Korg BX-3 manual Wheel Brk Pedal Wheel Brake Pedal Mode Momnt, Alter

Page 28

Parameters

Hold Uppr Ctrl (Hold Upper Controller)

[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]

This is displayed in Normal Edit mode.

Pedal 1: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 jack will switch Hold on/off for the notes played on the keyboard that controls the UPPER tone generator.

Pedal 2: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 2 jack will perform the above operation.

Off: No function.

Hold Lowr Ctrl (Hold Lower Controller)

[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]

This is displayed in Normal Edit mode.

Pedal 1: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 jack will switch Hold on/off for the notes played on the keyboard that controls the LOWER tone generator.

Pedal 2: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 2 jack will perform the above operation.

Off: No function.

Wheel Brk Ctrl (Wheel Brake Controller)

[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]

This is displayed in Normal Edit mode.

Pedal 1: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 jack will switch the “Wheel Brake” parameter (Global mode Group 7) on/off.

Pedal 2: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 2 jack will perform the above operation.

Off: No function.

Wheel Brk Pedal (Wheel Brake Pedal Mode)

[Momnt, Alter]

Select the on/off operation of the pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 or 2 jack.

Momnt: The pitch will gradually fall as long as you continue pressing the pedal switch. When you release the pedal switch, the pitch will gradually rise to the normal state.

Alter: The pitch will begin falling once you press the pedal switch. When you press it once again, the pitch will gradually rise to the normal state.

Rtry FAST Ctrl (Rotary FAST Controller)

[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]

Pedal 1: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 jack will turn the ROTARY [FAST] key on/off.

Pedal 2: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 2 jack will perform the above operation.

Off: No function.

Rtry FAST Pedal (Rotary FAST Pedal Mode)

[Momnt, Alter]

Select the on/off operation of the pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 or 2 jack. The pedal switch will have the same function as pressing the front panel ROTARY [FAST] key.

Momnt: The rotary speed will gradually increase as long as you continue pressing the pedal switch, until it reaches the speed specified by the Group 6 “Rotor Fast Speed” parameter. When you release the pedal switch, the rotary speed will gradually decrease until it reaches the speed specified by the Group 6 “Rotor Slow Speed” parameter. Alter: Once you press the pedal switch, the rotary speed will gradually increase until it reaches the speed specified by the Group 6 “Rotor Fast Speed” parameter. When you press the pedal switch once again, the rotary speed will gradually decrease until it reaches the speed specified by the Group 6 “Rotor Slow Speed” parameter.

Rtry STOP Ctrl (Rotary STOP Controller)

[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]

Pedal 1: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 jack will turn the ROTARY [STOP] key on/off.

Pedal 2: A pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 2 jack will perform the above operation.

Off: No function.

Rtry STOP Pedal (Rotary STOP Pedal Mode)

[Momnt, Alter]

Select the on/off operation of the pedal switch etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 or 2 jack. The pedal switch will have the same function as pressing the front panel ROTARY [STOP] key.

Momnt: The rotary speed will gradually slow down and then stop as long as you continue pressing the pedal switch.

Alter: Once you press the pedal switch, the rotary speed will gradually slow down and then stop.

Amp Gain Ctrl (Amp Gain Controller)

[Off, Pedal 1/(Pdl 1)*, Pedal 2/(Pdl 2)*]

Pedal 1: An expression pedal etc. connected to the rear panel ASSIGNABLE PEDAL/SW 1 jack will control the Group 4 “Amp Gain” parameter of Normal Edit mode and EX Edit mode.

Pedal 2: An expression pedal etc. connected to the rear panel ASSIGNABLE PEDAL/SW 2 jack will perform the above operation.

Off: No function.

 

* (Pdl 1), (Pdl 2): These indicate that Pedal 1 or Pedal 2 are selected for the Global mode Group 1 “Prog Up Ctrl” or “Prog Down Ctrl” parameters. With these settings, the settings of

28

Global mode are used, and the settings you made here will be ignored. However if you select another value in Global mode, the display here will change from (Pdl 1) to Pedal 1 or

from (Pdl 2) to Pedal 2, and you will be able to operate the corresponding function from the pedal switch.

 

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Page FCC Regulation Warning for U.S.A CE mark for European Harmonized StandardsHow this manual is organized, and how to use it Printing conventions in this manualTable of Contents Main features Normal modeEX mode About the BXParts of the BX-3 and what they do Front panelEX Mode key Display keyEdit key Global keyDrawbar Select section Pitch Bend wheel, Modulation wheelPitch Bend wheel Modulation wheelRear panel Power cable connections ConnectionsOutput jack connections Pedal connectionsNormal mode Playing using the Program’s drawbar settingsSelecting a program PlayingEX mode Using the Drawbar 1 and 2 settingsFrom Normal mode, press the EX Mode key Lets try selecting a programEX Drawbars EX PercussionPlay the lower keyboard Selecting a different programSwitching the display Normal modeEX mode About the displayShortcuts Global modePercussion icon Restoring the factory settings About the programsHow a program is structured Initializing one programNormal mode Checking the DB Presets Perc parameterPercussion Initializing the Global parametersRotary EX modeEX Percussion in Drawbar Effects Saving your dataUse the + keys to select the desired setting EditingMidi data dump Editing the soundCopying drawbar parameters Editing the drawbar parametersOther parameters Copying a program Swapping two programsEditing the name of a program Press the WRITE/ENTER key, and then press + key onceUse the -+ keys to specify the desired charac- ter Group 1 Basic Character Group 2 DrawbarGroup 3 Percussion Group 5 Reverb Group 4 AmpGroup 6 Rotary Effect Group 7 Controller Rtry Fast Pedal Rotary Fast Pedal Mode Momnt, Alter Wheel Brk Pedal Wheel Brake Pedal Mode Momnt, AlterRtry Stop Pedal Rotary Stop Pedal Mode Momnt, Alter Group 8 Program Name Global mode Group 1 BasicGroup 2 Midi Channel Group 3 Midi ParametersGroup 4 Midi CC# Group 5 Midi CC# Group 6 Ex Drawbar Set Group 7 UtilityGroup 8 Demo Exp Pdl Calibration Expression Pedal CalibrationWheel Brake on Demo PlayHow the drawbars work Connecting an external Midi sequencer or computerAbout Midi Press the Program 7 key, and then press the key twice TransmissionSelect the data that you want to dump Reception Type of data Data sizeTo reset all controllers Transmitting sound settings and other data Data DumpChanging the program / bank To silence all notesNormal mode programs EX mode programsVoice name list Demo song namesTroubleshooting Fortissimo function Cable storageSelectable pedal angle To select pedal angleSpecifications and options Assembling the stand Assemblage du pupitreLightly attach the rear braces to the side panel R Attach the center braceFixer légèrement les supports arrière au panneau latéral D Mettre le support central en placeCheck after assembly Other cautionsVérification après montage Autres précautions à prendreMidi implementation chart
Top Page Image Contents