Panasonic CS-KE30NKU Adjusting the Airflow Direction, When the air conditioner is not running

Page 75

ADJUSTING THE AIRFLOW DIRECTION

1. Horizontal

The horizontal airflow can be adjusted by moving the vertical vanes with your hands to the left or right.

CAUTION

When the humidity is high, the vertical vanes should be in the front position during the cooling or dehumidifying operation. If the vertical vanes are positioned all of the way to the right or left, condensation may begin to form around the air vent and drip down.

2. Vertical

The vertical airflow can be adjusted by moving the flap with the remote controller. Do not move the flap with your hands. Confirm that the remote controller has been turned on. Use the FLAP button to set either the sweep function or one of the six airflow direction settings.

A. Sweep function

The flap starts moving up and down to deliver air over the sweep range.

B. Setting the airflow manually

 

SWEEP

Referring to the above COOL

 

illustration, use the

DRY

SWEEP

FLAP button to set the

FAN

 

airflow direction within

 

HEAT

the range used during

 

 

 

the heating, cooling, or

 

 

dehumidifying

 

 

operation.

 

 

C. Auto flap function

The flap is set to the recommended position.

NOTE

The flap automatically closes when the unit is off.

During the heating operation, the fan speed will be very low and the flap will be in the horizontal position (position ) until the air being blown out of the unit begins to warm. Once the air warms up, the flap position and fan speed change to the settings specified with the remote controller.

CAUTION

Use the FLAP button on the remote controller to adjust the position of the flap. If you move the flap by hand, the flap position according to the remote controller and the actual flap position may no longer match. If this should happen, shut off the unit, wait for the flap to close, and then turn on the unit again; the flap position will now be normal again.

Do not have the flap pointed down during cooling operation. Condensation may begin to form around the air vent and drip down.

OPERATION WITHOUT THE REMOTE CONTROLLER

INDOOR UNIT

OPERATION lamp

OPERATION button (ON/OFF)

If you have lost the remote controller or it has trouble, follow the steps below.

When the air conditioner is not running

Each time the OPERATION button is pressed, the type of operation conducted is indicated by the changing color of the OPERATION lamp. Press the button and select the lamp color that suits your preference for operation.

Cooling operation

 

Heating

 

Stop

 

 

(green)

 

operation (red)

(lamp off)

NOTE

The temperature is set to the room temperature minus 4°F during the cooling operation and to the room temperature plus 4°F during the heating operation, and the fan speed and flap are set to Auto.

