Parameters
Prog Up Ctrl (Program Up Controller)
[Off, Pedal 1/(Pdl 1), Pedal 2/(Pdl 2)]
Pedal 1: The pedal switch connected to the rear panel ASSIGNABLE PEDAL/SW 1 jack will switch programs. Each time you operate the pedal switch, the program number will be increased by 1.
Pedal 2: The pedal switch connected to the rear panel ASSIGNABLE PEDAL/SW 2 jack will perform the function described above.
Off: No function
(Pdl 1), (Pdl 2): Indicates that this pedal switch is already selected for the following “Prog Down Ctrl” parameter. Please select a different pedal switch.
If the same pedal switch is selected for a parameter in Normal Edit mode or EX Edit mode as well as for this Global parameter, this Prog Up Ctrl setting will be used, and the setting in Normal Edit mode or EX Edit mode will be ignored.
Prog Down Ctrl (Program Down Controller)
[Off, Pedal 1/(Pdl 1), Pedal 2/(Pdl 2)]
Pedal 1: The pedal switch connected to the rear panel ASSIGNABLE PEDAL/SW 1 jack will switch programs. Each time you operate the pedal switch, the program number will be decreased by 1.
Pedal 2: The pedal switch connected to the rear panel ASSIGNABLE PEDAL/SW 2 jack will perform the function described above.
Off: No function
(Pdl 1), (Pdl 2): Indicates that this pedal switch is already selected for the above “Prog Up Ctrl” parameter. Please select a different pedal switch.
If the same pedal switch is selected for a parameter in Normal Edit mode or EX Edit mode as well as for this Global parameter, this Prog Down Ctrl setting will be used, and the setting in Normal Edit mode or EX Edit mode will be ignored.
Pedal 1 Sw Polarity (Pedal 1 Switch Polarity) | |
Pedal 2 Sw Polarity (Pedal 2 Switch Polarity) |
Set these parameters to match the polarity of the pedal switches connected to the rear panel ASSIGNABLE PEDAL/SW 1 and 2 jacks. If these settings do not match the actual polarity of the pedal switches, the pedal switches will not operate correctly.
For example, the separately sold
Group 2: MIDI Channel
MIDI Global ch (MIDI Global Ch) | [1...16] |
Specifies the global MIDI channel that will be used to transmit and receive MIDI. (The factory setting is 1.)
MIDI Upper Rx ch (MIDI Upper Receive Channel) [1...16, Off]
Specifies the MIDI channel on which the UPPER key- board will receive MIDI note messages. (The factory setting is channel 1.)
MIDI Upper Tx ch (MIDI Upper Transmit Channel) [1...16, Off]
Specifies the channel on which the UPPER keyboard will transmit MIDI note messages with a fixed velocity value. (The factory setting is channel 1.) The velocity value is set by “MIDI Fixed Velcty.”
MIDI Upper 2nd ch (MIDI Upper 2nd Transmit
Channel) | [1...16, Off] |
Specifies the channel on which the UPPER keyboard will transmit MIDI note messages with a variable velocity. (The factory setting is Off.)
Off: Messages will not be transmitted. Be sure to turn this Off unless you are using a MIDI sound module that requires variable velocity (such as a piano module).
If you specify a MIDI channel for this parameter and are using a MIDI sound module etc. connected to the
MIDI Lower Rx ch (MIDI Lower Receive Channel) [1...16]
Specifies the MIDI channel on which the LOWER key- board will receive MIDI note messages. (The factory setting is 2.)
MIDI Lower Tx ch (MIDI Lower Transmit Channel) [1...16, Off]
Specifies the channel on which the LOWER keyboard will transmit MIDI note messages with a fixed velocity value. (The factory setting is channel 2.) The velocity value is set by “MIDI Fixed Velcty.”
MIDI Lower 2nd ch (MIDI Lower 2nd Transmit
Channel) | [1...16, Off] |
Specifies the channel on which the LOWER keyboard will transmit MIDI note messages with a variable velocity. (The factory setting is Off.)
Off: Messages will not be transmitted. Be sure to turn this Off unless you are using a MIDI sound module that requires variable velocity (such as a piano module).
If you specify a MIDI channel for this parameter and are using a MIDI sound module etc. connected to the
Group 3: MIDI Parameters
MIDI Fixed Velcty (MIDI Fixed Velocity) | [0...127] |
Specifies the velocity value of the MIDI note messages that are transmitted with fixed velocity. (The factory setting is 80.)
MIDI Rx Prg Chng (MIDI Receive Program Change) [Dis, Ena]
Dis (Disable): MIDI program changes received on the global MIDI channel will be ignored.
Ena (Enable): The
MIDI Prog Mapper (MIDI Program Mapper) [Dis, Ena]
Dis (Disable): The program mapper will not be used when transmitting or receiving MIDI program changes. Ena (Enable): The program mapper will be used when transmitting or receiving MIDI program changes. (The factory setting is Ena.)
MIDI Rx Sys Exc (MIDI Receive System Exclusive) [Dis, Ena]
Dis (Disable): Incoming system exclusive data will be ignored. (The factory setting is Dis.)
Ena (Enable): Incoming system exclusive data will be received.
31