Invacare Pro Series manual INSTALLING/REMOVING Elevating Legrests Figure, Adjustable Footplate

Page 17

FOOTREST

PROCEDURE 1

 

 

6. Reverse preceding steps to reassemble.

NOTE: When securing the heel loop to the footrest as- sembly, tighten the phillips screw and locknut until the spacer is secure.

Adjustable Footplate

1.Remove the four (4) phillips screws and washers that secure the existing heel loop to the footplate.

2.Position the mounting holes of the new heel loop with the mounting holes in the adjustable footplate.

3.Secure the new heel loop to the footplate with the four

(4) phillips screws and washers.

INSTALLING/REMOVING ELEVATING LEGRESTS (FIGURE 9)

NOTE: Remove the legrests from the wheelchair by re- versing this procedure.

1.Insert the pivot tube into the legrest support and se- cure it with the bolt and nut.

2.Place legrest on the outside of the wheelchair and insert the mounting pin into the mounting tube.

3.Rotate legrest toward the inside of the wheelchair until it locks in place.

NOTE: The footplate will be on the inside of the wheelchair when locked in place.

4.Repeat STEPS 1-3for the opposite legrest.

5.After seated in wheelchair, adjust footrest to correct height by loosening nut and sliding the pivot tube up or down until desired height is obtained.

Calfpad Legrest

 

 

 

Release

Mounting Pin

 

 

Handle

 

 

 

 

 

 

 

 

 

Bolt and Nut

 

Footrest

 

Assembly

 

Pivot

 

Tube

 

Footplate

Mounting Tube

 

FIGURE 9 - INSTALLING ELEVATING

LEGRESTS

NOTE: Remove the footrests from the wheelchair by re- versing this procedure.

RAISING/LOWERING ELEVATING LEGRESTS AND/OR ADJUSTING CALFPADS (FIGURE 10)

Raising/Lowering Elevating Legrests

1.Perform one (1) of the following:

RAISING - Pull back on the release lever until the leg is at the desired height.

LOWERING - Support leg with one (1) hand and push release lever downward with other hand.

Adjusting Calfpads

1.To adjust the calfpad, turn pad towards the outside of the wheelchair.

2.Slide the calfpad up or down until the desired position is obtained.

3.To secure the calfpad, turn the calfpad towards the inside of the wheelchair.

Release Lever

Calfpad

Adjust Calfpad

Secure Calfpad

 

