Peavey ICA 1200, ICA Series, ICA 800V, ICA 400V, ICA 2400V manual ICA 600 Specifications

Page 55

ICA600 SPECIFICATIONS

Rated Power (2 X 4 ohms):

Slew Rate:

Cooling:

300 watts @ 20 Hz - 20 kHz, both

30 V/µs

80 mm DC fan, off until heatsinks

channels driven at < 0.1% THD

 

reach 45° C, then variable speed

 

Damping Factor (8 ohms):

 

Rated Power (2 x 8 ohms):

>450:1 @ 20 Hz - 1 kHz

Controls:

200 watts @ 20 Hz - 20 kHz at

 

2 rear panel attenuators, sequential

< 0.05% THD

Input CMRR:

turn-on / off

 

>-65 dB @ 1 kHz

 

Rated Power (1 x 4 ohms):

 

Indicator LEDs:

360 watts @ 1 kHz at < 0.015% THD

Voltage Gain:

2 Clip, 2 Signal, 2 LFC, 1 Protect,

 

x40 (32 dB)

1 Power

Rated Power (1 x 8 ohms):

 

 

275 watts @ 1 kHz at < 0.005%

Input Sensitivity:

Protection:

THD

.866 volts @ 4 ohms, 1 volt @

Temp., DC, turn-on bursts, subsonic,

 

8 ohms

incorrect load or short

Minimum Load Impedance:

 

 

4 ohms

Input Impedance:

Connectors:

 

20 k ohms, balanced

8-pin plugable signal input, 4-pin

Maximum RMS Voltage Swing:

 

plugable sequential power,

57 volts

Hum and Noise:

4-terminal barrier strip, IEC AC

 

>-108 dB, “A” weighted referenced

power connector

Frequency Response:

to rated power @ 8 ohms

 

10 Hz - 25 kHz; +0, -3 dB at 1 watt

 

Construction:

 

Crosstalk:

All steel; 16 ga. chassis, 18 ga. top,

Power Bandwidth:

>-75 dB, “A” weighted referenced to

12 ga. rack ears

10 Hz - 100 kHz; +0, -3 dB at rated

rated power @ 8 ohms

 

power

 

Dimensions:

 

Current Draw @ 1/8 power:

3.48" x 19" x 16.4"

THD (2 x 4 ohms):

670 watts @ 4 ohms, 460 watts @

88.4 mm x 483 mm x 416.6 mm

<0.1% @ 300 W from 20 Hz - 20 kHz

8 ohms

 

with both channels driven

 

Gross Weight:

 

Current Draw @ 1/3 power:

33.6 lbs. (15.25 kg)

THD (2 x 8 ohms):

1,055 watts @ 4 ohms, 650 watts @

 

<0.05% @ 200 W from 20 Hz -

8 ohms

Net Weight:

20 kHz with both channels driven

 

30.2 lbs. (13.7 kg)

 

Idle Current Draw:

 

THD (1 x 4 ohms):

30 watts in Standby Mode

 

<0.01% @ 350 W @ 1 kHz

 

 

 

Maximum Current Draw:

 

THD (1 x 8 ohms):

1,622 watts @ 4 ohms, 1,010 watts

 

<0.005% @ 275 W @ 1 kHz

@ 8 ohms

 

SMPTE IMD:

Thermal Emissions (BTU/hr.):

 

<0.1% 60 Hz and 7 kHz, 300 W @

625 @ 1/3 power 4 ohms,

 

4 ohms

500 @ 1/3 power 8 ohms,

 

 

395 @ 1/8 power 4 ohms,

 

 

350 @ 1/8 power 8 ohms

 

Due to our efforts for constant improvements, features and specifications are subject to change without notice.

55

Image 55
Contents A S E R I E S Page Table of Contents Unpacking Installation and MountingBasic Setup IntroductionSignal LED Front Panel FeaturesPosition AC Power Switch Power LEDOutput Barrier Strip Back Panel Features Input SectionIEC Power Connector Sequential TURN-ON ConnectorOperation Stereo Mode Connection Diagram Parallel Mode Diagram Signal Mode ConfigurationProtection Features Short Circuit Sequential TURN-ON / TURN-OFFFADE-IN Protection Thermal ProtectionWire Gauge Chart Rated Power 2 X 4 ohms Slew Rate Cooling ICA 600 SpecificationsGross Weight 51.4 lbs .3 kg Net Weight ICA 1200 SpecificationsICA 2400 Specifications THD two channels driven ICA ICA 400V SpecificationsICA 800V Specifications ICA 2400V Specifications Instalación Básica IntroducciónDesempacar Instalación Y MonturaLED DE Poder Interruptor DE Poder AC Power DE Tres PosicionesCaracterísticas DEL Panel Frontal Instalador Para RackSección DE Entrada Características DEL Panel TraseroConectores DE Salida DE Para Cables Operación Diagrama DE Modo Estéreo Diagrama DE Modo Paralelo Características DE Protección Diagrama DE Modo PuenteadoConexiones DE Salida DE Bocinas Conexión DE TierraProtección DE Voltaje DE CD Protección DE FADE-INProtección Térmica Corto CircuitoFicha DE Medidas DE Cables Especificaciones del ICA Razón de Slew Topología Especificaciones del ICA 400V Poder Medido dos canales THD Distorsión Total Armónica dos canales Deballage InstallationMise EN Route Interrupteur 3-POSITIONS D’ALIMENTATION LED DE SignalPanneau Avant Pattes DE Fixation RackConnecteur D’ALIMENTATION IEC Panneau ArriereEntrees SortiesEmissions Thermiques Configuration DU Signal D’ENTREEAlimentation Electrique RefroidissementStereo Mode Connection Diagram Parallel Mode Diagram Clip Limiteur Masse DU SignalSystemes DE Protection Connexions HAUTS-PARLEURProtection DE Court Circuit Mise EN ROUTE/ARRET SequentielsProtection DE Mise EN Route Protection ThermaleStranded Power ICA 600 Specifications ICA 1200 Specifications ICA 2400 Specifications ICA 400V Specifications ICA 800V Specifications Input Cmrr Rated Power one channel Erste Schritte EinleitungAuspacken Einbau UND AnschlussMontagezubehör FÜR DEN RACK-EINBAU POWER-LEDSIGNAL-LED VorderseiteEingangsmodul LFC-LEDPROTECT-LED RückseiteBedienung Betriebsarten WärmeentwicklungSTEREO-BETRIEB Lautsprecheranschluss SignalerdungPARALLEL-BETRIEB BrückenbetriebÜberhitzungsschutz CLIP-LIMITERLastfehlerkorrektur EinschaltverzögerungVerkabelung Sequentielle Ein/Ausschalt-Funktion Wire Gauge Chart ICA 600 Specifications ICA 1200 Specifications ICA 2400 Specifications ICA 400V Specifications ICA 800V Specifications ICA 2400V Specifications Page Peavey Electronics Corporation Limited Warranty Important Safety Instructions 80304800