Korg CX-3 Amp Type Type 1, Type 2, Pre Amp, Amp Gain, Tone Treble 10...+10, Tone Middle 10...+10

Page 23

Parameters

Group 4

Amp Type

[Type 1, Type 2, Pre Amp]

Select the type of amp.

 

Type 1: A standard powered amp for organ, produc- ing a mild and fat tone.

Type 2: This emphasizes the high range more than Type 1, producing an uncolored tone.

Pre Amp: The pre-amp will be used. This is the sound of a direct line-out from the organ.

If you select Type 1 or Type 2, using the front panel ROTARY section [ON] key to turn the rotary speaker on will simulate using a rotary speaker. If you turn this off, a standard speaker will be simulated.

If you select Pre Amp, the powered amp and rotary speaker will not be used; the sound will be that of a line-out connection from the organ itself.

Amp Gain

[0...99]

Adjust the gain (amplification) when the “Amp Type” parameter is set to Type 1 or Type 2.

With high settings of this value, the sound will be distorted more severely when expression/overdrive is raised.

This setting will not be used if the “Amp Type” parameter is set to Pre Amp.

Tone Treble

[–10...+10]

Adjust the high frequency range of the amp selected

by the “Amp Type” parameter.

 

Tone Middle

[–10...+10]

The mid-frequency range of the amp selected by the

“Amp Type” parameter.

 

Tone Bass

[–10...+10]

Adjust the low frequency range of the amp selected by the “Amp Type” parameter.

Amp Type: Amp 1 or Amp 2

Pre Amp

Amp 1/2

Reverb

Rotary

Group 4: Amp Gain

Tone TrebelGroup 5: Rev Routing

Tone Middle

Tone Bass

Amp Type: Pre Amp

Pre Amp Reverb

Group 4: Tone Trebel

Tone Middle

Tone Bass

Group 5

Reverb Type

[Room, Hall, Plate]

Select the type of reverb.

 

Reverb Time

[00.25...16.00 (Sec)]

Adjust the reverb time.

 

The range in which the reverb time can be set will depend on what is selected for the “Reverb Type” parameter.

Reverb Mix Level

[0...99]

Adjust the amount of reverb.

 

Rev Routing (Reverb Routing)

[Rot->Rev, Rev->Rot]

Specify whether the reverb will be placed before or after the rotary speaker.

Rot -> Rev: The reverb effect will be applied after the rotary speaker.

Rev -> Rot: The reverb effect will be applied before the rotary speaker.

This setting is not used if the “Amp Type” parameter is set to Pre Amp.

Group 6

These settings are not used if the “Amp Type” parameter is set to Pre Amp.

Horn: 0 Rotor: 100 (Rotary Horn/Rotor Balance) [0:100...100:0]

Adjust the volume balance between the horn and the rotor of the rotary speaker.

Horn Slow Speed

[0...99]

Adjust the slow rotational speed of the horn.

 

Horn Fast Speed

[0...99]

Adjust the fast rotational speed of the horn.

 

Rotor Slow Speed

[0...99]

Adjust the slow rotational speed of the rotor.

 

Rotor Fast Speed

[0...99]

Adjust the fast rotational speed of the horn.

 

Horn Up Transit (Horn Up Transition)

[0...99]

Adjust the time over which the horn rotation changes

from slow to fast.

 

Horn Down Transit (Horn Down Transition)

[0...99]

Adjust the time over which the horn rotation changes from fast to slow.

Horn Stop Transit (Horn Stop Transition)

[0...99]

Adjust the time over which the horn rotation actually

comes to a stop after you stop the rotation.

 

Horn Strt Transit (Horn Start Transition)

[0...99]

Adjust the time over which the horn reaches the speci- fied speed after it begins to rotate.

19

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Page CE mark for European Harmonized Standards FCC Regulation Warning for U.S.ADisplay screen MIDI-related conventions SymbolKeys and knobs ParametersContents About the CX Main featuresNormal mode EX modeFront panel Controls and their functionsGlobal key Rotary section Rear panel Midi in connectorConnections Power cable connectionsShortcut Switching the displayDisplay screen Drawbar levels and iconsHow a program is organized Play using the drawbarsAbout programs Playing the CX-3Try selecting other programs Press the EX Mode key to enter EX modePlay the keyboard Select a program in Normal modeSelect a program in EX mode Dividing the keyboard into left and right When performing with the drawbarsWhen playing a program Applying effects to your performanceRotary speaker Key settings of the Percussion sectionVibrato and chorus Overdrive Key settings of the Rotary section ReverbListening to the demo songs Other effectsCopying drawbar parameters Editing a programEditing the drawbar parameters Press the or + key to select Vintage Parameters unique to a combo organOther editing Writing a programCopying a program Writing global settingsReturning a program to the factory settings Over Tone Level Wheel Type Vintage, CleanGroup Output Level 127Perc Nrml Level Percussion Normal Level EX Mode Drawbar LevelDB Preset’s Perc Drawbar Preset Percussion Dis, Ena EX Drawbar TypeTone Middle 10...+10 Amp Type Type 1, Type 2, Pre AmpAmp Gain Tone Treble 10...+10Rotor Strt Transit Rotor Start Transition Rotor Up Transit Rotor Up TransitionRotor Down Transit Rotor Down Transition Rotor Stop Transit Rotor Stop TransitionRename Amp Gain Ctrl Min AMP Gain Control RangeAmp Gain Ctrl Max AMP Gain Control Range Rev Mix Ctrl Max Reverb Mix Control RangeExp Minimum Level Expression Minimum Level Global modeMaster Tune 430.0Hz...+450.0Hz Transpose 12...+12Midi Lower 2nd Ch Midi Transmit Channel Lower 2nd Midi Global Ch Midi Global ChannelMidi Upper Rx Ch Midi Receive Channel Upper Midi Upper 2nd Ch Midi Transmit Channel Upper 2nd 16, OffCC# DB2-3 Midi Control Change Assign for Drawbar CC# Lower DB Sel Midi Control Change Assign forLower Drawbar Select 31, 33...95, Off CC# DB2-1 Midi Control Change Assign for DrawbarSwap Swap Program CC# Rotary Fast Midi Control Change Assign forProgram Mapper Copy Copy One ProgramDump Global Dump Global Parameter Default DB Select Drfault Drawbar SelectDump Program Dump One Program Dump Program All Dump All ProgramsAbout Midi Connecting an external Midi sequencer or computerHow the drawbars work Midi applicationsTransmission Midi data dumpChanging the program / bank ReceptionReceiving a data dump If you wish to execute the dump, press the WRITE/ENTER keyUniversal system exclusive To reset all controllersTransmitting sound settings and other data Data Dump To silence all notesDemo song names Normal mode programsEX mode programs Voice name listTroubleshooting Cable storage Specifications and optionsFortissimo function Selectable pedal angleFunction Transmitted Recognized Remarks Midi implementation chartIndex Korg INC
Related manuals
Manual 5 pages 26.43 Kb Manual 4 pages 38.2 Kb
Top Page Image Contents