Desa VTGF33NRA Relocating Wall Switch Assembly, Electrical Connections for Power Cord

Page 9

INSTALLATION

Removing Fireplace Screen And Floor Assembly (Cont.) Electrical Connections for Power Cord Relocating Wall Switch Assembly

9

INSTALLATION

Continued

Hole in Floor

Hole in Outer

Support Bracket

Casing

Screw

Fireplace Floor Assembly

Screw

Flexible Gas Line

Bushings

Power Cord

Figure 7 - Routing Power Cord

RELOCATING WALL SWITCH ASSEMBLY

Figure 6 - Removing Fireplace Floor Assembly

ELECTRICAL CONNECTIONS FOR POWER CORD

This fireplace operates on 120 VAC, 60 Hz power. An electrical power cord is supplied with this unit.

For Mantel Installation

1.Determine from which side of the fireplace the power cord will exit. Locate the 1.5" diameter hole near the center of floor sup- port bracket on appropriate side of lower cavity (see Figure 7).

2.Locate power cord. Remove wire tie or tape holding plug end of power cord.

3.Power cord has 2 plastic hole bushings threaded onto it. Route cord's 3-prong plug through the 1.5" diameter hole in appro- priate floor support bracket.

4.Push first plastic bushing completely through hole. Squeeze bushing as needed to do this.

5.Install the second plastic bushing into the hole in the floor sup- port bracket by snapping into place.

6.Route the 3-prong plug through the 1.5" hole in fireplace outer casing.

7.Install the first plastic bushing into this hole by snapping into place.

8.After you have connected to gas supply and checked your gas connections (see pages 15 and 16), plug power cord into any convenient 3-prong grounded wall receptacle near fireplace.

For Recessed Installation

If an outlet is not installed in fireplace, install model GA3555 - Outlet Kit with Cover. This kit will supply a convenient 3-prong grounded electrical outlet for power. Refer to installation manual provided with this optional accessory for instructions on wiring. Note: A qualified installer must make all electrical connections.

Note: The decorative wall switch plate supplied is white. The wall switch plate may be painted to match your decor.

The push-button switch and decorative wall plate assembly sup- plied with your fireplace is pre-mounted at the factory in the lower cavity of the fireplace. You may relocate this wall switch assembly to a more convenient location such as the side of your mantel or directly onto the wall near the fireplace. To mount the wall switch assembly, you must first cut openings in the mantel or wall where the switch will be located.

Note: If you choose to relocate the wall switch assembly, do so before final installation into a mantel or recessing into a wall. If you are installing an optional blower accessory, install it at the same time you relocate the wall switch assembly.

CAUTION: The wall switch assembly must never be mounted directly above the fireplace where heat may damage it. If you relocate wall switch assembly from lower fireplace cavity, it must be mounted either on side wall of mantel or on wall to side of fireplace.

For Recessed Installation

If fireplace is to be recessed into a wall (see Built-In Fireplace Installation, page 15), we recommend mounting wall switch assembly to left side of fireplace. The wall switch assembly should be mounted approximately 12" from left edge of fireplace, and less than 60" from the floor. IMPORTANT: Do not locate wall switch assembly directly in front of wall stud - there must be room behind wall board for wires from switch. If you choose to locate wall switch assembly to right side of fireplace, the length of the cord restricts you to less than 6" from right edge of fireplace and less than 48" from floor.

For morevisit www..com

110112-01A

Page 8 Page 10
Image 9
Page 8 Page 10
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualSafety Information Table of ContentsOther gases Product IdentificationProduct Features Local CodesUnpacking Providing Adequate Ventilation AIR for Combustion and VentilationUnusually Tight Construction Confined Space and Unconfined SpaceVentilation AIR Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside BuildingInstallation Check GAS TypeVentilation Air From Outdoors Installation Sequence Installation ClearancesRemoving Fireplace Screen and Floor Assembly Electrical HookupElectrical Connections for Power Cord Relocating Wall Switch AssemblyRelocating Wall Switch Assembly Mounting Wall Switch Assembly to Side of Mantel Installing GAS Piping to Fireplace LocationInstallation Items Needed Connecting Fireplace to GAS SupplyPressure Testing Fireplace Gas Connections Pressure Testing Gas Supply Piping SystemChecking GAS Connections Hole Conventional Fireplace InstallationMantel Clearances for Built-In Installation BUILT-IN Fireplace InstallationInstalling Hood Installing LogsAssembling and Attaching Optional Brass Trim Installing Log #2 Right and Log #3 Left Installing Battery Into RemoteFor Your Safety Read Before Lighting Installing ScreenUsing Supplied Wall Switch Assembly Operating FireplaceFor Electrical Power Outage To Turn OFF GAS To ApplianceManual Lighting Instructions Inspecting Burners Shutting Off Heater When Manually LitOptional Blower Operation Operating FANCleaning Maintenance Cleaning Burner Injector Holders and Pilot AIR Inlet HolesBurner Flame Patterns Logs SpecificationsObserved Problem Possible Cause Remedy TroubleshootingFor Com Gas leak. See Warning statement Illustrated Parts Breakdown Remote Control LOG Base Assembly Models VTGF33PRA VTGF33NRA Parts ListFireplace Models VTGF33NRA VTGF33PRA Fireplace Models VTGF33NRA and VTGF33PRA Accessories Slim Hearth Base Cleaning KIT GCKLaminate Trim for Hearth or Mantel Firebox Brick Liner G8000 SeriesService Hints Replacement PartsTechnical Service Wiring DiagramDiameter Holes TemplatesThis page Intentionally Left Blank Owners Registration Form Postage Required 110112-01A Not a UPC
Top Page Image Contents