Desa CDCFPRA WARNING Always have, ﬁreplace. This prevents exces, sive temperatures on ﬁreplace

Page 5

SAFETY PILOT

LOCAL CODES

Install and use ﬁreplace with care. Follow all local codes. In the absence of local codes, use the lat- est edition of The National Fuel Gas Code ANSI Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc. 1430 Broadway New York, NY 10018

National Fire Protection Association, Inc. Batterymarch Park Quincy, MA 02269

PRODUCT FEATURES

SAFETY PILOT

This ﬁreplace has a pilot with an Oxygen Deple- tion Sensing (ODS) safety shutoff system. The ODS/pilot is a required feature for vent-free room ﬁreplaces. The ODS/pilot shuts off the ﬁreplace if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This ﬁreplace has a piezo ignitor. This system requires no matches, batteries, or other sources to light ﬁreplace.

UNPACKING

WARNING: Ceramic brick liners are located behind upper louver and must be removed before lighting ﬁreplace.

1.Remove fireplace and hood from carton. Log is wrapped and inside ﬁreplace. Do not remove at this time.

2.Remove all protective packaging applied to ﬁreplace for shipment.

3.Make sure your ﬁreplace includes one hard- ware packet.

4.Check ﬁreplace for any shipping damage. If ﬁreplace is damaged, promptly inform dealer where you bought ﬁreplace.

REMOVING CERAMIC BRICK LINERS

1.Remove screws from top louver and carefully remove louver (see Figure 2).

2.Remove ceramic brick liners with protective packaging. The brick liners will be installed later.

3.Remove yellow sticker from top of ﬁrebox.

4.Replace top louver using screws removed in step 1.

Wrapped

Brick Liners

Top Louver
	Screws


	Figure 2 - Removing Brick Liners
	HOOD ASSEMBLY
	WARNING: Always have
screen in place before operating
ﬁreplace. This prevents exces-
sive temperatures on ﬁreplace
surfaces.
	WARNING: Failure to position
the parts in accordance with these
diagrams or failure to use only
parts speciﬁcally approved with
this ﬁreplace may result in prop-
erty damage or personal injury.
Tools Required:
•	Phillips screwdriver	•	slotted screwdriver
•	5/16" hex wrench	•	scissors
1.	Cut two plastic straps to remove the log from
	the ﬁrebox cavity. Set log aside.
2.	An optional blower is available. See Acces-
	sories, page 38. Install optional blower now.
	Follow installation instructions provided with
	blower and see page 14 or 15, depending on
	your installation.

