Desa CDCFPRA Continued, INSTALLING OPTIONAL BLOWER ACCESSORY GA3450TA, Assembling Brass Trim

Page 13
Figure 12 - Attaching Brass Trim to

INSTALLATION

Continued

12.Install gas line. See Connecting To Gas Sup- ply, page 16.

13.Check for leaks. See Checking Gas Connec- tions, page 17.

14.Place mantel around fireplace. Be careful not to damage wall or mantel.

15.Place perimeter trim kit on the shoulder screws located on the side and top of the fireplace. Firmly snap trim over shoulder screws on fireplace (see Figure 12).

16.Adjust assembly to remove any gaps. Attach remaining two 3" wood screws from hardware pack through openings inside of fireplace sides into the mantel. The openings are located at top behind the area for top louver (see Figure 12).

17.Reinstall top louver.

Assembling Perimeter Trim (Perimeter trim shipped with mantel)

1.Remove packaging from three remaining pieces of trim.

2.Locate two adjusting plates with set screws, and two shims in the hardware packet.

3.Align shim under adjusting plate as shown in Figure 13.

4.Slide one end of adjusting plate/shim in slot on mitered edge of top brass trim (see Figure 13).

5.Slide other end of adjusting plate/shim in slot on mitered edge of side perimeter trim (see Figure 13).

6.While firmly holding edges of perimeter trim together, tighten both set screws on the adjust- ing plate with slotted screwdriver.

7.Repeat steps 1 through 6 for other corner.

8.Set perimeter trim assembly aside for later installation.

 

Hole for

 

3" Wood

 

Screw for

 

Attaching

Shoulder

Fireplace

Screw

to Mantel

Mantel

 

Base

Gas

 

 

Line

 

Access

 

Hole

 

 

Shoulder

 

 

 

 

Screws

Assembled

Hole for 3" Wood Screw

Brass Trim

for Attaching Fireplace to

 

Wooden Base

Figure 12 - Attaching Brass Trim to

Fireplace

Set Screws

 

 

Adjusting

 

 

Plate

 

Top Brass

 

Slot

 

Trim

 

 

Shim

 

Mitered Edge

 

 

Side Brass

 

 

Trim

 

 

Figure 13 - Assembling Brass Trim

INSTALLING OPTIONAL BLOWER ACCESSORY GA3450TA

Removing Upper Louver To install the blower accessory, you must first remove the upper louver.

1.Lift screen off fireplace and remove log set if installed.

2.Remove 4 screws from upper louver (see Figure 11, page 12). Save these screws.

3.Pull upper louver straight out from the cabinet. Be careful not to scratch the paint. Set louver aside.

4.Open lower louver door by swinging door down (see Figure 11, page 12).