FIGURE 10 - RAISING/LOWERING

ELEVATING LEGRESTS AND/OR ADJUSTING

CALFPADS

F O O T R E S T

1 7

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Pro Pro-T Page Table of Contents Special Notes Special NotesSafety Summary Safety SummaryTire Pressure SAFETY/HANDLING of Wheelchairs Method StairwaysOther Seats Percentage of Weight DistributionTransferring to and from REACHING, Bending Backwards Functional Reach from a WheelchairREACHING, LEANING, Bending and Bending Forward Specifications SpecificationsSafety Inspection Check List Safety Inspection ChecklistMaintenance TroubleshootingMaintenance Safety Precautions TROUBLESHOOTING/MAINTENANCEAdjusting Footrest Height Figure INSTALLING/REMOVING Footrests FigureInstalling Adjustable Angle FLIP-UP Footplate Hinge Figure Procedure FootrestInstalling Adjustable Angle Flip-up Footplate Footrest ProcedureAdjustable Angle Flip-up Footplate Depth Adjustment Flip the footplate hinge to the UP positionComposite Footplates Replacing Heel Loops FigureImpact GUARDS/CALF Strap Figure Adjustable Footplate INSTALLING/REMOVING Elevating Legrests FigureAdjusting Calfpads Release Lever Calfpad Adjust Calfpad Secure CalfpadSaddle Bolts Footrest Installing Basketball Roller FigureCoved Washers Basketball Roller Locknuts Washers Basketball Roller TubeReplacing Seat Upholstery Figure Upholstery ProcedureBack Upholstery H O L S T E R YAdjustable Tension Back Upholstery AdjustingInstalling Adjustable Tension Back Upholstery Figure Back canesAdjustable Tension Straps Replacing Adjustable Tension Back Upholstery FigureH O L S T UpholsteryWHY USE Adjustable Tension Back Guard Installing Fabric Clothing Guards FigureFabric Clothing Procedure Frame Adjusting Back Height FigureM E FOLDING/UNFOLDING Back Folding Back Wheelchairs only FigureAdjusting Back Angle Folding Back Wheelchairs only Figure Adjusting Rear Seat Height FigureFrame Procedure Back Canes With Push HandlesBack Angle to Seat Rail Adjusting Half ARM Height Figure Installing Half ARM FigureArms Procedure Reinstall the washer and locknut onto the bottom hex screwINSTALLING/REMOVING the T-ARMS Figure Installing the T-ARM Sockets FigureProcedure Arms InstallingWidth Figure Adjusting the T-ARMSHeight Figure Depth FigureArm Clamp Arm Socket Reposition the arm tube on the T-arm postArm Sockets Figure Bottom Socket Screws Replacing the Locking Lever T-ARMS FigureAdjusting Flip Back Arms Figure Installing Flip Back Arms FigureLength HeightThreaded Half Clamp Installing Rigid Clothing Guards FigureGuard Slot INSTALLING/REPLACING Front Caster Forks Figure REPAIRING/REPLACING Pneumatic Caster TIRE/TUBEProcedure Casters S T E R SPro-SA Model Wheelchairs Figure Adjusting Front Caster HeadtubesRepositioning Caster Headtubes on Wheelchair Frame Figure Adjusting Caster Headtube Height Pro-SA Wheelchairs OnlyRepeat Steps 1-8for the opposite side of the wheel- chair ALL Pro Series Wheelchairs Except Pro-SA FigureProcedure For Repositioning the Front Caster Headtubes Casters ProcedurePRO-SA ALL PRO Series Wheelchairs Except PRO-SASpacer Caster Headtube Fork Stem Locknut Bolt Front Caster Installing QUICK-RELEASE Casters FigureRepeat Steps 1-4for the opposite side of the wheel- chair Rear Wheels Procedure REMOVING/INSTALLING Rear Wheels FigureAdjusting QUICK-RELEASE Axles Figure Adjusting QUAD-RELEASE Handles Figure Installing QUAD-RELEASE Axles FigureProcedure Rear Wheels And/or OutAdjusting Wheelbase Length Figure REPAIRING/REPLACING Pneumatic Rear Wheel TIRE/ TubeAdjusting Wheelbase Width Figure Removing the Play From the Rear WheelsJam Nuts Axle Mounting Plate Axle Bushing Adjusting Rear Wheel Camber FigureWasher Coved Axle Washers Mounting Locknut Plate One Wheelchair Three 3 Camber Frame WashersRear Wheelchair Centerline TOE-IN/TOE-OUT Alignment Figures 8Conditions exists Toe-out Toe-in Smaller Than Front Larger Than FrontCorrecting TOE-IN/TOE-OUT REPLACING/ADJUSTING the Wheel Lock FigureCondition Figure E E L SINSTALLING/ADJUSTING the ANTI-TIPPERS Figure Wheel Lock Extension Handle Installation FigureAdjusting the High/Undermount Wheel Lock Installing the Anti-tippersAdjust Adjusting the Anti-tipper HeightHeight Wheelchair Frame Anti-tipperAdjusting Handrims Spoke Rear Wheels Figure Installing/Replacing Handrims Spoke Rear Wheels FigureHandrims Phillips Screw HandrimLink Phillips Screw Rear Wheel HandrimComposite Rim Locknut Seat to Floor Height Determination Figures 1 Seat to Floor ProcedurePositioning Front Caster on the Fork Changing Seat to Floor HeightPositioning Caster Headtubes on the Wheelchair Frame Rear Seat to Floor Heights Caster Headtube Front Seat to Floor Heights PRO-SA only Seat to FloorprocedurePage A N T Y Limited WarrantyWarranty One Invacare Way
Top Page Image Contents