Hampton Direct U32-LP2, U32-NG2 Maintenance Instructions, Copy of Lighting Instruction Plate

Page 18

OPERATING INSTRUCTIONS

Blower Thermodisc:

When this thermally activated switch turns ON it will create a small "clicking" sound. This is the switch contacts closing and is normal.

Pilot Flame:

While the pilot flame is on it can make a very slight "whisper" sound.

Gas Control Valve:

As the gas control valve turns ON and OFF, a dull clicking sound may be audible, this is normal operation of a gas regulator or valve.

Unit Body/Firebox:

Different types and thicknesses of steel will expand and contract at different rates result- ing in some "cracking" and "ticking" sounds will be heard throughout the cycling process.

MAINTENANCE

INSTRUCTIONS

1)

Always turn the gas valve to off before

 

cleaning. For relighting, refer to lighting

 

instructions. Keep the burner and control

 

compartment clean by brushing and vac-

 

uuming at least once a year. When cleaning

 

the logs, use a clean soft paint brush as the

 

logs are fragile and easily damaged.

2) Clean (never when unit is hot) appliance,

 

door and louvers with a damp cloth. Never

 

use an abrasive cleaner. The gold louvers

 

(and optional gold door) may be scratched

 

if abrasives are used to clean them.

 

The heater is finished in a heat resistant

 

paint and should only be refinished with

 

heat resistant paint (not with wall paint).

 

FPI uses StoveBrite Paint - Metallic Black

 

#6309.

3)

Make a periodic check of burner for proper

 

position and condition. Visually check the

 

flame of the burner periodically, making

 

sure the flames are steady; not lifting or

COPY OF LIGHTING INSTRUCTION PLATE

FOR YOUR SAFETY READ BEFORE LIGHTING

This appliance must be installed in accordance with local codes, if any; if not,

follow the current CAN1-B149/ANSI Z 223.1 (Australia: AG601, New Zealand: NZS 5261)

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or gas supplier.

A) This appliance has a pilot which must be lighted

a qualified service technician. Force or attempted

by hand, following the instructions below

repair may result in a fire or explosion.

 

exactly.

 

 

 

 

D) Do not use this appliance if any part has been under

B) BEFORE LIGHTING smell all around the appliance

water. Immediately call a qualified service techni-

area for gas. Be sure to smell next to the floor

cian to inspect the appliance and to replace any part

because some gas is heavier than air and will

of the control system and any gas control which has

settle on the floor.

 

 

been under water.

 

WHAT TO DO IF YOU SMELL GAS

This appliance needs fresh air for safe operation and

- Do not try to light any appliance

must be installed so there are provisions for adequate

- Do not touch any electric switch, do not use any

combustion and

ventilation air.

 

phone in your building

 

CAUTION: Hot while in operation. Do not touch.

- Immediately call your gas supplier from a

neighbors phone. Follow the gas supplier’s in-

Severe Burns may result. Due to high surface

structions.

 

 

 

 

temperatures keep children, clothing and

- If you cannot reach your gas supplier, call the furniture, gasoline and other liquids having

fire department.

 

 

fammablevaporsaway.Keepburnerandcontrol

C) Use only your hand to push in or turn the gas compartment

clean. See installation and

control knob. Never use tools. If the knob will not

operatinginstructionsaccompanyingappliance.

push in or turn by hand, don’t try to repair it, call

 

 

 

 

 

 

 

LIGHTING INSTRUCTIONS

 

 

STOP! Read the safety information above on this

Release knob and it will pop back up. Pilot should

label.

 

 

 

 

remain lit. If it goes out, repeat steps 3) and 4).

1) Push in gas control knob slightly and turn

If knob does not pop up when released, stop and

clockwise

to “OFF”. Knob cannot be turned

immediately call your service technician or gas

from “PILOT” to “OFF” unless knob is pushed in

supplier.

 

 

slightly. Do

not

force.

 

 

If the pilot will not stay lit after several tries, turn the

2) Wait five (5) minutes to clear out any gas. If you

gas control knob to “OFF” and call your service

then smell gas STOP! follow “B” in the safety

technician or gas supplier.

