Desa CDCFNRA, CDCFPRA CAUTION Verify proper op- eration after servicing, Continued

Page 14
Installing Blower Accessory

INSTALLATION

Continued

Installing Blower Accessory

CAUTION: Verify proper op- eration after servicing. CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and danger- ous operation.

Screw Figure 16 - Installing Switch Plate to Remote/Blower Bracket CAUTION: Verify proper op- eration after servicing.

Note: If you are using a mantel with your fireplace, use the following instructions. If your fireplace is built-in, see For Built-In Installation, page 15.

1.Install snap bushings found in blower kit into hole in left side of outer casing and into one of the holes in rear of remote/blower bracket.

2.Make sure the wire harness is firmly connected to the terminals on the blower bracket assembly.

3.Note the wire locations on back of AUTO/ OFF/ON switch. The terminals on back of switch are numbered 1, 2, and 3. Carefully remove red wire from terminal 3 and blue wire from terminal 1. Black wire can remain on middle terminal 2 (see Figure 14).

4.Carefully disconnect green and white wires at their insulated connectors (see Figure 15).

5.In top of the fireplace cabinet, locate the four mounting holes on the outer casing. Align these four holes with those on the blower bracket assembly. Attach blower bracket as- sembly to the outer casing with 4 #10 screws provided (see Figure 14).

6.Route the wire harness through the hole in left side of baffle and between firebox wrapper and outer casing.

7.Insert the 4 wire harnesses from behind the remote/blower bracket through hole in rear of bracket with bushing and through the left rectan- gular hole to front of fireplace (see Figure 14).

8.Reconnect red wire to switch position 3. Reconnect blue wire to switch position 1. Reconnect green and white wires.

9.Install the switch plate on the remote/blower bracket with 2 #10 screws provided (see Figure 16). Route power cord out of the cabinet by inserting it through the bushing on the outer casing (see Figure 14). Plug fan kit into 120- Volt grounded power supply and test operation. Note: When switch is in the AUTO position, the fan will start after the fireplace has run for a few moments. The fan will continue to run for several moments after the fireplace has been turned off. When switch is in the ON position, the fan will run until turned to OFF.

10.Reinstall upper louver beginning with bottom screws (see Figure 11, page 12). Close lower louver door.

Blower

Wiring Routing

Wire Hole in Baffle

 

Bracket

Blower

Assembly

Harness

Mounting

Screw

 

Holes

 

 

Switch

Power

 

 

Cord

3

 

2

 

1

 

Switch

Plate

Wire

Remote/

 

Blower

 

Harness

 

Bracket

 

 

Lower Louver

 

 

 

 

Door

Figure 14 - Installing Blower Bracket Assembly (Remote-Ready Unit Shown)

Fan Switch (Auto/Off/On)

1Auto

 

Off

2

 

 

 

3

Blue

Thermostat

 

 

 

 

 

 

 

On

 

Switch

 

 

 

(N.O.)

 

 

 

 

Blue

110/115

 

Red

 

Blower

V.A.C.

Black

 

 

Motor

 

 

 

Red

 

 

 

 

 

White

 

 

White

 

Green

 

 

Green

Figure 15 - Wiring Diagram For Blower Accessory Standard Installation

Remote/

Blower

Bracket

Switch

Plate Manual background

Screw Manual background Figure 16 - Installing Switch Plate to Remote/Blower Bracket

