Peavey ICA 400V, ICA Series, ICA 600, ICA 800V, ICA 1200 manual ICA 2400V Specifications

Page 60

ICA2400V SPECIFICATIONS

Rated Power (2 x 4 ohms):

1200 watts @ 20 Hz - 20 kHz both channels driven at < 0.1% THD

Rated Power (2 x 8 ohms):

800 watts @ 20 Hz – 20 kHz both channels driven at < 0.08% THD

Rated Power (1 x 4 ohms):

1325 watts @ 1 kHz at < 0.08% THD

Rated Power (1 x 8 ohms):

830 watts @ 1 kHz at < 0.08% THD

Topology:

Class H

Minimum Load Impedance:

4 ohms

Maximum RMS Voltage Swing: 95 volts

Frequency Response:

10 Hz – 25 kHz; +0, -.3 dB at 1 watt

Power Bandwidth:

10 Hz – 50 kHz; +0, -3 dB at rated power

THD (2 x 4 ohms):

<0.025% @ 1200 W @ 1 kHz with both channels driven

THD (2 x 8 ohms):

<0.008% @ 800 W @ 1 kHz with both channels driven

THD (1 x 4 ohms): <0.015% @ 1325 W @ 1kHz

THD (1 x 8 ohms): <0.006% @ 830 W @ 1kHz

SMPTE IMD:

<0.1% 60 Hz and 7 kHz, 800 W @ 8 ohms

Slew Rate:

35 V/us

Damping Factor (8 ohms):

>250:1 @ 20 Hz – 1 kHz

Input CMRR:

> 65 dB @ 1 kHz

Voltage Gain:

x 40 (32 dB)

Input Sensitivity:

1.73volts @ 4 ohms, 2 volts @ 8 ohms

Input Impedance:

20 k ohms, balanced

Hum and Noise:

>-115 dB, “A” weighted referenced to rated power @ 8 ohms

Crosstalk:

>-55 dB, “A” weighted referenced to rated power @ 8 ohms

Current Draw @ 1/8 power:

575 watts @ 4 ohms, 380 watts @

8 ohms

Current Draw @ 1/3 power:

1185 watts @ 4 ohms, 860 watts @

8 ohms

Idle Current Draw:

35 VA in Standby Mode

Maximum Current Draw:

2,760 VA (time limited by breaker)

Thermal Emissions (BTU/hr.): 940 @ 1/8 power 4 ohms, 615 @ 1/8 power 8 ohms, 1830 @ 1/3 power 4 ohms, 1335 @ 1/3 power @ 8 ohms

Cooling:

120 mm DC fan, off until heatsinks reach 45° C, then variable speed

Controls:

2 rear panel attenuators, sequential turn-on / off

Indicator LEDs:

2 Clip, 2 Signal, 2 LFC, 1 Protect,

1 Power

Protection:

Temp., DC, turn-on bursts, subsonic, incorrect load or short

Connectors:

8-pin plugable signal input, 4-pin plugable sequential power, 4-terminal barrier strip, IEC AC power connector

Construction:

All steel; 16 ga. chassis, 18 ga. top, 12 ga. rack ears

Dimensions:

5.25" x 19" x 16.4"

133 mm x 483 mm x 416.6 mm,

Gross Weight:

51.4 lbs. (23.3 kg.)

Net Weight:

45 lbs. (20.4 kg.)

Due to our efforts for constant improvements, features and specifications are subject to change without notice.

60

Image 60
Contents A S E R I E S Page Table of Contents Installation and Mounting Basic SetupIntroduction UnpackingFront Panel Features Position AC Power SwitchPower LED Signal LEDBack Panel Features Input Section IEC Power ConnectorSequential TURN-ON Connector Output Barrier StripOperation Signal Mode Configuration Stereo Mode Connection Diagram Parallel Mode DiagramProtection Features Sequential TURN-ON / TURN-OFF FADE-IN ProtectionThermal Protection Short CircuitWire Gauge Chart ICA 600 Specifications Rated Power 2 X 4 ohms Slew Rate CoolingICA 1200 Specifications Gross Weight 51.4 lbs .3 kg Net WeightICA 2400 Specifications ICA 400V Specifications THD two channels driven ICAICA 800V Specifications ICA 2400V Specifications Introducción DesempacarInstalación Y Montura Instalación BásicaInterruptor DE Poder AC Power DE Tres Posiciones Características DEL Panel FrontalInstalador Para Rack LED DE PoderCaracterísticas DEL Panel Trasero Sección DE EntradaConectores DE Salida DE Para Cables Operación Diagrama DE Modo Estéreo Diagrama DE Modo Paralelo Diagrama DE Modo Puenteado Conexiones DE Salida DE BocinasConexión DE Tierra Características DE ProtecciónProtección DE FADE-IN Protección TérmicaCorto Circuito Protección DE Voltaje DE CDFicha DE Medidas DE Cables Especificaciones del ICA Razón de Slew Topología Especificaciones del ICA 400V Poder Medido dos canales THD Distorsión Total Armónica dos canales Installation DeballageMise EN Route LED DE Signal Panneau AvantPattes DE Fixation Rack Interrupteur 3-POSITIONS D’ALIMENTATIONPanneau Arriere EntreesSorties Connecteur D’ALIMENTATION IECConfiguration DU Signal D’ENTREE Alimentation ElectriqueRefroidissement Emissions ThermiquesStereo Mode Connection Diagram Parallel Mode Diagram Masse DU Signal Systemes DE ProtectionConnexions HAUTS-PARLEUR Clip LimiteurMise EN ROUTE/ARRET Sequentiels Protection DE Mise EN RouteProtection Thermale Protection DE Court CircuitStranded Power ICA 600 Specifications ICA 1200 Specifications ICA 2400 Specifications ICA 400V Specifications ICA 800V Specifications Input Cmrr Rated Power one channel Einleitung AuspackenEinbau UND Anschluss Erste SchrittePOWER-LED SIGNAL-LEDVorderseite Montagezubehör FÜR DEN RACK-EINBAULFC-LED PROTECT-LEDRückseite EingangsmodulBedienung Wärmeentwicklung BetriebsartenSTEREO-BETRIEB Signalerdung PARALLEL-BETRIEBBrückenbetrieb LautsprecheranschlussCLIP-LIMITER LastfehlerkorrekturEinschaltverzögerung ÜberhitzungsschutzVerkabelung Sequentielle Ein/Ausschalt-Funktion Wire Gauge Chart ICA 600 Specifications ICA 1200 Specifications ICA 2400 Specifications ICA 400V Specifications ICA 800V Specifications ICA 2400V Specifications Page Peavey Electronics Corporation Limited Warranty Important Safety Instructions 80304800