Invacare Tracer Titan Heel Loop Replacement Figure, Swingaway Footrest Height Adjustment Figure

Page 16

PROCEDURE 1	FRONT RIGGINGS

F

R O N T

R

I

G G I N G S

This Procedure includes the following:

Swingaway Footrest Assembly Installation

Swingaway Footrest Height Adjustment

Heel Loop Replacement

Elevating Legrest Assembly Installation

Adjusting the Elevating Legrest Assembly

WARNING

After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or dam- age may result.

SWINGAWAY FOOTREST ASSEMBLY INSTALLATION (FIGURE 1)

1.Turn the swingaway footrest to the side (open footplate is perpendicular to wheelchair).

2.Place the hinge plates on the swingaway footrest onto the hinge pins on the wheelchair frame.

3.Push the swingaway footrest towards the inside of the wheelchair until it locks into place.

NOTE: The footplate will be on the inside of the wheel- chair when locked in place.

4.Repeat this procedure for the other footrest assembly.

5.To release the footrest, push the footrest release lever inward, rotate footrest outward.

	Hinge Plate	Footrest
		Footrest
		Release
		Lever
		Swingaway
Hinge		Footrest
Pins		Assembly
	Hinge	Footplate
	Hinge
	Plate

FIGURE 1 - SWINGAWAY FOOTREST

ASSEMBLY INSTALLATION

SWINGAWAY FOOTREST HEIGHT ADJUSTMENT (FIGURE 2)

NOTE: Release the footrest locking mechanism and lift the footrest off of the hinge pins. Lay the assembly on a flat surface to simplify this procedure.

1.Loosen, but do not remove the bolt and locknut that secure the lower footrest assembly to the upper footrest support.

2.Reposition the lower footrest assembly to the desired height.

3.Securely tighten the bolt and locknut.

4.Repeat this procedure for the other footrest, if necessary.

Upper	Bolt and	Lower
Footrest	Locknut	Lower
Support		Footrest
		Assembly

FIGURE 2 - SWINGAWAY FOOTREST HEIGHT

ADJUSTMENT

HEEL LOOP REPLACEMENT (FIGURE 3)

1.Loosen, but do not remove the bolt and locknut that secure the lower half of the footrest to the swingaway footrest assembly.

2.Remove the lower footrest assembly.

3.Remove the phillips screw, spacer and locknut that secure the heel loop to the footplate.

4.Remove heel loop from slide tube.

5.Replace heel loop.

6.Reverse STEPS 1-5to reassemble.

NOTE: When securing the heel loop to the footrest as- sembly, tighten the phillips screw and locknut until the spacer is secure.

16

Image 16

Contents Tracer R SX Tracer R SX Recliner Tracer R Titan Tracer R DLX I N G Table of Contents Special Notes Wheelchair TIE-DOWN Restraints and Seat Positioning StrapsSafety Summary Operating InformationTo Healthcare PROFESSIONALS/ASSISTANTS SAFETY/HANDLING of Wheelchairs Percentage of Weight DistributionStability and Balance Coping with Everyday ObstaclesFunctional Reach from a Wheelchair REACHING, Leaning Bending ForwardREACHING, Leaning Backwards Tipping Tipping Curbs Method 1 WheelchairWithout Step Tubes Tipping Curbs Method 1 Wheelchair with Step TubesStairways Transferring to and from Other SeatsFolding and Unfolding the Wheelchair OpeningRecliner Models ClosingSpecifications I F I C a T I O N ST I O N S Safety Inspection Checklist Initially Inspect Adjust Weekly Monthly PeriodicallyTroubleshooting MaintenanceMaintenance Safety Precautions Suggested Maintenance ProceduresSwingaway Footrest Assembly Installation Figure Heel Loop Replacement FigureSwingaway Footrest Height Adjustment Figure Elevating Legrest Assembly Installation Figure Adjusting the Elevating Legrest Assembly FigureWheelchairs Equipped With Height Adjustment Levers Figure Adjusting Armrest Height Adjustable Height Arms onlyWhelchairs Equipped With Height Adjustment Knobs Figure Using or Replacing FLIP-BACK Armrest Figure UsingRemoving or Replacing Armrest Figure ReplacingReplacing the SLIP-ON Back Upholstery Figure Assembling the Back Cane to the Wheelchair FigureReplacing SCREW-ON Back Upholstery Figure Adjusting Seat Width Figure Adjusting Seat Depth FigureReplacing Seat Upholstery Figure Tracer DLX Built Before March 13 Quick-Release Axles Figure REMOVING/INSTALLING the Rear WheelsPermanent Axles Figure Adjusting the QUICK-RELEASE Axle Figure REPLACING/REPAIRING Rear Wheel TIRE/TUBEReplacing Rear Wheel Handrim Figure REPLACING/REPAIRING Front Caster TIRE/TUBE Front Caster Mounting Adjustments FigureInstalling The Anti-tippers Figures 1 INSTALLING/ADJUSTING the ANTI-TIPPERSAdjusting The Anti-tippers Figure Wheel Lock Adjustment Figure Wheel Lock AdjustmentProcedure SEAT-TO-FLOOR Height Changing SEAT-TO-FLOOR HeightChanging SEAT-TO-FLOOR Height Recliner Frame Style Recliner Operation Figure C L I N E RReplacing the HEADREST/BACK Upholstery Replacing the Headrest Pillow FigureHeadrest Upholstery Figure Back Upholstery FigureInstalling REMOVING/INSTALLING the Spreader BAR FigureRemoving REMOVING/INSTALLING the Rear Wheels Figure REMOVING/INSTALLING Rear WheelsInstalling the Amputee Bracket Figure Installing the Amputee BracketInstalling the Crutch and Cane Carrier Figure Installing the Seat Positioning Strap FigureSafety and Maintenance Installing the Telescoping I.V. ROD MountingRepositioning The Upper Attachment Figure Repositioning the Upper MountPage Limited Warranty Tracer DLXOne Invacare Way