14

www.desatech.com

116658-01A

Page 13 Page 15
Image 14
Page 13 Page 15
Contents WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance TABLE OF CONTENTS 116658-01AWARNING Any change to this fireplace or its controls can be dangerous SAFETY INFORMATIONDANGER Carbon monoxide poisoning may lead to death OPTIONAL REMOTE CONTROL ACCESSORIESSee Accessories, page ContinuedWARNING Always have diagrams or failure to use onlySAFETY PILOT fireplace. This prevents excesFigure 3 - Assembling Hood b. weather stripping has been added on openable windows and doors andPROVIDING ADEQUATE VENTILATION Unusually Tight ConstructionDetermining if You Have a Confined or Unconfined Space DETERMINING FRESH-AIR FLOW FOR FIREPLACE LOCATIONConfined and Unconfined Space as a fireplace insert in high traffic areas in windy or drafty areas WARNING Never install the fireplace in a bedroom or bathroomin a recreational vehicle VENTILATION AIRexternal regulator supplied by installer, for propane/LP units only INSTALLATION ITEMSBefore installing fireplace, make sure you have the items listed below CHECK GAS TYPEBUILT-IN FIREPLACE INSTALLATION CAUTION If you install the fireplace in a home garagelocate fireplace where moving vehicle will not hit it Figure 7 - Rough Opening for Installing in Wall7. Bend four nailing flanges on outer casing with pliers see Figure Note A qualified installer should make all electri- cal connections4. If you have not installed hood, follow instruc- tions on page Figure 9 - Attaching Fireplace to Wall Studsremove the mantel OPTIONAL MANTEL INSTALLATIONof the following raise the mantel to an accept- able height Figure 13 - Assembling Brass Trim INSTALLING OPTIONAL BLOWER ACCESSORY GA3450TAFigure 12 - Attaching Brass Trim to Fireplace CAUTION Verify proper op- eration after servicing Installing Blower AccessoryScrew Figure 16 - Installing Switch Plate to Remote/Blower Bracket Figure 18 - Wiring Diagram For Blower Accessory Built-In Installation For Built-In InstallationFigure 17 - Installing Blower Bracket Assembly CONNECTING TO GAS SUPPLY and connections, internal and installing or servicing. CorrectWARNING Test all gas piping external to unit, for leaks afterFigure 24 - Checking Gas Joints Propane/LP Only PRESSURE TESTING GAS SUPPLY PIPING SYSTEMPRESSURE TESTING FIREPLACE GAS CONNECTIONS Figure 25 - Checking Gas Joints Natural Gas OnlyFigure 28 - Installing Remote Receiver OPTIONAL WIRELESS HAND-HELD REMOTE CONTROL ACCESSORIESFigure 26 - Disconnecting Wires From Control Valve OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1“W” and “R” OPTIONAL WALL SWITCH - GWMS2 7. Install the base onto the wall with the provided screwsFigure 30 - Connecting Wire Terminals 1. Remove jumper wire from control valve see Figure 26, pageFigure 36 - Installing Screen Figure 33 - Installing Rear Brick LinerFigure 35 - Installing Log Figure 34 - Installing Side Brick LinersLIGHTING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTINGOPERATING FIREPLACE TO TURN OFF GAS TO APPLIANCE MANUAL LIGHTING PROCEDURE2. If Using Optional Hand-Held Remote OPTIONAL HAND-HELD REMOTE OPERATION3. Press the POWER and LOCK buttons together to turn off the fireplace Figure 40 - Setting the Selector SwitchControl Knob and Flame Adjustment Knob for Remote Operation 4. Press the POWER and LOCK buttons together to turn off the fireplaceOPTIONAL GWMT1 WALL MOUNTED THERMOSTAT OPTIONAL GWMS2 WALL MOUNTED SWITCHsee Troubleshooting, page PILOT FLAME PATTERNBURNER FLAME PATTERN WARNING Turn off fireplace and let cool before cleaningCONTINUED BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLEFigure 48 - Pilot Inlet Air Hole Propane/LP Gas LOG SETCABINET Figure 49 - Pilot Inlet Air Hole Natural GasPOSSIBLE CAUSE TROUBLESHOOTINGOBSERVED PROBLEM REMEDYOBSERVED PROBLEM POSSIBLE CAUSE see Cleaning and Mainte If you cannot reach your gas supplier, call the fire department WARNING If you smell gas Shut off gas supplyDo not try to light any appliance CDCFPRA SPECIFICATIONSRemote-Ready Models CDCFNRATECHNICAL SERVICE REPLACEMENT PARTSSERVICE HINTS PARTS UNDER WARRANTYILLUSTRATED MODELS PARTSBREAKDOWN FIREBOX CDCFNRAPARTS LIST FIREBOX MODELS CDCFNRA, CDCFPRAGas Only ILLUSTRATED PARTS BREAKDOWNNatural REMOTE-READY MODELS EQUIPMENT SHUTOFF VALVE GA5010 NOTICE All accessories may not be available for all fireplace modelsTHERMOSTAT-CONTROLLED BLOWER KIT GA3450TA BRASS TRIM KIT - GA6095WALL-MOUNT ON/OFF SWITCH GWMS2 CLEANING KIT - GCK/CCKWALL-MOUNT THERMOSTAT SWITCH GWMT1 RECEIVER AND HAND-HELD REMOTE CONTROL KIT - HRC100 AND HRC1011116658 2701 Industrial Drive P.O. BoxNOT A UPC 116658-01 Rev. A 04/05
Top Page Image Contents