unmark all songs at once. By pressing [F1 (SelSg)] you can view a list of the songs. At this time, mark a song and press [F1 (Back)].

27

Page 25 Page 27
Image 26
Page 25 Page 27
Contents 01898978 ‘99-3-E3-11T Table of Contents Precautions Enhanced support for CD-R/CD-RW drives Additional effect algorithmsAutomix editing functionality Enhanced operationsIf you purchased the V-XPANDED system program Zip disk Expanding the functionality of the VS-1680If you purchased Expanding the functionality of the VS-1680 Mixing down to the mastering tracks Mix 16 tracks down to 2 tracks Mastering RoomAdded mastering tracks Cannot be usedAfter Rec after recording StatusTrk L track L Trk R track R MarkerPlaying back the mastering tracks Signal flow routingMixdown shortcut Mixing down while inserting effects Snd effect send level EFX1 effect insert switchOff Rec Rtn effect return levelHold down STOP, and press Status for all tracks Expander Compressor Mixer New effects algorithmsEQ Equalizer Input BCut Bass-cut filterEnh Enhancer Exp ExpanderLmt Limiter Cmp CompressorMix Mixer Out OutputLFT/HFT Frequency trimmer Modeling various speakers Speaker ModelingSpMod speaker modeling Effective ways to use speaker modeling ReleaseEditing an automix Erasing data from a specific area EraseCopying data to another location Copy TargetDestination Mark Smooth data transitions GradationDestination Target Marker Add ValueGradation Curve Increasing or decreasing all data values Shift/Expand Press page so that F5 indicates A.Mix, and thenThreshold ExpandShift Specifying the writing speed Speed Using the VS-1680 with a CD-R/CD-RW driveSong writing procedure CD Speed FinalizeWrite Method Source Song Backup procedureSpecifying the speed of saving Speed X2 353 KBps X1 176 KBps Recovery procedure+Verify Erase All Songs Attention Creating a new phrase Phrase New Enhancements related to operationShortcut to the Phrase Edit window Sorting the take list SortTrack Deleting a take DeleteTake Naming a take Name 109014.e Margin Dividing a phrase into two parts Phrase SplitType OUT ThresholdDivide Split To to point Linking the faders of two or more channels Fader Group GroupF6 Exit or Exit no Copying mixer settingsF4 Exec or Enter YES DC Cut Shift Lock on/off SHIFT+YESRemoving direct current offset from the mix bus Enhancements to the display and specifications Checking inserted effects Icon and Patch Name displaySwitching the Song Select window List display Easy Routing Additional template MasteringImmediate application of step-edited changes Settings not stored in a scene Monitor LevelMaster Send switch display has been changed Pan→ MIX Symbols IndexInformation
Top Page Image Contents