Desa CDCFPRA To Turn Off Gas To Appliance, Manual Lighting Procedure, Shutting Off Fireplace

Page 23
TO TURN OFF GAS

OPERATING FIREPLACE

Continued

6.With control knob pressed in, press and release ignitor button. This will light pilot. The pilot is attached to the front burner. If needed, keep pressing ignitor button until pilot lights.

Note: If pilot does not stay lit, contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure.

7.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

•If control knob does not pop out when released, contact a qualified service person or gas supplier for repairs.

Note: If pilot goes out, repeat steps 4 through 8.

8.Slightly push in and turn control knob coun-

terclockwise Shutting Off Fireplace to the ON position.

9.Set flame adjustment knob to any level between HI and LO.

2.If Using Optional Hand-Held Remote: CAUTION: Do not try to ad- just heating levels by using the equipment shutoff valve.

Pilot

Ignitor

Burner

Electrode

 

Figure 38 - Propane/LP Gas Pilot

Pilot Burner

Ignitor

Electrode

 

Figure 39 - Natural Gas Pilot

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Fireplace

1.Turn control knob clockwise MANUAL LIGHTING to the OFF position.

2.If Using Optional Hand-Held Remote:

Set selector switch in the OFF position to prevent draining battery.

Shutting Off Burners Only (pilot stays lit) You may shut off the burners and keep the pilot lit by doing one of the following:

1.Turn control knob clockwise OPTIONAL HAND-HELD to the PILOT position.

2.If Using Optional Hand-Held Remote: Use remote control manual OFF button.

Manual background WARNING:Makesureremote sensor selector switch is in the OFF position when you are away from home for long periods of time.

MANUAL LIGHTING

PROCEDURE

1.Follow steps 1 through 5 under Lighting Instructions, page 22.

2.Depress control knob and light pilot with match.

3.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow steps 8 and 9 under Lighting Instructions, column 1.

OPTIONAL HAND-HELD

REMOTE OPERATION

Note: All remote control accessories must be purchased separately (see Accessories, page 44). Follow instructions included with the remote control.

NOTICE: You must light the pilot before using the hand-held re- mote control unit. See Lighting Instructions on page 22.

After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Ad- just flame adjustment knob anywhere between HI and LO. Slide the selector switch to the RE- MOTE position (see Figure 40, page 24).

