Parameters
Group 4: Amp
Amp Type | [Type 1, Type 2, Pre Amp] |
here you can select the amp type.
Type 1: This is a conventional organ power amp. It produces a mild and fat sound.
Type 2: Compared to Type 1, this emphasizes the high range, and produces a more uncolored sound.
Pre Amp: Use a pre amp. This is the sound of the organ's
When Type 1 or Type 2 are selected: When the front panel ROTARY [ON] key is used to turn on the rotary speaker, the effect of the rotary speaker will be simulated. When this is turned off, a conventional speaker will be simulated.
When Pre Amp is selected: The power amp and rotary speaker will not be used, and the sound will be as if it were taken from the preamp
Spkr Simulator (Speaker Simulator) | [On, Off] |
When the “Amp Type” parameter is set to Type 1 or Type 2, this turns the amp simulator function on or off.
Amp Gain | [0...99] |
Adjusts the gain (amplification) when the “Amp Type” parameter is set to Type 1 or Type 2.
With high settings of this value, the sound will distort more severely when the expression/overdrive is raised.
This setting will not apply if the “Amp Type” parameter is set to Pre Amp.
Tone Treble |
Adjusts the high frequency level of the amp selected by the “Amp Type” parameter.
Tone Middle |
Adjusts the
Tone Bass |
|
Adjusts the low frequency level of the amp selected by the “Amp Type” parameter.
|
|
|
|
| |
Amp Type: Amp 1 or Amp 2 |
|
|
|
| |
Pre Amp | Amp 1 | Speaker |
| Reverb | Rotary |
or |
| ||||
| Amp 2 |
|
|
|
|
Group 4: Amp Gain | Group 4: Spkr Simulator | Group 5: Rev Routing | |||
| Tone Trebel |
|
| ||
|
|
|
|
| |
| Tone Middle |
|
|
|
|
| Tone Bass |
|
|
|
|
Amp Type: Pre Amp |
|
|
|
| |
Pre Amp |
|
| Reverb |
| |
Group 4: Tone Trebel |
|
|
|
|
|
Tone Middle |
|
|
|
| |
Tone Bass |
|
|
|
|
|
Group 5: Reverb
Reverb Type | [Room, Hall, Plate, Dark] |
Selects the type of reverb. |
|
Reverb Time | [00.25...16.00 (Sec)] |
Specifies the reverb time. |
|
The range in which the reverb time can be adjusted will depend on your selection for the “Reverb Type” parameter.
Reverb Mix Level | [0...99] |
Specifies the amount of reverb signal that is mixed with the original sound.
Rev Routing (Reverb Routing) [Rot->Rev, Rev->Rot]
Selects whether the reverb will be applied before the rotary speaker or after it.
This setting will not be used if the “Amp Type” parameter is set to Pre Amp.
Group 6: Rotary Effect
These settings will not be used if the “Amp Type” parameter is set to Pre Amp.
Horn: 0 Rotor: 100 (Rotary Horn/Rotor Balance) [0:100...100:0]
Adjuststhe volume balance between the horn and rotor of the rotary speaker.
Horn Slow Speed | [0...99] |
Specifies the rotational speed of the horn during slow rotation.
Horn Fast Speed | [0...99] |
Specifies the rotational speed of the horn during fast rotation.
Rotor Slow Speed | [0...99] |
Specifies the rotational speed of the rotor during slow rotation.
Rotor Fast Speed | [0...99] |
Specifies the rotational speed of the rotor during fast rotation.
Horn Up Transit (Horn Up Transition) | [0...99] |
Specifies the time over which the horn will change from slow to fast rotation.
Horn Down Transit (Horn Down Transition) | [0...99] |
Specifies the time over which the horn will change from fast to slow rotation.
Horn Stop Transit (Horn Stop Transition) | [0...99] |
Specifies the time it will take for the horn to actually come to rest after rotation is switched off.
Horn Strt Transit (Horn Start Transition) | [0...99] |
Specifies the time it will take for the horn to reach the specified speed after rotation is switched on.
26