Desa CDCFPRA, CDCFNRA Continued, Installing Rear Brick Liner, Installing Log, Installing Screen

Page 21

Figure 33 - Installing Rear Brick Liner

INSTALLATION

Continued

3.Install left and right brick liners using brackets and screws from hardware kit as shown in Fig- ure 34. Screw the bracket into top of ﬁrebox and against brick liners. Adjust bracket before tightening screw.

4.Remove log packaging material and discard. Gently place log over burner (see Figure 35). (Do not allow log to contact ﬂame as this will create sooting.)

5.Insert each rod through ten rings located at top of screen (see Figure 36).

6.Insert ﬁrst rod into hole in left side of ﬁrebox. Fasten rod to rear hole near center of ﬁrebox us- ing black Phillips head screw (see Figure 36).

7.Insert other rod into hole on right side of ﬁre- box and fasten rod to front hole near center of ﬁrebox using remaining sheet metal screw.

Rear Brick

Liner

Figure 33 - Installing Rear Brick Liner

Log Set

Figure 35 - Installing Log

	Back Center
	Hole for Left
Front Center	Screen Assembly
Hole for
Right Screen
Assembly

Screen

Rod

Rings

Screen

Screen

Assembly

Figure 36 - Installing Screen

Brick Liner

Bracket and

Screw

Left Brick

Liner

Figure 34 - Installing Side Brick Liners

116658-01A

www.desatech.com

21

Image 21

Contents WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance 116658-01A TABLE OF CONTENTSSAFETY INFORMATION DANGER Carbon monoxide poisoning may lead to deathWARNING Any change to this ﬁreplace or its controls can be dangerous See Accessories, page CONTROL ACCESSORIESOPTIONAL REMOTE ContinuedSAFETY PILOT diagrams or failure to use onlyWARNING Always have ﬁreplace. This prevents excesPROVIDING ADEQUATE VENTILATION b. weather stripping has been added on openable windows and doors andFigure 3 - Assembling Hood Unusually Tight ConstructionDETERMINING FRESH-AIR FLOW FOR FIREPLACE LOCATION Conﬁned and Unconﬁned SpaceDetermining if You Have a Conﬁned or Unconﬁned Space in a recreational vehicle WARNING Never install the ﬁreplace in a bedroom or bathroomas a ﬁreplace insert in high trafﬁc areas in windy or drafty areas VENTILATION AIRBefore installing ﬁreplace, make sure you have the items listed below INSTALLATION ITEMSexternal regulator supplied by installer, for propane/LP units only CHECK GAS TYPElocate ﬁreplace where moving vehicle will not hit it CAUTION If you install the ﬁreplace in a home garageBUILT-IN FIREPLACE INSTALLATION Figure 7 - Rough Opening for Installing in Wall4. If you have not installed hood, follow instruc- tions on page Note A qualiﬁed installer should make all electri- cal connections7. Bend four nailing ﬂanges on outer casing with pliers see Figure Figure 9 - Attaching Fireplace to Wall StudsOPTIONAL MANTEL INSTALLATION of the following raise the mantel to an accept- able heightremove the mantel INSTALLING OPTIONAL BLOWER ACCESSORY GA3450TA Figure 12 - Attaching Brass Trim to FireplaceFigure 13 - Assembling Brass Trim Installing Blower Accessory Screw Figure 16 - Installing Switch Plate to Remote/Blower BracketCAUTION Verify proper op- eration after servicing For Built-In Installation Figure 17 - Installing Blower Bracket AssemblyFigure 18 - Wiring Diagram For Blower Accessory Built-In Installation CONNECTING TO GAS SUPPLY WARNING Test all gas piping installing or servicing. Correctand connections, internal and external to unit, for leaks afterPRESSURE TESTING FIREPLACE GAS CONNECTIONS PRESSURE TESTING GAS SUPPLY PIPING SYSTEMFigure 24 - Checking Gas Joints Propane/LP Only Figure 25 - Checking Gas Joints Natural Gas OnlyFigure 26 - Disconnecting Wires From Control Valve OPTIONAL WIRELESS HAND-HELD REMOTE CONTROL ACCESSORIESFigure 28 - Installing Remote Receiver OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1Figure 30 - Connecting Wire Terminals 7. Install the base onto the wall with the provided screws“W” and “R” OPTIONAL WALL SWITCH - GWMS2 1. Remove jumper wire from control valve see Figure 26, pageFigure 35 - Installing Log Figure 33 - Installing Rear Brick LinerFigure 36 - Installing Screen Figure 34 - Installing Side Brick LinersFOR YOUR SAFETY READ BEFORE LIGHTING OPERATING FIREPLACELIGHTING INSTRUCTIONS 2. If Using Optional Hand-Held Remote MANUAL LIGHTING PROCEDURETO TURN OFF GAS TO APPLIANCE OPTIONAL HAND-HELD REMOTE OPERATIONControl Knob and Flame Adjustment Knob for Remote Operation Figure 40 - Setting the Selector Switch3. Press the POWER and LOCK buttons together to turn off the ﬁreplace 4. Press the POWER and LOCK buttons together to turn off the ﬁreplacesee Troubleshooting, page OPTIONAL GWMS2 WALL MOUNTED SWITCHOPTIONAL GWMT1 WALL MOUNTED THERMOSTAT PILOT FLAME PATTERNCONTINUED WARNING Turn off ﬁreplace and let cool before cleaningBURNER FLAME PATTERN BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLECABINET LOG SETFigure 48 - Pilot Inlet Air Hole Propane/LP Gas Figure 49 - Pilot Inlet Air Hole Natural GasOBSERVED PROBLEM TROUBLESHOOTINGPOSSIBLE CAUSE REMEDYOBSERVED PROBLEM POSSIBLE CAUSE see Cleaning and Mainte WARNING If you smell gas Shut off gas supply Do not try to light any applianceIf you cannot reach your gas supplier, call the ﬁre department Remote-Ready Models SPECIFICATIONSCDCFPRA CDCFNRASERVICE HINTS REPLACEMENT PARTSTECHNICAL SERVICE PARTS UNDER WARRANTYBREAKDOWN PARTSILLUSTRATED MODELS FIREBOX CDCFNRAFIREBOX MODELS CDCFNRA, CDCFPRA PARTS LISTILLUSTRATED PARTS BREAKDOWN NaturalGas Only REMOTE-READY MODELS THERMOSTAT-CONTROLLED BLOWER KIT GA3450TA NOTICE All accessories may not be available for all ﬁreplace modelsEQUIPMENT SHUTOFF VALVE GA5010 BRASS TRIM KIT - GA6095WALL-MOUNT THERMOSTAT SWITCH GWMT1 CLEANING KIT - GCK/CCKWALL-MOUNT ON/OFF SWITCH GWMS2 RECEIVER AND HAND-HELD REMOTE CONTROL KIT - HRC100 AND HRC10112701 Industrial Drive P.O. Box NOT A UPC 116658-01 Rev. A 04/05116658