116658-01A

www.desatech.com

13

Image 13
Contents WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance 116658-01A TABLE OF CONTENTSDANGER Carbon monoxide poisoning may lead to death SAFETY INFORMATIONWARNING Any change to this fireplace or its controls can be dangerous See Accessories, page CONTROL ACCESSORIESOPTIONAL REMOTE ContinuedSAFETY PILOT diagrams or failure to use onlyWARNING Always have fireplace. This prevents excesPROVIDING ADEQUATE VENTILATION b. weather stripping has been added on openable windows and doors andFigure 3 - Assembling Hood Unusually Tight ConstructionConfined and Unconfined Space DETERMINING FRESH-AIR FLOW FOR FIREPLACE LOCATIONDetermining if You Have a Confined or Unconfined Space in a recreational vehicle WARNING Never install the fireplace in a bedroom or bathroomas a fireplace insert in high traffic areas in windy or drafty areas VENTILATION AIRBefore installing fireplace, make sure you have the items listed below INSTALLATION ITEMSexternal regulator supplied by installer, for propane/LP units only CHECK GAS TYPElocate fireplace where moving vehicle will not hit it CAUTION If you install the fireplace in a home garageBUILT-IN FIREPLACE INSTALLATION Figure 7 - Rough Opening for Installing in Wall4. If you have not installed hood, follow instruc- tions on page Note A qualified installer should make all electri- cal connections7. Bend four nailing flanges on outer casing with pliers see Figure Figure 9 - Attaching Fireplace to Wall Studsof the following raise the mantel to an accept- able height OPTIONAL MANTEL INSTALLATIONremove the mantel Figure 12 - Attaching Brass Trim to Fireplace INSTALLING OPTIONAL BLOWER ACCESSORY GA3450TAFigure 13 - Assembling Brass Trim Screw Figure 16 - Installing Switch Plate to Remote/Blower Bracket Installing Blower AccessoryCAUTION Verify proper op- eration after servicing Figure 17 - Installing Blower Bracket Assembly For Built-In InstallationFigure 18 - Wiring Diagram For Blower Accessory Built-In Installation CONNECTING TO GAS SUPPLY WARNING Test all gas piping installing or servicing. Correctand connections, internal and external to unit, for leaks afterPRESSURE TESTING FIREPLACE GAS CONNECTIONS PRESSURE TESTING GAS SUPPLY PIPING SYSTEMFigure 24 - Checking Gas Joints Propane/LP Only Figure 25 - Checking Gas Joints Natural Gas OnlyFigure 26 - Disconnecting Wires From Control Valve OPTIONAL WIRELESS HAND-HELD REMOTE CONTROL ACCESSORIESFigure 28 - Installing Remote Receiver OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1Figure 30 - Connecting Wire Terminals 7. Install the base onto the wall with the provided screws“W” and “R” OPTIONAL WALL SWITCH - GWMS2 1. Remove jumper wire from control valve see Figure 26, pageFigure 35 - Installing Log Figure 33 - Installing Rear Brick LinerFigure 36 - Installing Screen Figure 34 - Installing Side Brick LinersOPERATING FIREPLACE FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS 2. If Using Optional Hand-Held Remote MANUAL LIGHTING PROCEDURETO TURN OFF GAS TO APPLIANCE OPTIONAL HAND-HELD REMOTE OPERATIONControl Knob and Flame Adjustment Knob for Remote Operation Figure 40 - Setting the Selector Switch3. Press the POWER and LOCK buttons together to turn off the fireplace 4. Press the POWER and LOCK buttons together to turn off the fireplacesee Troubleshooting, page OPTIONAL GWMS2 WALL MOUNTED SWITCHOPTIONAL GWMT1 WALL MOUNTED THERMOSTAT PILOT FLAME PATTERNCONTINUED WARNING Turn off fireplace and let cool before cleaningBURNER FLAME PATTERN BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLECABINET LOG SETFigure 48 - Pilot Inlet Air Hole Propane/LP Gas Figure 49 - Pilot Inlet Air Hole Natural GasOBSERVED PROBLEM TROUBLESHOOTINGPOSSIBLE CAUSE REMEDYOBSERVED PROBLEM POSSIBLE CAUSE see Cleaning and Mainte Do not try to light any appliance WARNING If you smell gas Shut off gas supplyIf you cannot reach your gas supplier, call the fire department Remote-Ready Models SPECIFICATIONSCDCFPRA CDCFNRASERVICE HINTS REPLACEMENT PARTSTECHNICAL SERVICE PARTS UNDER WARRANTYBREAKDOWN PARTSILLUSTRATED MODELS FIREBOX CDCFNRAFIREBOX MODELS CDCFNRA, CDCFPRA PARTS LISTNatural ILLUSTRATED PARTS BREAKDOWNGas Only REMOTE-READY MODELS THERMOSTAT-CONTROLLED BLOWER KIT GA3450TA NOTICE All accessories may not be available for all fireplace modelsEQUIPMENT SHUTOFF VALVE GA5010 BRASS TRIM KIT - GA6095WALL-MOUNT THERMOSTAT SWITCH GWMT1 CLEANING KIT - GCK/CCKWALL-MOUNT ON/OFF SWITCH GWMS2 RECEIVER AND HAND-HELD REMOTE CONTROL KIT - HRC100 AND HRC1011NOT A UPC 116658-01 Rev. A 04/05 2701 Industrial Drive P.O. Box116658