Peavey ICA Series, ICA 600, ICA 400V, ICA 2400V, ICA 1200 manual ICA 800V Specifications

Page 59

ICA800V SPECIFICATIONS

Rated Power (two channels): 400 watts @ 20 Hz - 20 kHz both channels driven at < 0.1% THD

Rated Power (one channel):

415 watts @ 1 kHz at < 0.01% THD

Minimum Load Impedance: ICA 800V-70: 12.5 ohms ICA 800V-100: 25 ohms

Maximum RMS Voltage Swing: ICA 800V-70: 85 volts

ICA 800V-100: 110 volts

Frequency Response:

10 Hz - 25 kHz; +0, -.3 dB at 1 watt

Power Bandwidth:

ICA 800V-70:

10 Hz - 100 kHz; +0, -3 dB at rated power

ICA 800V-100:

10 Hz - 50 kHz; +0, -3 dB at rated power

THD (two channels driven): ICA 800V-70:

<0.15% @ 400 W from 20 Hz -

20 kHz with both channels driven ICA 800V-100:

<0.1% @ 400 W from 20 Hz - 20 kHz with both channels driven

THD (one channel driven): <0.008% @ 400 W @ 1 kHz

SMPTE IMD:

<0.1% 60 Hz and 7 kHz, @ 400 W

Slew Rate:

35 V/µs

Damping Factor:

>400:1 @ 20 Hz - 400 Hz

Input CMRR:

>-65 dB @ 1 kHz

Voltage Gain:

x40 (32 dB)

Input Sensitivity:

ICA 800V-70:

1.77volts for rated output ICA 800V-100:

2.5volts for rated output

Input Impedance:

20 k ohms, balanced

Hum and Noise:

>-108 dB, “A” weighted referenced to rated power

Crosstalk:

>-65 dB, “A” weighted referenced to rated power

Current Draw @ 1/8 power:

ICA 800V-70: 765 watts

ICA 800V-100: 775 watts

Current Draw @ 1/3 power:

ICA 800V-70: 1,100 watts

ICA 800V-100: 1,150 watts

Idle Current Draw:

45 watts in Standby Mode

Maximum Current Draw:

ICA 800V-70:

1,680 watts for rated power ICA 800V-100:

1,700 watts for rated power

Thermal Emissions (BTU/hr.): 550 @ 1/8 power,

835 @ 1/3 power

Cooling:

120 mm DC fan, off until heatsinks reach 45o C, then variable speed

Controls:

2 rear panel attenuators, sequential turn-on / off

Indicator LEDs:

2 Clip, 2 Signal, 2 LFC, 1 Protect,

1 Power

Protection:

Temp., DC, turn-on bursts, subsonic, incorrect load or short

Connectors:

8-pin plugable signal input, 4-pin plugable sequential power,

4-terminal barrier strip, IEC AC power connector

Construction:

All steel; 16 ga. chassis, 18 ga. top, 12 ga. rack ears

Dimensions: 5.25" x 19" x 16.4"

133 mm x 483 mm x 416.6 mm

Gross Weight: 51.4 lbs. (23.3 kg.)

Net Weight:

45 lbs. (20.4 kg.)

Due to our efforts for constant improvements, features and specifications are subject to change without notice.

59

Image 59
Contents A S E R I E S Page Table of Contents Unpacking Installation and MountingBasic Setup IntroductionSignal LED Front Panel FeaturesPosition AC Power Switch Power LEDOutput Barrier Strip Back Panel Features Input SectionIEC Power Connector Sequential TURN-ON ConnectorOperation Stereo Mode Connection Diagram Parallel Mode Diagram Signal Mode ConfigurationProtection Features Short Circuit Sequential TURN-ON / TURN-OFFFADE-IN Protection Thermal ProtectionWire Gauge Chart Rated Power 2 X 4 ohms Slew Rate Cooling ICA 600 SpecificationsGross Weight 51.4 lbs .3 kg Net Weight ICA 1200 SpecificationsICA 2400 Specifications THD two channels driven ICA ICA 400V SpecificationsICA 800V Specifications ICA 2400V Specifications Instalación Básica IntroducciónDesempacar Instalación Y MonturaLED DE Poder Interruptor DE Poder AC Power DE Tres PosicionesCaracterísticas DEL Panel Frontal Instalador Para RackConectores DE Salida DE Para Cables Características DEL Panel TraseroSección DE Entrada Operación Diagrama DE Modo Estéreo Diagrama DE Modo Paralelo Características DE Protección Diagrama DE Modo PuenteadoConexiones DE Salida DE Bocinas Conexión DE TierraProtección DE Voltaje DE CD Protección DE FADE-INProtección Térmica Corto CircuitoFicha DE Medidas DE Cables Especificaciones del ICA Razón de Slew Topología Especificaciones del ICA 400V Poder Medido dos canales THD Distorsión Total Armónica dos canales Mise EN Route InstallationDeballage Interrupteur 3-POSITIONS D’ALIMENTATION LED DE SignalPanneau Avant Pattes DE Fixation RackConnecteur D’ALIMENTATION IEC Panneau ArriereEntrees SortiesEmissions Thermiques Configuration DU Signal D’ENTREEAlimentation Electrique RefroidissementStereo Mode Connection Diagram Parallel Mode Diagram Clip Limiteur Masse DU SignalSystemes DE Protection Connexions HAUTS-PARLEURProtection DE Court Circuit Mise EN ROUTE/ARRET SequentielsProtection DE Mise EN Route Protection ThermaleStranded Power ICA 600 Specifications ICA 1200 Specifications ICA 2400 Specifications ICA 400V Specifications ICA 800V Specifications Input Cmrr Rated Power one channel Erste Schritte EinleitungAuspacken Einbau UND AnschlussMontagezubehör FÜR DEN RACK-EINBAU POWER-LEDSIGNAL-LED VorderseiteEingangsmodul LFC-LEDPROTECT-LED RückseiteBedienung STEREO-BETRIEB WärmeentwicklungBetriebsarten Lautsprecheranschluss SignalerdungPARALLEL-BETRIEB BrückenbetriebÜberhitzungsschutz CLIP-LIMITERLastfehlerkorrektur EinschaltverzögerungVerkabelung Sequentielle Ein/Ausschalt-Funktion Wire Gauge Chart ICA 600 Specifications ICA 1200 Specifications ICA 2400 Specifications ICA 400V Specifications ICA 800V Specifications ICA 2400V Specifications Page Peavey Electronics Corporation Limited Warranty Important Safety Instructions 80304800