15

Image 75
Contents 852 360 CS-KE30NKU + CU-KE30NKU CS-KE36NKU + CU-KE36NKUIndoor Model No Product Code No Outdoor Model No Product Code NoSafety Precautions Prohibit Table of Contents Checking Electrical Components Operating Range Temperature Indoor Air Intake Temp Outdoor Air Intake TempOutdoor Unit SpecificationsUnit Specifications Indoor Unit208V CS-KE36NKU 21.9 19.9 Major Component Specifications Indoor UnitIndoor Unit CS-KE30NKU CB-CS-KE36NKU Indoor Unit CS-KE36NKUCompressor Outdoor UnitOutdoor Unit CU-KE30NKU BoardOutdoor Unit CU-KE36NKU Other Component Specifications Dimensional Data Inchmm 194-00-1 Unit Indoor unit Outdoor unit Refrigerant Flow DiagramRefrigerant Flow Diagram Indoor Unit CS-KE30NKU Outdoor Unit CU-KE30NKUPerformance Data Temperature ChartsHigh pressure performance chart Indoor Unit CS-KE36NKU Outdoor Unit CU-KE36NKU Discharge 9535 8630 Indoor CU-KE30NKU Power Supply 230V Single Phase 60Hz Cooling CapacityCooling Capacity CS-KE30NKU34,000 BTU/h Outdoor Cooling Capacity Low Ambient30,900 30,870 30,800 30,710 30,590 30,400 30,210 Power Supply 230V Single Phase 60Hz Heating Capacity Heating CapacityTH Total Heating Capacity BTU/h 36,000 BTU/h Air Throw Distance Charts Cooling Heating Electrical CharacteristicsElectrical Data Voltage230V Cooling650 8FA2-5251-12400-1 Electric Wiring DiagramsController 8FA2-5251-15200-0Auto cooling/heating operation FunctionsOperation Functions Emergency operationLamp colors Timer backupSwitching Procedure to Noise Reducing Control Noise Reducing Control Outdoor UnitOperation Sound CU-KE36NKU Maximum Current Value Change ProcedureMaximum Current Value Change Function Description of functionFreeze prevention Compressor discharge temperature controlProtective Functions Overload prevention during heatingDefrost detection and release CT Peak current cut-off controlReverse-Cycle Defrosting Troubleshooting Before Calling for Service Precautions before Performing Inspection or RepairMethod of Self-Diagnostics Diagnosis Contents Self-diagnostics LampsNormal Replace the controllerReplace the circuit board or the fuse Using the TEST/T-RUN terminals Checking the Indoor and Outdoor UnitsChecking the indoor unit Control Check items unit operation Before the Operation Serial Communication Error Identification ProcedureAlarm Code E05 Off Blinking IlluminatedFrom the previous page a Alarm Code E07/P04/P05/P20/P27 Indoor Fan Motor Trouble Diagnosis of Fan MotorPin 2 PG white Outdoor Fan MotorPin 3 Gnd blue Pin 1 Vcc brownLocations most susceptible to noise Trouble Correction Noise Malfunction and Electromagnetic InterferenceNoise malfunction Electromagnetic interferenceMeasurement of Insulation Resistance for Electrical Parts Power Supply CordChecking Electrical Components Measurement of Insulation ResistanceChecking Continuity of Fuse on PCB Assy Characteristics Refrigerant R410A Special Precautions When Servicing UnitCharacteristics of New Refrigerant R410A What is New Refrigerant R410A?Checklist before Servicing Tools Specifically for R410A Tubing Installation ProceduresCase of Compressor Malfunction Procedure for Replacing CompressorTo prevent the composition Configuration and characteristics of cylindersAmount in the charging cylinder is less than 20% ExampleCase Refrigerant is Leaking Welding leaking pointsRecharging Use of Existing Units When Tubes are ExtendedCharging Additional Refrigerant Retro-Fitting Existing SystemsAppendix a Operating Instructions CS-KE36NKU CS-KE30NKUProduct Information FeaturesContents Safety PrecautionsAvoid Installation LocationSafety Instructions Electrical RequirementsUnit Display and Operation Button Names of PartsSymbols Remote Controller DisplayRemote Controller High Power button HR. Timer button 1-HOUR OFF TimerTemperature setting buttons Temp Mode selector button20 mm Using the Remote ControllerACL button 32 x 13/16Automatic Operation Operation with the Remote ControllerManual fan speed Cooling and DRY ModeHeating Mode Automatic fan speedUnoccupied Indication Status High Power ModeSpecial Remarks Operation Indication Setting the TimerUsing the 1-HOUR OFF Timer Tips for Energy Saving1030 pm 710 am 1100 am Present time When the air conditioner is not running Adjusting the Airflow DirectionWashing the front panel with water How to replace the filterCleaning the main unit and Remote Controller Removing and remounting the front panelWired Remote Controller Operating RangeTrouble Possible Cause Remedy Model No Outdoor Unit Indoor Unit SpecificationsPage 852-6-4190-587-00-0 Contents Installation Instructions Split System Air ConditionerPlease Read Before Starting Accidentally Fins of the outdoor unit. You may get injuredOptional Copper Tubing Kit Tools Required for Installation not suppliedAccessories Supplied with Unit Table GeneralAdditional Materials Required for Installation Installation Site SelectionSolid base must not cover the hole of the bottom plate Precautions for Installation in a Snowy Area  Countermeasures against snow and wind $/,8,3?,4508-25=  $/,04.3?-8,,D,4+89 Unit inch Required space around the outdoor unit 4922054=0/041,9-*04.52,9$/,-8544+5/90+,9398,30456,4 27-5/8 11-5/8 Air Intake 25/32 13/32 13-3/8 14-31/32  #04.2,4004922054  9*2,9545/90+,9 4522,8/4/,/,0./5-/,5+55840 9*2,9545/90+,9 Installation in front-rear rowsObstacles to the front and rear of unit  #04.2,4004922054Make a Hole How to Install the Indoor UnitTrical wiring or conduits are Remove the Rear Panel from the UnitHole Dia Install the Rear Panel on the WallIf Wooden Wall If Block, Brick, Concrete or Similar Type WallRemoving and Installing the Grille How to remove the grilleHow to replace the grille Shape the Indoor Side Tubing Wiring Instructions General precautions on wiringWire Size and Length Wiring Instructions for Inter-unit Connections How to connect wiring to the terminal For Indoor Unit For Outdoor Unit  For solid core wiring or F-cable For stranded wiring  Right-side tubing MountingSwitching drain hose and drain cap  Left-side tubingDrain cap Frame Fastening Method Do not supply power toTubing and wiring to the out To unmount indoor unitCover B How to Install the Outdoor UnitWiring Instructions for the Outdoor Unit Routing the Tubing and WiringUse of the Flaring Method Flaring Procedure with a Flare ToolTo 0.5 mm Adjust so that the amount of tube Refrigerant TubingTaping the Tubes Connecting Tubing between Indoor and Outdoor UnitsFinishing the Installation Insulation of Refrigerant TubingAir Purging Be sure to completely insert Hex wrench beforeAttempting to turn the valve How to Test Run the Air Conditioner  Pump Down  Basic Functions of the Service ValvesRemote Controller Installation Position  Service Valve ConnectionsAddress Setting of the Remote Controller Address SwitchDC1111-0