116658-01A

www.desatech.com

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance 116658-01A TABLE OF CONTENTSWARNING Any change to this fireplace or its controls can be dangerous SAFETY INFORMATIONDANGER Carbon monoxide poisoning may lead to death Continued CONTROL ACCESSORIESSee Accessories, page OPTIONAL REMOTEfireplace. This prevents exces diagrams or failure to use onlySAFETY PILOT WARNING Always haveUnusually Tight Construction b. weather stripping has been added on openable windows and doors andPROVIDING ADEQUATE VENTILATION Figure 3 - Assembling HoodDetermining if You Have a Confined or Unconfined Space DETERMINING FRESH-AIR FLOW FOR FIREPLACE LOCATIONConfined and Unconfined Space VENTILATION AIR WARNING Never install the fireplace in a bedroom or bathroomin a recreational vehicle as a fireplace insert in high traffic areas in windy or drafty areasCHECK GAS TYPE INSTALLATION ITEMSBefore installing fireplace, make sure you have the items listed below external regulator supplied by installer, for propane/LP units onlyFigure 7 - Rough Opening for Installing in Wall CAUTION If you install the fireplace in a home garagelocate fireplace where moving vehicle will not hit it BUILT-IN FIREPLACE INSTALLATIONFigure 9 - Attaching Fireplace to Wall Studs Note A qualified installer should make all electri- cal connections4. If you have not installed hood, follow instruc- tions on page 7. Bend four nailing flanges on outer casing with pliers see Figureremove the mantel OPTIONAL MANTEL INSTALLATIONof the following raise the mantel to an accept- able height Figure 13 - Assembling Brass Trim INSTALLING OPTIONAL BLOWER ACCESSORY GA3450TAFigure 12 - Attaching Brass Trim to Fireplace CAUTION Verify proper op- eration after servicing Installing Blower AccessoryScrew Figure 16 - Installing Switch Plate to Remote/Blower Bracket Figure 18 - Wiring Diagram For Blower Accessory Built-In Installation For Built-In InstallationFigure 17 - Installing Blower Bracket Assembly CONNECTING TO GAS SUPPLY external to unit, for leaks after installing or servicing. CorrectWARNING Test all gas piping and connections, internal andFigure 25 - Checking Gas Joints Natural Gas Only PRESSURE TESTING GAS SUPPLY PIPING SYSTEMPRESSURE TESTING FIREPLACE GAS CONNECTIONS Figure 24 - Checking Gas Joints Propane/LP OnlyOPTIONAL WALL MOUNTED THERMOSTAT - GWMT1 OPTIONAL WIRELESS HAND-HELD REMOTE CONTROL ACCESSORIESFigure 26 - Disconnecting Wires From Control Valve Figure 28 - Installing Remote Receiver1. Remove jumper wire from control valve see Figure 26, page 7. Install the base onto the wall with the provided screwsFigure 30 - Connecting Wire Terminals “W” and “R” OPTIONAL WALL SWITCH - GWMS2Figure 34 - Installing Side Brick Liners Figure 33 - Installing Rear Brick LinerFigure 35 - Installing Log Figure 36 - Installing ScreenLIGHTING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTINGOPERATING FIREPLACE OPTIONAL HAND-HELD REMOTE OPERATION MANUAL LIGHTING PROCEDURE2. If Using Optional Hand-Held Remote TO TURN OFF GAS TO APPLIANCE4. Press the POWER and LOCK buttons together to turn off the fireplace Figure 40 - Setting the Selector SwitchControl Knob and Flame Adjustment Knob for Remote Operation 3. Press the POWER and LOCK buttons together to turn off the fireplacePILOT FLAME PATTERN OPTIONAL GWMS2 WALL MOUNTED SWITCHsee Troubleshooting, page OPTIONAL GWMT1 WALL MOUNTED THERMOSTATBURNER INJECTOR HOLDER AND PILOT AIR INLET HOLE WARNING Turn off fireplace and let cool before cleaningCONTINUED BURNER FLAME PATTERNFigure 49 - Pilot Inlet Air Hole Natural Gas LOG SETCABINET Figure 48 - Pilot Inlet Air Hole Propane/LP GasREMEDY TROUBLESHOOTINGOBSERVED PROBLEM POSSIBLE CAUSEOBSERVED PROBLEM POSSIBLE CAUSE see Cleaning and Mainte If you cannot reach your gas supplier, call the fire department WARNING If you smell gas Shut off gas supplyDo not try to light any appliance CDCFNRA SPECIFICATIONSRemote-Ready Models CDCFPRAPARTS UNDER WARRANTY REPLACEMENT PARTSSERVICE HINTS TECHNICAL SERVICEFIREBOX CDCFNRA PARTSBREAKDOWN ILLUSTRATED MODELSFIREBOX MODELS CDCFNRA, CDCFPRA PARTS LISTGas Only ILLUSTRATED PARTS BREAKDOWNNatural REMOTE-READY MODELS BRASS TRIM KIT - GA6095 NOTICE All accessories may not be available for all fireplace modelsTHERMOSTAT-CONTROLLED BLOWER KIT GA3450TA EQUIPMENT SHUTOFF VALVE GA5010RECEIVER AND HAND-HELD REMOTE CONTROL KIT - HRC100 AND HRC1011 CLEANING KIT - GCK/CCKWALL-MOUNT THERMOSTAT SWITCH GWMT1 WALL-MOUNT ON/OFF SWITCH GWMS2116658 2701 Industrial Drive P.O. BoxNOT A UPC 116658-01 Rev. A 04/05
Top Page Image Contents