Invacare Pro Series manual Replacing the Locking Lever T-ARMS Figure, Bottom Socket Screws

Page 31

ARMS	PROCEDURE 4

3.Perform one (1) of the following:

Small Side Guards - Movethebottomclampupone

(1)of two (2) mounting posi- tions in the side guard.

Large Side Guards - Movethebottomclampupone

(1) of three (3) mounting posi- tions in the side guard.

4.Re-secure the side guard to the bottom clamp with the two bottom (2) socket screws.

5.Install the T-arm onto the wheelchair. Refer to IN- STALLING/REMOVING THE T-ARMSin this pro- cedure of the manual.

		Side	T-arm
	Socket	Guard	T-arm
		Guard

	Screws		Transfer
	Exploded		Transfer
	Exploded		Assist
	for Clarity,		Assist
	for Clarity,
	Do Not
	Remove

3.Remove the existing locking lever and spring from the bottom bracket.

NOTE: Inspect the spring and replace if necessary.

4.Position the spring on the bottom bracket as shown in FIGURE 9.

5.Position the new locking lever onto the spring and the bottom bracket.

NOTE: Make sure the two (2) extended ends of the spring are inside the notch in the locking lever.

6.Line up the mounting holes in the new locking le- ver, spring and bottom bracket.

WARNING

DO NOT over tighten the locknut that secures the locking lever to the bottom bracket. Over tightening this locknut will prevent the locking lever from op- erating properly, possibly causing injury.

7.Install the phillips bolt and tighten securely with the locknut.

8.Install the T-arm onto the wheelchair. Refer to IN- STALLING/REMOVING THE T-ARMSin this pro- cedure of the manual.

A R M S

Bottom
Socket
Screws	Bottom Clamp

FIGURE 8 - ADJUSTING THE TRANSFER ASSISTS AND/OR SIDE GUARDS - T-ARMS

REPLACING THE LOCKING LEVER - T-ARMS (FIGURE 9)

1. Remove the T-arm from the wheelchair. Refer to

INSTALLING/REMOVING THE T-ARMS in this

Bottom

Bracket

Phillips Bolt

Extended Ends

Spring

Notch

Locknut

Locking

Lever

procedure of the manual.

2. Remove the phillips bolt and locknut that secure

the existing locking lever to the bottom bracket.

NOTE: The locking lever is spring loaded. Place your free hand over the locking lever to prevent the parts from springing off of the bottom bracket.

