Desa CDCFPRA, CDCFNRA Continued, Optional Wireless Hand-Held Remote Control Accessories

Page 19

OPTIONAL WIRELESS HAND-HELD REMOTE CONTROL ACCESSORIES

INSTALLATION

Continued

OPTIONAL WIRELESS HAND-HELD REMOTE CONTROL ACCESSORIES

Installing Receiver

1.Disconnect wires from the control valve (see Figure 26).

2.Locate the battery clip mounted on the back of the receiver (see Figure 27).

3.Slide 9-volt battery (not included) through the clip.

4.Attach the terminal wires to the battery (see Figure 27).

5.Connect wires from remote receiver to control valve as shown in Figure 28.

6.Install remote receiver unit onto remote/ blower bracket using screws provided (see Figure 28).

Figure 26 - Disconnecting Wires From

Control Valve

Receiver

9-Volt	Terminal
Battery	Wires
	Battery Clip

Figure 27 - Attaching Battery to Receiver

White Wire to

TH Terminal on

Control Valve

Remote

Receiver

Red Wire to

TPTH Terminal on

Control Valve

Figure 28 - Installing Remote Receiver

Installing 9-Volt Battery in Hand-Held Remote Control Unit

1.Remove battery cover on back of remote control unit.

2.Attach terminal wires to the battery (not includ- ed). Place battery into the battery housing.

3.Replace battery cover onto remote control unit.

Battery	Remote Control Unit
Cover

Terminal

Wires

Battery

Housing

9-Volt Battery

Figure 29 - Installing Battery in Hand- Held Remote Control Unit

OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1

WARNING: Read and fol- low installation instructions. Installation should be done by a qualiﬁed installer familiar with low-voltage wiring procedures.

WARNING: Do not connect this thermostat to any electrical source! Electrical shock and/or ﬁre hazard will occur.

1.Remove jumper wire from control valve (see Figure 26).

2.Connect one terminal of 25 ft. wire to the “TH” terminal on the control valve. Connect the other terminal to the “THTP” terminal on the control valve. See Figure 30, page 20.

3.Route the 25 ft. wire to a convenient location to mount your thermostat (no outside wall). IMPORTANT: The wire may be shortened but must not be lengthened.

The thermostat should be mounted 54" above the ﬂoor in a location where there is good air circulation. Avoid heat sources such as lamps, direct sunlight, ﬁreplace, or heat and air conditioning ducts.

