Roland VS-1680 owner manual Erase All Songs Attention

Page 28

Using the VS-1680 with a CD-R/CD-RW drive

5.Press [F3 (CDRRc)]. If [F3] does not indicate “CDRRc,” first press [PAGE] so that “CDRRc” appears, and then

press [F3 (CDRRc)].

fig.5-12

6.Use [][][ ][ ] to move the cursor, and use the TIME/VALUE dial to set the parameters.

fig.5-13

Source Song

Marked songs will be loaded. Move the cursor to a song that you wish to recover, and press [F4 (MARK)]. By pressing [F3 (ALL)] you can mark or unmark all songs at once. By pressing [F2 (SelSg)] you can view a list of the songs. At this time, mark the desired song, and press [F1 (Back)].

Erase All Songs <<ATTENTION>>

If this is “On,” the current drive will be initialized before the song data is recovered. If you wish to recover while preserving the songs that are saved on the current drive, set this “Off.”

CD Speed

Select the speed at which the song data will be recovered from disc.

x6 (1058 KBps): Recover at 6x speed (1058 kilobytes per second).

x2 (353 KBPs): Recover at double speed (353 kilobytes per second).

x1 (176 KBPs): Recover at normal speed (176 kilobytes per second). This will allow greater reliability.

NOTE

Depending on the disc, it may not be possible to recover reliably from some CD-R discs at speeds of “x6 (1058 KBps)” or

“x2 (353 KBPs).” In this case, select “x1 (176 KBPs).” Even if the “CD Speed” is set to “x2 (353 KBps)” or

“x6 (1058 KBps)” the time it takes for recovery is not always 1/2 or 1/6 of the base. This is because writing to the internal hard disk can take a lot of time, or disc read errors can sometimes occur.

7.Press [F4 (Exec)]. A message will ask you for

confirmation.

fig.5-14

8.Press [YES]. The display will ask “STORE Current?” (store the current song?).

9.If you wish to store the current song, press [YES]. If not, press [NO]. If a demo song is selected, press [NO].

10.The recovery operation will begin. If the data has been backed up to multiple discs, the disc will be ejected, and you will be prompted to “Insert Disc #” (# is the order number of each disk). Insert the next disc and press [YES].

fig.5-11

11.When the CD-R recovery ends, you are returned to Play condition.

29

Page 27 Page 29
Image 28
Page 27 Page 29
Contents 01898978 ‘99-3-E3-11T Table of Contents Precautions Additional effect algorithms Automix editing functionalityEnhanced support for CD-R/CD-RW drives Enhanced operationsIf you purchased Expanding the functionality of the VS-1680If you purchased the V-XPANDED system program Zip disk Expanding the functionality of the VS-1680 Mix 16 tracks down to 2 tracks Mastering Room Added mastering tracksMixing down to the mastering tracks Cannot be usedStatus Trk L track L Trk R track RAfter Rec after recording MarkerMixdown shortcut Signal flow routingPlaying back the mastering tracks Mixing down while inserting effects EFX1 effect insert switch Off RecSnd effect send level Rtn effect return levelHold down STOP, and press Status for all tracks EQ Equalizer New effects algorithmsExpander Compressor Mixer BCut Bass-cut filter Enh EnhancerInput Exp ExpanderCmp Compressor Mix MixerLmt Limiter Out OutputSpMod speaker modeling Modeling various speakers Speaker ModelingLFT/HFT Frequency trimmer Effective ways to use speaker modeling ReleaseEditing an automix Erasing data from a specific area EraseCopying data to another location Copy TargetDestination Target Smooth data transitions GradationDestination Mark Gradation Curve ValueMarker Add Increasing or decreasing all data values Shift/Expand Press page so that F5 indicates A.Mix, and thenShift ExpandThreshold Song writing procedure Using the VS-1680 with a CD-R/CD-RW driveSpecifying the writing speed Speed Write Method FinalizeCD Speed Specifying the speed of saving Speed Backup procedureSource Song +Verify Recovery procedureX2 353 KBps X1 176 KBps Erase All Songs Attention Enhancements related to operation Shortcut to the Phrase Edit windowCreating a new phrase Phrase New Sorting the take list SortTake Deleting a take DeleteTrack Naming a take Name 109014.e Dividing a phrase into two parts Phrase Split TypeMargin OUT ThresholdDivide Split To to point Linking the faders of two or more channels Fader Group GroupF4 Exec or Enter YES Copying mixer settingsF6 Exit or Exit no Removing direct current offset from the mix bus Shift Lock on/off SHIFT+YESDC Cut Enhancements to the display and specifications Checking inserted effects Icon and Patch Name displaySwitching the Song Select window List display Easy Routing Additional template MasteringMaster Send switch display has been changed Pan→ MIX Settings not stored in a scene Monitor LevelImmediate application of step-edited changes Symbols IndexInformation
Top Page Image Contents