Dacor OBS36, OBSB162, OBS52, OB52 Location Planning Enclosed Cabinets, Optional Finish Trim Kits

Page 12

Planning the Installation

Location Planning - Enclosed Cabinets

Maintain all minimum clearances specified on pages 7 and 8.

For proper outdoor grill operation, provide a flat, level mounting surface with minimum 3/4” thickness.

All models are designed to allow installation in combus- tible or non-combustible base material structures.

On installations without a LP cylinder tank located below the unit, plan the installation so that the gas shut-off valve and pressure regulator are accessible after the appliance is installed so that gas and power can be turned off if service is required. Also, make sure the electric plug can be disconnected easily during ser- vice.

Optional Finish Trim Kits

The optional finish trim can be installed on the countertop to finish the sides and back of the countertop opening. The stainless steel finish trim can be caulked to the countertop and should be secured to the base enclosure with flat head screws. Center the trim within the cutout dimensions noted in this manual, then utilizing the deck screws along with the holes located along the vertical sides of the finish trim, install them securely to the base enclosure countertop sub- straight.

Enclosed Cabinet Installations with a LP Cylinder

When using a LP-gas cylinder, it must be completely enclosed, It must also be ventilated by openings on the sides, back and floor of the enclosure. Each open- ing must have a total area of no less than 10 square inches (254 square mm).

Plan to install the grill in a base structure that has one of the following structural details:

The LP cylinder shut-off valve shall be readily accessible for hand operation. A door on the enclo- sure to gain access to the valve is acceptable, pro- vided it is non-locking and can be opened without the use of tools.

The enclosure for the LP-gas cylinder shall isolate the cylinder from the burner compartment to pro- vide shielding from radiation, a flame barrier and protection from foreign materials such as hot drip- pings.

There shall be a minimum clearance of 2 inches (51mm) between the floor of the LP-gas cylinder enclosure and the ground.

 

10" (254mm) Min. to combustibles

 

1 1/4" (32mm) Min. to non-combustible

 

 

1 1/4"

 

 

28 1/2" (724mm)

(32mm)

 

 

 

 

 

To finished

 

 

 

countertop

 

Junction

 

 

 

 

 

 

Box

 

Rotisserie mounting

1/4"

Trim frame

 

bracket (factory installed)

(6mm)

(accessory)

3/4" (19mm)

23 3/4" (603mm)

 

 

24" (610mm)

 

 

min. to any

 

 

 

 

 

material*

See page 8 for overall cabinet dimensions.

 

OB36, OBS36, OB52 and OBS52

Cutout Dimensions - Side View

10" (254mm) Min. to combustibles

 

2" (51mm) Min. to non-combustible

 

 

Junction

 

 

Box

 

1/4"

Trim frame

 

(6mm)

 

(accessory)

 

 

3/4" (19mm)

23 3/4" (603mm)

 

24" (610mm)

 

Min. to any

See page 8 for overall cabinet dimensions.

material*

OBSB162 Cutout Dimensions -

Side View

The design of the outdoor cooking enclosure must allow the LP-gas cylinder to be connected, disconnect- ed and the connections inspected and tested outside the cylinder enclosure.

Connections which may be disturbed when installing the cylinder in the enclosure can be leak tested inside the enclosure.

Internal mounting means shall be provided on the out- door gas grill for mounting the LP-gas supply cylinder. If the outdoor grill is not in use, the gas must be turned off at the supply cylinder.

7

Image 12
Contents OB36, OB52, OBS36, OBS52, OBSB162 13.2 13.3 Installation Instructions Epicure Outdoor Grill Table of Contents Important Information About Safety Instructions Safety Symbols and LabelsGeneral Safety Precautions Important Safety Instructions Product Dimensions OB36OB52 Overall Number Width HeightGas and Electric Power Requirements Location Planning GeneralElectrical Requirements Enclosed Cabinet Installations with a LP Cylinder OB36, OBS36, OB52 and OBS52 Cutout Dimensions Side ViewOBSB162 Cutout Dimensions Side View Location Planning Enclosed CabinetsCutout Dimensions Top View OBSB162Location Planning Cart Installations Example of Grill Cart LocationPreparing for Installation Parts ListModels OB36, OBS36, OB52 and OBS52 Models OB52, OBS52 and OBSB162Installation Instructions Cabinet Installation Cart InstallationOB36 or OB52 orOptional Side Shelf Installation Connecting the Gas Gas Connection Natural GasGas Connection LP Gas Cylinder Hose Gas Connection Whole House LP GasFinal Assembly and Test Assemble the GrillAssemble the Side Burner Some Models LP Cylinder Installation Some Models Leak TestingPower Connection Cart Models Power Connection Cabinet Installations Installation ChecklistVerifying Proper Operation Lighting InstructionsWiring Diagrams Wiring Diagram OBS52 Page Page Page Ta b l e o f C o n t e n t s Back CoverDacor. all rights reserved Important Safety Instructions Model Number Serial NumberUse an adapter plug Important Safety Instructions Outdoor Grill Features Optional Grill Cart FeaturesGetting to Know Your Outdoor Grill Grill compartment Models OB36 and OBS36Grill compartment Locking wheels Setting Up Your Outdoor Grill Assembling the CooktopOutdoor Grill Assembly Model OBS52 shown Side burner cover Side burner grate Drip tray Warming rackOperating Your Outdoor Grill LP Tank ConnectionTo Connect the LP Tank Selecting and Using Cookware for the Optional Side Burner Tank-less Gas SupplyImportant Operating Information After CookingLighting the Burners Lighting and Preheating Grill CompartmentNever use the outdoor grill in windy conditions Light one burner at a time. Push in onLighting the Side Burners OB52, OBS52 and OBSB162 Only Burner Lighting NotesBurner Knob Locations Model OBS52 Shown Manual Lighting Procedures Grill Compartment To manually light the standard U shaped burnersTo manually light the optional sear burner To manually light one of the optional sear burnersRotisserie Cooking Things to Know About the RotisseriePreparing to Use the Rotisserie Rotisserie OperationManual Lighting Procedure Rotisserie Rotisserie burner Electrode LocationUsing the Smoker Box Smoker CookingSmoker Wood Chip Types Adding more wood chipsUsing the Optional Sear Burner Safe Cooking Temperature ChartTo cook using the sear burner Models OBS36 and OBS52 OnlyCare and Cleaning Cleaning InstructionsCleaning the Grill Compartment Grates Flame spreadersCleaning the Porcelain Grates and Warming Rack Cleaning the Rotisserie Burner and Optional Sear BurnerCleaning the Smoker Box Cleaning the Rotisserie PartsCleaning the Optional Side Burners Cleaning the ExteriorKnobs and Trim Rings Rubbing alcohol to help dissolve grimeLight Bulb Replacement Back of LensLight Fixture Locations Standard U Burner Removal and Replacement Parts and Accessories Before You Call for Service Problem Solution GuideWarranty and Service WarrantyWhat Is Covered What Is Not CoveredBusiness Reply Mail Warranty Information
Related manuals
Manual 12 pages 21.22 Kb