Peavey ICA 800V, ICA Series, ICA 600, ICA 2400, ICA 400V, ICA 1200 Input Cmrr Rated Power one channel

Page 45

ICA2400V SPECIFICATIONS

Rated Power (two channels):

Damping Factor:

Cooling:

1200 watts @ 20 Hz to 20 kHz both

>250:1 @ 20 Hz – 1 kHz

120 mm DC fan, off until heatsinks

channels driven at < 0.1% THD

 

reach 45° C, then variable speed

 

Input CMRR:

 

Rated Power (one channel):

>65 dB @ 1 kHz

Controls:

Awaiting test results

 

2 rear panel attenuators, sequential

 

Voltage Gain:

turn-on /-off:

Topology:

x 40 (32 dB)

 

Class H

 

Indicator LEDs :

 

Input Sensitivity:

2 Clip, 2 Signal, 2 LFC, 1 Protect,

Minimum Load Impedance:

1.77 volts

1 Power

@ 70.7 volts

 

 

6.3 ohms

Input Impedance:

Protection:

 

20 k ohms, balanced

Temp., DC, turn-on bursts, subsonic,

Maximum RMS Voltage Swing:

 

incorrect load or short

95 volts

Hum and Noise:

 

 

>-115 dB, “A” weighted referenced to

Connectors:

Frequency Response:

rated power

8-pin plugable signal input, 4-pin

10 Hz – 25 kHz; +0, -.3 dB at 1 watt

 

plugable sequential power, 4-terminal

 

Crosstalk:

barrier strip, IEC AC power connector

Power Bandwidth:

> -55 dB, “A” weighted referenced to

 

10 Hz – 50 kHz; +0, -3 dB at rated

rated power

Construction:

power

 

All steel; 16 ga. chassis, 18 ga. top,

 

Current Draw @ 1/8 power:

12 ga. rack ears

THD (two channels driven):

497 watts

 

<0.008% @ 800 W @ 1 kHz with both

 

Dimensions:

channels driven

Current Draw @ 1/3 power:

5.23" x 19" x 16.4"

 

1037 watts

133 mm x 483 mm x 416mm

THD (one channel driven):

 

 

<0.006% @ 830 W @ 1 kHz

Idle Current Draw:

Gross Weight:

 

35 VA in Standby Mode

51.4 lbs. (23.3 kg.)

SMPTE IMD:

 

 

<0.1% 60 Hz and 7 kHz, 800 W @

Maximum Current Draw:

Net Weight:

8 ohms

2,760 VA (time limited by breaker)

45 lbs. (20.4 kg.)

Slew Rate:

Thermal Emissions (BTU/hr.):

 

35 V/us

940 @ 1/8 power,

 

 

1,830 @ 1/3 power

 

Due to our efforts for constant improvements, features and specifications are subject to change without notice.

45

Image 45
Contents A S E R I E S Page Table of Contents Basic Setup Installation and MountingIntroduction UnpackingPosition AC Power Switch Front Panel FeaturesPower LED Signal LEDIEC Power Connector Back Panel Features Input SectionSequential TURN-ON Connector Output Barrier StripOperation Stereo Mode Connection Diagram Parallel Mode Diagram Signal Mode ConfigurationProtection Features FADE-IN Protection Sequential TURN-ON / TURN-OFFThermal Protection Short CircuitWire Gauge Chart Rated Power 2 X 4 ohms Slew Rate Cooling ICA 600 SpecificationsGross Weight 51.4 lbs .3 kg Net Weight ICA 1200 SpecificationsICA 2400 Specifications THD two channels driven ICA ICA 400V SpecificationsICA 800V Specifications ICA 2400V Specifications Desempacar IntroducciónInstalación Y Montura Instalación BásicaCaracterísticas DEL Panel Frontal Interruptor DE Poder AC Power DE Tres PosicionesInstalador Para Rack LED DE PoderCaracterísticas DEL Panel Trasero Sección DE EntradaConectores DE Salida DE Para Cables Operación Diagrama DE Modo Estéreo Diagrama DE Modo Paralelo Conexiones DE Salida DE Bocinas Diagrama DE Modo PuenteadoConexión DE Tierra Características DE ProtecciónProtección Térmica Protección DE FADE-INCorto Circuito Protección DE Voltaje DE CDFicha DE Medidas DE Cables Especificaciones del ICA Razón de Slew Topología Especificaciones del ICA 400V Poder Medido dos canales THD Distorsión Total Armónica dos canales Installation DeballageMise EN Route Panneau Avant LED DE SignalPattes DE Fixation Rack Interrupteur 3-POSITIONS D’ALIMENTATIONEntrees Panneau ArriereSorties Connecteur D’ALIMENTATION IECAlimentation Electrique Configuration DU Signal D’ENTREERefroidissement Emissions ThermiquesStereo Mode Connection Diagram Parallel Mode Diagram Systemes DE Protection Masse DU SignalConnexions HAUTS-PARLEUR Clip LimiteurProtection DE Mise EN Route Mise EN ROUTE/ARRET SequentielsProtection Thermale Protection DE Court CircuitStranded Power ICA 600 Specifications ICA 1200 Specifications ICA 2400 Specifications ICA 400V Specifications ICA 800V Specifications Input Cmrr Rated Power one channel Auspacken EinleitungEinbau UND Anschluss Erste SchritteSIGNAL-LED POWER-LEDVorderseite Montagezubehör FÜR DEN RACK-EINBAUPROTECT-LED LFC-LEDRückseite EingangsmodulBedienung Wärmeentwicklung BetriebsartenSTEREO-BETRIEB PARALLEL-BETRIEB SignalerdungBrückenbetrieb LautsprecheranschlussLastfehlerkorrektur CLIP-LIMITEREinschaltverzögerung ÜberhitzungsschutzVerkabelung Sequentielle Ein/Ausschalt-Funktion Wire Gauge Chart ICA 600 Specifications ICA 1200 Specifications ICA 2400 Specifications ICA 400V Specifications ICA 800V Specifications ICA 2400V Specifications Page Peavey Electronics Corporation Limited Warranty Important Safety Instructions 80304800