Pride Mobility Quantum 500 manual Seat Installation, To install the seat, Controller Installation

Page 21

I V . A S S E M B L Y

SEAT INSTALLATION

Itmaybenecessarytoinstalltheseateitherpriortoinitialopera- tionoraftertransportingyourpowerchair.Ifyourpowerchairis equippedwithaspecialtyseatingsystem,refertotheinformation providedinseparatemanuals.Themedium-andhigh-backseats are attached to the power base with the Universal Mounting System(UMS).TheUMSconsistsofuniversalpartsthatmay be attached to the seat, regardless of seat width or seat depth. Thetwomaincomponentsarealuminumextrusionsmountedto the seat base. These extrusions attach to a pair of trapeze bars that are mounted to the power base. See figure 11.

WARNING! Do not pick up the seat frame by the armrests. They are free to pivot, and you may lose control of the seat if they do so, resulting in personal injury or damage to the chair.

To install the seat:

1.Set the trapeze bars to the desired height. To change the trapeze bar height, see V. “ComfortAdjustments.”

2.Tilt the seat back and slide the rear extrusion onto the rear trapeze bar. See figure 11.

3.Lower the front extrusion onto the front trapeze bar until the seat locks into place.

4.Flip the seat latch safety down.

WARNING! Make sure the seat latch safety isflippeddownbeforeusingyourpowerchair.

CONTROLLER INSTALLATION

Depending on the various configurations and options you have chosen for your power chair, it may have been shipped without the controller module installed in the armrest.

WARNING! Do not place the controller cable so that it can be pinched in the seat frame or power base frame.

SEAT

LATCH

SAFETY

REAR

EXTRUSION

FRONT

EXTRUSION

TRAPEZE

BARS

Figure 11. Universal Mounting System (Shown Without Armrests for Clarity)

1.Install the controller into the mounting block or under the armrest. See figure 17 or 18.

2.Tighten the setscrew(s).

3.Route the controller cable so that it cannot be pinched in the seat hinge.

4.Remove the rear lid to expose the electronics tray.

5.Plug the controller connector(s) into the power base. See figure 6.

6.Secure the controller cable to the armrest receiver with one or more wire ties.

Quantum 500

www.quantumrehab.com

21

Image 21

Contents Page F E T Y G U I D E L I N E S N T E N T S N T R O D U C T I O N PURCHASER’S AgreementInformation Exchange My Quantum Rehab Specialist Pride Owners ClubS a F E T Y Product Safety SymbolsS a F E T Y Modifications Pre-Ride Safety CheckWeight Limitations Tire InflationIncline Information Braking Information Cornering InformationPublic Streets and Roadways Outdoor Driving Surfaces Freewheel ModeStationary Obstacles Steps, Curbs, etc Stairs and EscalatorsDoors TransfersElevators Lift/Elevation ProductsMotor Vehicle Transport Inclement Weather PrecautionsPositioning Belts Reaching and BendingElectromagnetic and Radio Frequency Interference EMI/RFI AlcoholQuantum I . Y O U R P O W E R C H a I RQuantum 500 Specifications Electrical Components Quantum 500 Power BaseQuantum 500 Electrical Components To engage or disengage the drive motors Manual Freewheel LeversA S S E M B L Y Initial AssemblySeat Installation To install the seatController Installation Seat Height and Seat Angle Adjustment O M F O R T a D J U S T M E N T STo change the seat height To adjust the seatback angle Seatback Angle AdjustmentTo adjust the recline angle Seat PositionArmrest Angle Adjustment To change the armrest angle Armrest Width AdjustmentFoot Platform Depth To adjust the foot platform depth To change the armrest widthTo clamp the quick release fastener To adjust the foot platform angleFoot Platform Angle Controller PositionTo adjust the ELR angle To adjust the SFR lengthTo adjust the ELR length To adjust the forward/back positionMulti-Axis Foot Plate To adjust the leg rest lengthTo change leg rest length a To change foot plate position BBattery Break-in Tochargethebatteriesusingtheoff-boardchargerB a T T E R I E S a N D C H a R G I N G Batteries and ChargingCan I use a different battery charger? Frequently Asked Questions FAQs Howdoesthechargerwork?How often must I charge the batteries? Daily UseHow can I ensure maximum battery life? Why do my new batteries seem weak?How should I store my power chair and its batteries? What about public transportation?VSI Electronic Controller I . O P E R a T I O NVSI consists JoystickKeypad Battery Condition MeterOn/Off Key Red, yellow, and green lights lit Batteries chargedController Connector Motor ConnectorsBattery Connector Power Seat Actuator ConnectorThermal Rollback VSI Error CodesShould your power chair come in contact with water Care and MaintenanceTemperature I I . C a R E a N D M a I N T E N a N C EWeekly Checks Daily ChecksTo check the brakes Monthly ChecksCleaning Instructions Tire/Wheel Replacement Yearly ChecksStorage To replace the batteries Battery ReplacementBattery Installation Corrective Maintenance When to See Your Quantum Rehab Specialist for ServiceW a R R a N T Y Warranty Exclusions Reconditioned Units WarrantyService Checks and Warranty Service Exclusions also include components with damage caused byInspector Quality Control Quantum