116658-01A

www.desatech.com

5

Image 5

Contents WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance 116658-01A TABLE OF CONTENTSWARNING Any change to this ﬁreplace or its controls can be dangerous SAFETY INFORMATIONDANGER Carbon monoxide poisoning may lead to death See Accessories, page CONTROL ACCESSORIESOPTIONAL REMOTE ContinuedSAFETY PILOT diagrams or failure to use onlyWARNING Always have ﬁreplace. This prevents excesPROVIDING ADEQUATE VENTILATION b. weather stripping has been added on openable windows and doors andFigure 3 - Assembling Hood Unusually Tight ConstructionDetermining if You Have a Conﬁned or Unconﬁned Space DETERMINING FRESH-AIR FLOW FOR FIREPLACE LOCATIONConﬁned and Unconﬁned Space in a recreational vehicle WARNING Never install the ﬁreplace in a bedroom or bathroomas a ﬁreplace insert in high trafﬁc areas in windy or drafty areas VENTILATION AIRBefore installing ﬁreplace, make sure you have the items listed below INSTALLATION ITEMSexternal regulator supplied by installer, for propane/LP units only CHECK GAS TYPElocate ﬁreplace where moving vehicle will not hit it CAUTION If you install the ﬁreplace in a home garageBUILT-IN FIREPLACE INSTALLATION Figure 7 - Rough Opening for Installing in Wall4. If you have not installed hood, follow instruc- tions on page Note A qualiﬁed installer should make all electri- cal connections7. Bend four nailing ﬂanges on outer casing with pliers see Figure Figure 9 - Attaching Fireplace to Wall Studsremove the mantel OPTIONAL MANTEL INSTALLATIONof the following raise the mantel to an accept- able height Figure 13 - Assembling Brass Trim INSTALLING OPTIONAL BLOWER ACCESSORY GA3450TAFigure 12 - Attaching Brass Trim to Fireplace CAUTION Verify proper op- eration after servicing Installing Blower AccessoryScrew Figure 16 - Installing Switch Plate to Remote/Blower Bracket Figure 18 - Wiring Diagram For Blower Accessory Built-In Installation For Built-In InstallationFigure 17 - Installing Blower Bracket Assembly CONNECTING TO GAS SUPPLY WARNING Test all gas piping installing or servicing. Correctand connections, internal and external to unit, for leaks afterPRESSURE TESTING FIREPLACE GAS CONNECTIONS PRESSURE TESTING GAS SUPPLY PIPING SYSTEMFigure 24 - Checking Gas Joints Propane/LP Only Figure 25 - Checking Gas Joints Natural Gas OnlyFigure 26 - Disconnecting Wires From Control Valve OPTIONAL WIRELESS HAND-HELD REMOTE CONTROL ACCESSORIESFigure 28 - Installing Remote Receiver OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1Figure 30 - Connecting Wire Terminals 7. Install the base onto the wall with the provided screws“W” and “R” OPTIONAL WALL SWITCH - GWMS2 1. Remove jumper wire from control valve see Figure 26, pageFigure 35 - Installing Log Figure 33 - Installing Rear Brick LinerFigure 36 - Installing Screen Figure 34 - Installing Side Brick LinersLIGHTING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTINGOPERATING FIREPLACE 2. If Using Optional Hand-Held Remote MANUAL LIGHTING PROCEDURETO TURN OFF GAS TO APPLIANCE OPTIONAL HAND-HELD REMOTE OPERATIONControl Knob and Flame Adjustment Knob for Remote Operation Figure 40 - Setting the Selector Switch3. Press the POWER and LOCK buttons together to turn off the ﬁreplace 4. Press the POWER and LOCK buttons together to turn off the ﬁreplacesee Troubleshooting, page OPTIONAL GWMS2 WALL MOUNTED SWITCHOPTIONAL GWMT1 WALL MOUNTED THERMOSTAT PILOT FLAME PATTERNCONTINUED WARNING Turn off ﬁreplace and let cool before cleaningBURNER FLAME PATTERN BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLECABINET LOG SETFigure 48 - Pilot Inlet Air Hole Propane/LP Gas Figure 49 - Pilot Inlet Air Hole Natural GasOBSERVED PROBLEM TROUBLESHOOTINGPOSSIBLE CAUSE REMEDYOBSERVED PROBLEM POSSIBLE CAUSE see Cleaning and Mainte If you cannot reach your gas supplier, call the ﬁre department WARNING If you smell gas Shut off gas supplyDo not try to light any appliance Remote-Ready Models SPECIFICATIONSCDCFPRA CDCFNRASERVICE HINTS REPLACEMENT PARTSTECHNICAL SERVICE PARTS UNDER WARRANTYBREAKDOWN PARTSILLUSTRATED MODELS FIREBOX CDCFNRAFIREBOX MODELS CDCFNRA, CDCFPRA PARTS LISTGas Only ILLUSTRATED PARTS BREAKDOWNNatural REMOTE-READY MODELS THERMOSTAT-CONTROLLED BLOWER KIT GA3450TA NOTICE All accessories may not be available for all ﬁreplace modelsEQUIPMENT SHUTOFF VALVE GA5010 BRASS TRIM KIT - GA6095WALL-MOUNT THERMOSTAT SWITCH GWMT1 CLEANING KIT - GCK/CCKWALL-MOUNT ON/OFF SWITCH GWMS2 RECEIVER AND HAND-HELD REMOTE CONTROL KIT - HRC100 AND HRC1011116658 2701 Industrial Drive P.O. BoxNOT A UPC 116658-01 Rev. A 04/05