116658-01A

www.desatech.com

19

Image 19

Contents WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance 116658-01A TABLE OF CONTENTSDANGER Carbon monoxide poisoning may lead to death SAFETY INFORMATIONWARNING Any change to this ﬁreplace or its controls can be dangerous Continued CONTROL ACCESSORIESSee Accessories, page OPTIONAL REMOTEﬁreplace. This prevents exces diagrams or failure to use onlySAFETY PILOT WARNING Always haveUnusually Tight Construction b. weather stripping has been added on openable windows and doors andPROVIDING ADEQUATE VENTILATION Figure 3 - Assembling HoodConﬁned and Unconﬁned Space DETERMINING FRESH-AIR FLOW FOR FIREPLACE LOCATIONDetermining if You Have a Conﬁned or Unconﬁned Space VENTILATION AIR WARNING Never install the ﬁreplace in a bedroom or bathroomin a recreational vehicle as a ﬁreplace insert in high trafﬁc areas in windy or drafty areasCHECK GAS TYPE INSTALLATION ITEMSBefore installing ﬁreplace, make sure you have the items listed below external regulator supplied by installer, for propane/LP units onlyFigure 7 - Rough Opening for Installing in Wall CAUTION If you install the ﬁreplace in a home garagelocate ﬁreplace where moving vehicle will not hit it BUILT-IN FIREPLACE INSTALLATIONFigure 9 - Attaching Fireplace to Wall Studs Note A qualiﬁed installer should make all electri- cal connections4. If you have not installed hood, follow instruc- tions on page 7. Bend four nailing ﬂanges on outer casing with pliers see Figureof the following raise the mantel to an accept- able height OPTIONAL MANTEL INSTALLATIONremove the mantel Figure 12 - Attaching Brass Trim to Fireplace INSTALLING OPTIONAL BLOWER ACCESSORY GA3450TAFigure 13 - Assembling Brass Trim Screw Figure 16 - Installing Switch Plate to Remote/Blower Bracket Installing Blower AccessoryCAUTION Verify proper op- eration after servicing Figure 17 - Installing Blower Bracket Assembly For Built-In InstallationFigure 18 - Wiring Diagram For Blower Accessory Built-In Installation CONNECTING TO GAS SUPPLY external to unit, for leaks after installing or servicing. CorrectWARNING Test all gas piping and connections, internal andFigure 25 - Checking Gas Joints Natural Gas Only PRESSURE TESTING GAS SUPPLY PIPING SYSTEMPRESSURE TESTING FIREPLACE GAS CONNECTIONS Figure 24 - Checking Gas Joints Propane/LP OnlyOPTIONAL WALL MOUNTED THERMOSTAT - GWMT1 OPTIONAL WIRELESS HAND-HELD REMOTE CONTROL ACCESSORIESFigure 26 - Disconnecting Wires From Control Valve Figure 28 - Installing Remote Receiver1. Remove jumper wire from control valve see Figure 26, page 7. Install the base onto the wall with the provided screwsFigure 30 - Connecting Wire Terminals “W” and “R” OPTIONAL WALL SWITCH - GWMS2Figure 34 - Installing Side Brick Liners Figure 33 - Installing Rear Brick LinerFigure 35 - Installing Log Figure 36 - Installing ScreenOPERATING FIREPLACE FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS OPTIONAL HAND-HELD REMOTE OPERATION MANUAL LIGHTING PROCEDURE2. If Using Optional Hand-Held Remote TO TURN OFF GAS TO APPLIANCE4. Press the POWER and LOCK buttons together to turn off the ﬁreplace Figure 40 - Setting the Selector SwitchControl Knob and Flame Adjustment Knob for Remote Operation 3. Press the POWER and LOCK buttons together to turn off the ﬁreplacePILOT FLAME PATTERN OPTIONAL GWMS2 WALL MOUNTED SWITCHsee Troubleshooting, page OPTIONAL GWMT1 WALL MOUNTED THERMOSTATBURNER INJECTOR HOLDER AND PILOT AIR INLET HOLE WARNING Turn off ﬁreplace and let cool before cleaningCONTINUED BURNER FLAME PATTERNFigure 49 - Pilot Inlet Air Hole Natural Gas LOG SETCABINET Figure 48 - Pilot Inlet Air Hole Propane/LP GasREMEDY TROUBLESHOOTINGOBSERVED PROBLEM POSSIBLE CAUSEOBSERVED PROBLEM POSSIBLE CAUSE see Cleaning and Mainte Do not try to light any appliance WARNING If you smell gas Shut off gas supplyIf you cannot reach your gas supplier, call the ﬁre department CDCFNRA SPECIFICATIONSRemote-Ready Models CDCFPRAPARTS UNDER WARRANTY REPLACEMENT PARTSSERVICE HINTS TECHNICAL SERVICEFIREBOX CDCFNRA PARTSBREAKDOWN ILLUSTRATED MODELSFIREBOX MODELS CDCFNRA, CDCFPRA PARTS LISTNatural ILLUSTRATED PARTS BREAKDOWNGas Only REMOTE-READY MODELS BRASS TRIM KIT - GA6095 NOTICE All accessories may not be available for all ﬁreplace modelsTHERMOSTAT-CONTROLLED BLOWER KIT GA3450TA EQUIPMENT SHUTOFF VALVE GA5010RECEIVER AND HAND-HELD REMOTE CONTROL KIT - HRC100 AND HRC1011 CLEANING KIT - GCK/CCKWALL-MOUNT THERMOSTAT SWITCH GWMT1 WALL-MOUNT ON/OFF SWITCH GWMS2NOT A UPC 116658-01 Rev. A 04/05 2701 Industrial Drive P.O. Box116658