FIGURE 9 - REPLACING THE LOCKING

LEVER - T-ARMS

3 1

Image 31

Contents Pro Pro-T Page Table of Contents Special Notes Special NotesSafety Summary Safety SummaryTire Pressure SAFETY/HANDLING of Wheelchairs Method StairwaysTransferring to and from Percentage of Weight DistributionOther Seats REACHING, LEANING, Bending and Bending Forward Functional Reach from a WheelchairREACHING, Bending Backwards Specifications SpecificationsSafety Inspection Check List Safety Inspection ChecklistTROUBLESHOOTING/MAINTENANCE TroubleshootingMaintenance Maintenance Safety PrecautionsProcedure Footrest INSTALLING/REMOVING Footrests FigureAdjusting Footrest Height Figure Installing Adjustable Angle FLIP-UP Footplate Hinge FigureFlip the footplate hinge to the UP position Footrest ProcedureInstalling Adjustable Angle Flip-up Footplate Adjustable Angle Flip-up Footplate Depth AdjustmentImpact GUARDS/CALF Strap Figure Replacing Heel Loops FigureComposite Footplates Release Lever Calfpad Adjust Calfpad Secure Calfpad INSTALLING/REMOVING Elevating Legrests FigureAdjustable Footplate Adjusting CalfpadsWashers Basketball Roller Tube Installing Basketball Roller FigureSaddle Bolts Footrest Coved Washers Basketball Roller LocknutsH O L S T E R Y Upholstery ProcedureReplacing Seat Upholstery Figure Back UpholsteryBack canes AdjustingAdjustable Tension Back Upholstery Installing Adjustable Tension Back Upholstery FigureUpholstery Replacing Adjustable Tension Back Upholstery FigureAdjustable Tension Straps H O L S TWHY USE Adjustable Tension Back Fabric Clothing Installing Fabric Clothing Guards FigureGuard FOLDING/UNFOLDING Back Folding Back Wheelchairs only Figure Adjusting Back Height FigureProcedure Frame M EBack Canes With Push Handles Adjusting Rear Seat Height FigureAdjusting Back Angle Folding Back Wheelchairs only Figure Frame ProcedureBack Angle to Seat Rail Reinstall the washer and locknut onto the bottom hex screw Installing Half ARM FigureAdjusting Half ARM Height Figure Arms ProcedureInstalling Installing the T-ARM Sockets FigureINSTALLING/REMOVING the T-ARMS Figure Procedure ArmsDepth Figure Adjusting the T-ARMSWidth Figure Height FigureArm Sockets Figure Reposition the arm tube on the T-arm postArm Clamp Arm Socket Bottom Socket Screws Replacing the Locking Lever T-ARMS FigureHeight Installing Flip Back Arms FigureAdjusting Flip Back Arms Figure LengthGuard Slot Installing Rigid Clothing Guards FigureThreaded Half Clamp S T E R S REPAIRING/REPLACING Pneumatic Caster TIRE/TUBEINSTALLING/REPLACING Front Caster Forks Figure Procedure CastersPro-SA Model Wheelchairs Figure Adjusting Front Caster HeadtubesALL Pro Series Wheelchairs Except Pro-SA Figure Adjusting Caster Headtube Height Pro-SA Wheelchairs OnlyRepositioning Caster Headtubes on Wheelchair Frame Figure Repeat Steps 1-8for the opposite side of the wheel- chairALL PRO Series Wheelchairs Except PRO-SA Casters ProcedureProcedure For Repositioning the Front Caster Headtubes PRO-SARepeat Steps 1-4for the opposite side of the wheel- chair Installing QUICK-RELEASE Casters FigureSpacer Caster Headtube Fork Stem Locknut Bolt Front Caster Adjusting QUICK-RELEASE Axles Figure REMOVING/INSTALLING Rear Wheels FigureRear Wheels Procedure And/or Out Installing QUAD-RELEASE Axles FigureAdjusting QUAD-RELEASE Handles Figure Procedure Rear WheelsRemoving the Play From the Rear Wheels REPAIRING/REPLACING Pneumatic Rear Wheel TIRE/ TubeAdjusting Wheelbase Length Figure Adjusting Wheelbase Width FigureWheelchair Three 3 Camber Frame Washers Adjusting Rear Wheel Camber FigureJam Nuts Axle Mounting Plate Axle Bushing Washer Coved Axle Washers Mounting Locknut Plate OneToe-out Toe-in Smaller Than Front Larger Than Front TOE-IN/TOE-OUT Alignment Figures 8Rear Wheelchair Centerline Conditions existsE E L S REPLACING/ADJUSTING the Wheel Lock FigureCorrecting TOE-IN/TOE-OUT Condition FigureInstalling the Anti-tippers Wheel Lock Extension Handle Installation FigureINSTALLING/ADJUSTING the ANTI-TIPPERS Figure Adjusting the High/Undermount Wheel LockWheelchair Frame Anti-tipper Adjusting the Anti-tipper HeightAdjust HeightPhillips Screw Handrim Installing/Replacing Handrims Spoke Rear Wheels FigureAdjusting Handrims Spoke Rear Wheels Figure HandrimsComposite Rim Locknut Phillips Screw Rear Wheel HandrimLink Seat to Floor Height Determination Figures 1 Seat to Floor ProcedurePositioning Caster Headtubes on the Wheelchair Frame Changing Seat to Floor HeightPositioning Front Caster on the Fork Rear Seat to Floor Heights Caster Headtube Front Seat to Floor Heights PRO-SA only Seat to FloorprocedurePage Warranty Limited WarrantyA N T Y One Invacare Way