 

information above on this label. If you don’t smell

5) Turn gas control knob counterclockwise

to “ON”.

gas, go to the next step.

 

6) Use rocker switch to operate main burner.

3) Turn knob

on

gas

control

counterclockwise

PILOT BURNER

 

 

to “PILOT”.

 

 

 

 

VEILLEUSE

 

OFF

4) Push in control

knob

all the

way and hold in.

THERMOPILE

 

 

Immediately push black button on spark igniter

 

 

ELEMENT

 

 

until pilot lights. Continue to

hold the control

 

 

THERMO-

 

 

knob in for about 1/2 minute after the pilot is lit.

 

 

ELECTRIQUE

 

 

 

 

 

 

TO TURN OFF GAS APPLIANCE

 

1) Push in the gas control knob slightly and turn

2) Turn off all electric power to the appliance if

clockwise

 

to “OFF”. Do not force.

service is to be performed.

 

You may shut off the pilot during prolonged non use periods to conserve fuel.

DO NOT REMOVE THIS INSTRUCTION PLATE

908-649a

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

floating. If there is a problem, call a qualified

service person.

4) The appliance and venting system must be

inspected before use, and at least annual-

ly, by a qualified field service person, to

ensure that the flow of combustion and

ventilation air is not obstructed.

During the annual service call, the burners

should be removed from the burner tray

and cleaned. Replace the embers but do

not block the pilot.

5) Keep the area near the appliance clear and

free from combustible materials, gasoline

and other flammable vapours and liquids.

WARNING: CHILDREN AND ADULTSSHOULDBEALERTEDTO THEHAZARDSOFHIGHSURFACE TEMPERATURE AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHINGIGNITION. YOUNGCHIL- DRENSHOULDBECAREFULLYSU- PERVISEDWHENTHEYAREINTHE SAME ROOM AS THE APPLIANCE.

CAUTION: ANY SAFETY SCREEN OR GUARD REMOVED FOR SERV- ICING AN APPLIANCE MUST BE REPLACEDPRIORTOOPERATING THE APPLIANCE.

CLOTHING OR OTHER FLAMMA- BLE MATERIAL SHOULD NOT BE PLACED ON OR NEAR THE APPLI- ANCE.

6)Each time the appliance is lit, it may cause condensation and fog the glass. This con- densation and fog is normal and will disap- pear in a few minutes as the glass heats up.

Never operate the appliance without the glass properly secured in place or with the door open.

7)Do not use this appliance if any part has been under water. Immediately call a qual- ified service technician to inspect the appli- ance and to replace nay part of the control system and any gas control which has been under water.

18

U32-2 FPI Direct Vent Gas Insert

Image 18
Contents U32 Gas Insert FPI GAS Insert To the NEW OwnerTable of Contents Safety Label Installation Minimum Fireplace Dimensions Clearances to Combustibles Materials RequiredManufactured Mobile Home Additional Requirements Flue Liner Installation GAS ConnectionVenting Optional Brick Panel GAS Pipe Pressure TestingGAS Insert Aeration System Natural Gas PropaneLOG SET Installation Faceplate & Trim Installation Rear View Trim Assembly DiagramRear View Faceplate Assembly Diagram Optional Double Door Fire Screen Standard Flush DoorRemoving Bay Door Optional BAY DoorOptional BAY Trim Robert Shaw Extension knobs for Bay Front onlyHampton Cast Faceplate Installation Hampton Logo Left Hand Side Faceplate Diagram Hampton Cast Faceplate Grill InstallationSide Hook Diagram Slots U32 Grill Stop BracketControl Thermostat Wire TableOptional Remote Final CheckWiring Diagram Electrical Grounding InstructionsOperating Instructions Maintenance Instructions Copy of Lighting Instruction PlateMaintenance To remove fan FAN MaintenanceBay Glass Removal Grate screwsShut off the gas supply Valve ReplacementInstall a new gasket and reinstall the valve assembly Heat Gasket ShieldParts List Main AssemblyBurner Assembly & LOG SET Bay Door Flush DoorFaceplate Assembly Hampton Cast Faceplate Assembly Warranty Warranty LifetimeInstaller Please complete the following information