Peavey ICA 400V, ICA Series manual Introduction, Unpacking, Installation and Mounting, Basic Setup

Page 4

ENGLISH

INTRODUCTION

Congratulations on your purchase of an Architectural Acoustics ICA™ (Industrial Contractor Amplifier) from Peavey Electronics. Please read this manual carefully, especially the IMPORTANT SAFETY INSTRUCTIONS on page 18. It contains information vital to safe operation of the power amplifier. Also, please fill out and return the enclosed product registration card.

ICA Series amplifiers represent new levels of value and flexibility never before offered to the contracting market. The ICA Series features models specifically designed to drive 4-ohm outputs, 70.7-volt outputs, and 100-volt outputs. 70.7 and 100-volt outputs can be driven directly, eliminating the need for transformers or autoformers. These amplifiers cover almost every installed or distributed sound power requirement imaginable.

ICA Series amplifiers are ruggedly built from high-quality components and feature comprehensive protection circuits to protect your amplifier from those “real world” occurrences.

If you need setup or operational assistance for this product, please call the Peavey Electronics Customer Service Department or your local Peavey Electronics representative. We appreciate suggestions that may help us improve our products and/or service.

UNPACKING

Inspect the amplifier during unpacking. If you find any damage, notify your dealer immediately. Only the consignee may institute a claim with the carrier for damage incurred during shipping. Be sure to save the carton and all packing materials. Should you ever need to ship the unit back to Peavey Electronics, one of its service centers, or the dealer; use only the original factory packing.

INSTALLATION AND MOUNTING

ICA Series amplifiers are 2 or 3-rack-space units of 15 3/4" (400 mm) depth that mount in a standard 19" rack. On all amplifiers, front panel mounting holes are provided.

BASIC SETUP

1.Rack mount the amplifier in the location where it is to be used, remembering to allow for adequate access and cooling space. For more information, see the sections on INSTALLATION AND MOUNTING and COOLING REQUIREMENTS.

2.Make input connections to the plugable terminal blocks on the rear panel. Use the proper connections for stereo, parallel, bridged mono, and grounding configuration. See the sections on SIGNAL MODE CONFIGURATION and INPUT MODULE CONNECTIONS for more information.

3.Connect speakers to the output barrier strip. Be sure to make the correct output connections for stereo, parallel or bridged mono configuration. See the section on SPEAKER OUTPUT CONNECTIONS for more information.

4.Make power connections, allowing for proper current draw. See the sections on IEC POWER CONNECTOR and AC MAINS CIRCUIT SIZE REQUIREMENTS for more information.

5.Turn the front panel 3-position AC POWER switch to ON and bring up the back panel LEVEL (gain) attenuators to the desired levels.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents A S E R I E S Page Table of Contents Installation and Mounting Basic SetupIntroduction UnpackingFront Panel Features Position AC Power SwitchPower LED Signal LEDBack Panel Features Input Section IEC Power ConnectorSequential TURN-ON Connector Output Barrier StripOperation Signal Mode Configuration Stereo Mode Connection Diagram Parallel Mode DiagramProtection Features Sequential TURN-ON / TURN-OFF FADE-IN ProtectionThermal Protection Short CircuitWire Gauge Chart ICA 600 Specifications Rated Power 2 X 4 ohms Slew Rate CoolingICA 1200 Specifications Gross Weight 51.4 lbs .3 kg Net WeightICA 2400 Specifications ICA 400V Specifications THD two channels driven ICAICA 800V Specifications ICA 2400V Specifications Introducción DesempacarInstalación Y Montura Instalación BásicaInterruptor DE Poder AC Power DE Tres Posiciones Características DEL Panel FrontalInstalador Para Rack LED DE PoderSección DE Entrada Características DEL Panel TraseroConectores DE Salida DE Para Cables Operación Diagrama DE Modo Estéreo Diagrama DE Modo Paralelo Diagrama DE Modo Puenteado Conexiones DE Salida DE BocinasConexión DE Tierra Características DE ProtecciónProtección DE FADE-IN Protección TérmicaCorto Circuito Protección DE Voltaje DE CDFicha DE Medidas DE Cables Especificaciones del ICA Razón de Slew Topología Especificaciones del ICA 400V Poder Medido dos canales THD Distorsión Total Armónica dos canales Deballage InstallationMise EN Route LED DE Signal Panneau AvantPattes DE Fixation Rack Interrupteur 3-POSITIONS D’ALIMENTATIONPanneau Arriere EntreesSorties Connecteur D’ALIMENTATION IECConfiguration DU Signal D’ENTREE Alimentation ElectriqueRefroidissement Emissions ThermiquesStereo Mode Connection Diagram Parallel Mode Diagram Masse DU Signal Systemes DE ProtectionConnexions HAUTS-PARLEUR Clip LimiteurMise EN ROUTE/ARRET Sequentiels Protection DE Mise EN RouteProtection Thermale Protection DE Court CircuitStranded Power ICA 600 Specifications ICA 1200 Specifications ICA 2400 Specifications ICA 400V Specifications ICA 800V Specifications Input Cmrr Rated Power one channel Einleitung AuspackenEinbau UND Anschluss Erste SchrittePOWER-LED SIGNAL-LEDVorderseite Montagezubehör FÜR DEN RACK-EINBAULFC-LED PROTECT-LEDRückseite EingangsmodulBedienung Betriebsarten WärmeentwicklungSTEREO-BETRIEB Signalerdung PARALLEL-BETRIEBBrückenbetrieb LautsprecheranschlussCLIP-LIMITER LastfehlerkorrekturEinschaltverzögerung ÜberhitzungsschutzVerkabelung Sequentielle Ein/Ausschalt-Funktion Wire Gauge Chart ICA 600 Specifications ICA 1200 Specifications ICA 2400 Specifications ICA 400V Specifications ICA 800V Specifications ICA 2400V Specifications Page Peavey Electronics Corporation Limited Warranty Important Safety Instructions 80304800
Top Page Image Contents