Peavey ICA Series, ICA 600, ICA 400V, ICA 2400V, ICA 1200 manual ICA 800V Specifications

Page 16

ICA800V SPECIFICATIONS

Rated Power (two channels): 400 watts @ 20 Hz - 20 kHz both channels driven at < 0.1% THD

Rated Power (one channel):

415 watts @ 1 kHz at < 0.01% THD

Minimum Load Impedance: ICA 800V-70: 12.5 ohms ICA 800V-100: 25 ohms

Maximum RMS Voltage Swing: ICA 800V-70: 85 volts

ICA 800V-100: 110 volts

Frequency Response:

10 Hz - 25 kHz; +0, -.3 dB at 1 watt

Power Bandwidth:

ICA 800V-70:

10 Hz - 100 kHz; +0, -3 dB at rated power

ICA 800V-100:

10 Hz - 50 kHz; +0, -3 dB at rated power

THD (two channels driven): ICA 800V-70:

<0.15% @ 400 W from 20 Hz -

20 kHz with both channels driven ICA 800V-100:

<0.1% @ 400 W from 20 Hz - 20 kHz with both channels driven

THD (one channel driven): <0.008% @ 400 W @ 1 kHz

SMPTE IMD:

<0.1% 60 Hz and 7 kHz, @ 400 W

Slew Rate:

35 V/µs

Damping Factor:

>400:1 @ 20 Hz - 400 Hz

Input CMRR:

>-65 dB @ 1 kHz

Voltage Gain:

x40 (32 dB)

Input Sensitivity:

ICA 800V-70:

1.77volts for rated output ICA 800V-100:

2.5volts for rated output

Input Impedance:

20 k ohms, balanced

Hum and Noise:

>-108 dB, “A” weighted referenced to rated power

Crosstalk:

>-65 dB, “A” weighted referenced to rated power

Current Draw @ 1/8 power:

ICA 800V-70: 765 watts

ICA 800V-100: 775 watts

Current Draw @ 1/3 power:

ICA 800V-70: 1,100 watts

ICA 800V-100: 1,150 watts

Idle Current Draw:

45 watts in Standby Mode

Maximum Current Draw:

ICA 800V-70:

1,680 watts for rated power ICA 800V-100:

1,700 watts for rated power

Thermal Emissions (BTU/hr.): 550 @ 1/8 power,

835 @ 1/3 power

Cooling:

120 mm DC fan, off until heatsinks reach 45o C, then variable speed

Controls:

2 rear panel attenuators, sequential turn-on / off

Indicator LEDs:

2 Clip, 2 Signal, 2 LFC, 1 Protect,

1 Power

Protection:

Temp., DC, turn-on bursts, subsonic, incorrect load or short

Connectors:

8-pin plugable signal input, 4-pin plugable sequential power,

4-terminal barrier strip, IEC AC power connector

Construction:

All steel; 16 ga. chassis, 18 ga. top, 12 ga. rack ears

Dimensions: 5.25" x 19" x 16.4"

133 mm x 483 mm x 416.6 mm

Gross Weight: 51.4 lbs. (23.3 kg.)

Net Weight:

45 lbs. (20.4 kg.)

Due to our efforts for constant improvements, features and specifications are subject to change without notice.

16

Image 16
Contents A S E R I E S Page Table of Contents Installation and Mounting Basic SetupIntroduction UnpackingFront Panel Features Position AC Power SwitchPower LED Signal LEDBack Panel Features Input Section IEC Power ConnectorSequential TURN-ON Connector Output Barrier StripOperation Signal Mode Configuration Stereo Mode Connection Diagram Parallel Mode DiagramProtection Features Sequential TURN-ON / TURN-OFF FADE-IN ProtectionThermal Protection Short CircuitWire Gauge Chart ICA 600 Specifications Rated Power 2 X 4 ohms Slew Rate CoolingICA 1200 Specifications Gross Weight 51.4 lbs .3 kg Net WeightICA 2400 Specifications ICA 400V Specifications THD two channels driven ICAICA 800V Specifications ICA 2400V Specifications Introducción DesempacarInstalación Y Montura Instalación BásicaInterruptor DE Poder AC Power DE Tres Posiciones Características DEL Panel FrontalInstalador Para Rack LED DE PoderSección DE Entrada Características DEL Panel TraseroConectores DE Salida DE Para Cables Operación Diagrama DE Modo Estéreo Diagrama DE Modo Paralelo Diagrama DE Modo Puenteado Conexiones DE Salida DE BocinasConexión DE Tierra Características DE ProtecciónProtección DE FADE-IN Protección TérmicaCorto Circuito Protección DE Voltaje DE CDFicha DE Medidas DE Cables Especificaciones del ICA Razón de Slew Topología Especificaciones del ICA 400V Poder Medido dos canales THD Distorsión Total Armónica dos canales Deballage InstallationMise EN Route LED DE Signal Panneau AvantPattes DE Fixation Rack Interrupteur 3-POSITIONS D’ALIMENTATIONPanneau Arriere EntreesSorties Connecteur D’ALIMENTATION IECConfiguration DU Signal D’ENTREE Alimentation ElectriqueRefroidissement Emissions ThermiquesStereo Mode Connection Diagram Parallel Mode Diagram Masse DU Signal Systemes DE ProtectionConnexions HAUTS-PARLEUR Clip LimiteurMise EN ROUTE/ARRET Sequentiels Protection DE Mise EN RouteProtection Thermale Protection DE Court CircuitStranded Power ICA 600 Specifications ICA 1200 Specifications ICA 2400 Specifications ICA 400V Specifications ICA 800V Specifications Input Cmrr Rated Power one channel Einleitung AuspackenEinbau UND Anschluss Erste SchrittePOWER-LED SIGNAL-LEDVorderseite Montagezubehör FÜR DEN RACK-EINBAULFC-LED PROTECT-LEDRückseite EingangsmodulBedienung Betriebsarten WärmeentwicklungSTEREO-BETRIEB Signalerdung PARALLEL-BETRIEBBrückenbetrieb LautsprecheranschlussCLIP-LIMITER LastfehlerkorrekturEinschaltverzögerung ÜberhitzungsschutzVerkabelung Sequentielle Ein/Ausschalt-Funktion Wire Gauge Chart ICA 600 Specifications ICA 1200 Specifications ICA 2400 Specifications ICA 400V Specifications ICA 800V Specifications ICA 2400V Specifications Page Peavey Electronics Corporation Limited Warranty Important Safety Instructions 80304800