Peavey ICA 2400V, ICA Series, ICA 800V, ICA 400V, ICA 1200 manual ICA 600 Specifications

Page 40

ICA600 SPECIFICATIONS

Rated Power (2 X 4 ohms):

Slew Rate:

Cooling:

300 watts @ 20 Hz - 20 kHz, both

30 V/µs

80 mm DC fan, off until heatsinks

channels driven at < 0.1% THD

 

reach 45° C, then variable speed

 

Damping Factor (8 ohms):

 

Rated Power (2 x 8 ohms):

>450:1 @ 20 Hz - 1 kHz

Controls:

200 watts @ 20 Hz - 20 kHz at

 

2 rear panel attenuators, sequential

< 0.05% THD

Input CMRR:

turn-on / off

 

>-65 dB @ 1 kHz

 

Rated Power (1 x 4 ohms):

 

Indicator LEDs:

360 watts @ 1 kHz at < 0.015% THD

Voltage Gain:

2 Clip, 2 Signal, 2 LFC, 1 Protect,

 

x40 (32 dB)

1 Power

Rated Power (1 x 8 ohms):

 

 

275 watts @ 1 kHz at < 0.005%

Input Sensitivity:

Protection:

THD

.866 volts @ 4 ohms, 1 volt @

Temp., DC, turn-on bursts, subsonic,

 

8 ohms

incorrect load or short

Minimum Load Impedance:

 

 

4 ohms

Input Impedance:

Connectors:

 

20 k ohms, balanced

8-pin plugable signal input, 4-pin

Maximum RMS Voltage Swing:

 

plugable sequential power,

57 volts

Hum and Noise:

4-terminal barrier strip, IEC AC

 

>-108 dB, “A” weighted referenced

power connector

Frequency Response:

to rated power @ 8 ohms

 

10 Hz - 25 kHz; +0, -3 dB at 1 watt

 

Construction:

 

Crosstalk:

All steel; 16 ga. chassis, 18 ga. top,

Power Bandwidth:

>-75 dB, “A” weighted referenced to

12 ga. rack ears

10 Hz - 100 kHz; +0, -3 dB at rated

rated power @ 8 ohms

 

power

 

Dimensions:

 

Current Draw @ 1/8 power:

3.48" x 19" x 16.4"

THD (2 x 4 ohms):

670 watts @ 4 ohms, 460 watts @

88.4 mm x 483 mm x 416.6 mm

<0.1% @ 300 W from 20 Hz - 20 kHz

8 ohms

 

with both channels driven

 

Gross Weight:

 

Current Draw @ 1/3 power:

33.6 lbs. (15.25 kg)

THD (2 x 8 ohms):

1,055 watts @ 4 ohms, 650 watts @

 

<0.05% @ 200 W from 20 Hz -

8 ohms

Net Weight:

20 kHz with both channels driven

 

30.2 lbs. (13.7 kg)

 

Idle Current Draw:

 

THD (1 x 4 ohms):

30 watts in Standby Mode

 

<0.01% @ 350 W @ 1 kHz

 

 

 

Maximum Current Draw:

 

THD (1 x 8 ohms):

1,622 watts @ 4 ohms, 1,010 watts

 

<0.005% @ 275 W @ 1 kHz

@ 8 ohms

 

SMPTE IMD:

Thermal Emissions (BTU/hr.):

 

<0.1% 60 Hz and 7 kHz, 300 W @

625 @ 1/3 power 4 ohms,

 

4 ohms

500 @ 1/3 power 8 ohms,

 

 

395 @ 1/8 power 4 ohms,

 

 

350 @ 1/8 power 8 ohms

 

Due to our efforts for constant improvements, features and specifications are subject to change without notice.

40

Image 40
Contents A S E R I E S Page Table of Contents Installation and Mounting Basic SetupIntroduction UnpackingFront Panel Features Position AC Power SwitchPower LED Signal LEDBack Panel Features Input Section IEC Power ConnectorSequential TURN-ON Connector Output Barrier StripOperation Signal Mode Configuration Stereo Mode Connection Diagram Parallel Mode DiagramProtection Features Sequential TURN-ON / TURN-OFF FADE-IN ProtectionThermal Protection Short CircuitWire Gauge Chart ICA 600 Specifications Rated Power 2 X 4 ohms Slew Rate CoolingICA 1200 Specifications Gross Weight 51.4 lbs .3 kg Net WeightICA 2400 Specifications ICA 400V Specifications THD two channels driven ICAICA 800V Specifications ICA 2400V Specifications Introducción DesempacarInstalación Y Montura Instalación BásicaInterruptor DE Poder AC Power DE Tres Posiciones Características DEL Panel FrontalInstalador Para Rack LED DE PoderSección DE Entrada Características DEL Panel TraseroConectores DE Salida DE Para Cables Operación Diagrama DE Modo Estéreo Diagrama DE Modo Paralelo Diagrama DE Modo Puenteado Conexiones DE Salida DE BocinasConexión DE Tierra Características DE ProtecciónProtección DE FADE-IN Protección TérmicaCorto Circuito Protección DE Voltaje DE CDFicha DE Medidas DE Cables Especificaciones del ICA Razón de Slew Topología Especificaciones del ICA 400V Poder Medido dos canales THD Distorsión Total Armónica dos canales Deballage InstallationMise EN Route LED DE Signal Panneau AvantPattes DE Fixation Rack Interrupteur 3-POSITIONS D’ALIMENTATIONPanneau Arriere EntreesSorties Connecteur D’ALIMENTATION IECConfiguration DU Signal D’ENTREE Alimentation ElectriqueRefroidissement Emissions ThermiquesStereo Mode Connection Diagram Parallel Mode Diagram Masse DU Signal Systemes DE Protection Connexions HAUTS-PARLEUR Clip LimiteurMise EN ROUTE/ARRET Sequentiels Protection DE Mise EN RouteProtection Thermale Protection DE Court CircuitStranded Power ICA 600 Specifications ICA 1200 Specifications ICA 2400 Specifications ICA 400V Specifications ICA 800V Specifications Input Cmrr Rated Power one channel Einleitung AuspackenEinbau UND Anschluss Erste SchrittePOWER-LED SIGNAL-LEDVorderseite Montagezubehör FÜR DEN RACK-EINBAULFC-LED PROTECT-LEDRückseite EingangsmodulBedienung Betriebsarten WärmeentwicklungSTEREO-BETRIEB Signalerdung PARALLEL-BETRIEBBrückenbetrieb LautsprecheranschlussCLIP-LIMITER LastfehlerkorrekturEinschaltverzögerung ÜberhitzungsschutzVerkabelung Sequentielle Ein/Ausschalt-Funktion Wire Gauge Chart ICA 600 Specifications ICA 1200 Specifications ICA 2400 Specifications ICA 400V Specifications ICA 800V Specifications ICA 2400V Specifications Page Peavey Electronics Corporation Limited Warranty Important Safety Instructions 80304800