CS-KE30NKU, CS-KE36NKU, CU-KE30NKU, CU-KE36NKU specifications

The Panasonic CU-KE36NKU, CS-KE36NKU, CU-KE30NKU, and CS-KE30NKU air conditioning units represent the brand's commitment to delivering high-performance cooling solutions backed by innovative technologies. These units cater to both residential and commercial applications, ensuring users experience maximum comfort throughout the year.

One of the standout features of these models is their energy efficiency. Both units are equipped with advanced inverter technology, which allows for variable speed operation. This means they can adjust their power output according to the room's cooling needs, reducing energy consumption and minimizing electric bills while maintaining a consistent temperature. The models boast impressive SEER (Seasonal Energy Efficiency Ratio) ratings, making them environmentally friendly options.

Panasonic's nanoe-G technology is another remarkable feature incorporated into these models. This technology helps to purify the air by generating hydroxyl radicals, which eliminate airborne particles, odors, and harmful bacteria. This results in a healthier indoor environment, conducive to both comfort and well-being. The air purification aspect not only enhances the air quality but also extends the lifespan of the HVAC system by reducing the buildup of dust and contaminants.

In terms of user convenience, both the CU-KE and CS-KE series are equipped with programmable timers, allowing users to set their desired operation schedules. They also come with a remote control for ease of use, enabling adjustments from a distance. The installation process is straightforward, and the sleek design blends seamlessly with various interior aesthetics, making them a suitable choice for any room.

Durability is a key characteristic of Panasonic air conditioning units, and the CU-KE36NKU, CS-KE36NKU, CU-KE30NKU, and CS-KE30NKU are designed to withstand varying environmental conditions. Their robust construction ensures reliability and performance over the years. Additionally, both models come with a quiet operation feature that minimizes noise levels, allowing for comfortable use without disturbing daily activities.

In summary, the Panasonic CU-KE36NKU, CS-KE36NKU, CU-KE30NKU, and CS-KE30NKU are exceptional air conditioning units that combine energy efficiency, innovative purification technology, user-friendly features, and robust durability. These models are an ideal investment for anyone seeking a reliable and high-performance cooling solution.