Invacare Pro Series manual Back canes, Back Upholstery Fastening Flap Canes, Adjusting

Page 20

PROCEDURE 2	UPHOLSTERY

U P H O L S T E R Y

NOTE: The back canes must be mounted in the same height adjustment hole.

5.Securely tighten the new/existing back upholstery to the back canes with the two (2) phillips screws and washers.

6.Secure the bottom of the new/existing back uphol- stery to the wheelchair frame with tie-wraps.

Removing/Installing Optional Back

Upholstery - Back Canes Without Push

Handles (FIGURE 3)

REMOVING.

1.Unlatch the two (2) fastening flaps that secure the bottom of the existing back upholstery to the back canes.

2.Lift up on the top of the existing back upholstery to unlatch.

3.Lift up on the existing back upholstery and remove from the wheelchair.

4.Installthenew/existingbackupholsteryontothewheel- chair. Refer to the following procedure.

INSTALLING.

1.Position the new/existing back upholstery over the two

(2) back canes.

2.Securely latch the fastening flaps on the bottom of the new back upholstery to the back canes.

3.Adjust theNEW backupholsteryto the desired height. Refer to the following procedure.

Back Upholstery

Fastening

Flap

Fastening

Flap

Back

Canes

FIGURE 3 - BACK UPHOLSTERY -

REMOVING/INSTALLINGADJUSTING OPTIONAL BACK UPHOLSTERY - BACK CANES WITHOUT PUSH HANDLES

ADJUSTING.

1.Unfold the top of the back upholstery.

2.Adjust the back upholstery to the desired height.

3.Resecure the top of the back upholstery.

Adjustable Tension Back Upholstery

INSTALLING ADJUSTABLE TENSION BACK UPHOLSTERY (FIGURE 4).

1.Remove the existing back upholstery from the wheelchair. Refer to REMOVING/INSTALLING

OPTIONAL BACK UPHOLSTERY - BACK CANES WITH PUSH HANDLES, REMOVING/ INSTALLING OPTIONAL BACK UPHOLSTERY - BACK CANES WITHOUT PUSH HANDLES or

REPLACING ADJUSTABLE TENSION BACK UPHOLSTERY in this procedure of the manual.

2.Slide each section (anchor loop/adjuster strap) of the adjustable tension back upholstery onto the two

(2) back canes with the grommet hole facing the rear of the wheelchair.

3.Secure the adjustable tension back upholstery to the back canes with the mounting screws and washers.

NOTE: Clean the upholstery with warm water and mild detergent to remove superficial soil.

Fastening Strap

Back Upholstery Cover

Fastening Strap

Adjustable Tension

Back Upholstery

Frame

Anchor Loops

Adjuster

Straps

Mounting Screws

Washers Grommet Hole

FIGURE 4 - ADJUSTABLE TENSION BACK UPHOLSTERY - INSTALLING/REPLACING ADJUSTABLE TENSION BACK UPHOLSTERY

2 0

Image 20

Contents Pro Pro-T Page Table of Contents Special Notes Special NotesSafety Summary Safety SummaryTire Pressure SAFETY/HANDLING of Wheelchairs Stairways MethodOther Seats Percentage of Weight DistributionTransferring to and from REACHING, Bending Backwards Functional Reach from a WheelchairREACHING, LEANING, Bending and Bending Forward Specifications SpecificationsSafety Inspection Checklist Safety Inspection Check ListTroubleshooting MaintenanceMaintenance Safety Precautions TROUBLESHOOTING/MAINTENANCEINSTALLING/REMOVING Footrests Figure Adjusting Footrest Height FigureInstalling Adjustable Angle FLIP-UP Footplate Hinge Figure Procedure FootrestFootrest Procedure Installing Adjustable Angle Flip-up FootplateAdjustable Angle Flip-up Footplate Depth Adjustment Flip the footplate hinge to the UP positionComposite Footplates Replacing Heel Loops FigureImpact GUARDS/CALF Strap Figure INSTALLING/REMOVING Elevating Legrests Figure Adjustable FootplateAdjusting Calfpads Release Lever Calfpad Adjust Calfpad Secure CalfpadInstalling Basketball Roller Figure Saddle Bolts FootrestCoved Washers Basketball Roller Locknuts Washers Basketball Roller TubeUpholstery Procedure Replacing Seat Upholstery FigureBack Upholstery H O L S T E R YAdjusting Adjustable Tension Back UpholsteryInstalling Adjustable Tension Back Upholstery Figure Back canesReplacing Adjustable Tension Back Upholstery Figure Adjustable Tension StrapsH O L S T UpholsteryWHY USE Adjustable Tension Back Guard Installing Fabric Clothing Guards FigureFabric Clothing Adjusting Back Height Figure Procedure FrameM E FOLDING/UNFOLDING Back Folding Back Wheelchairs only FigureAdjusting Rear Seat Height Figure Adjusting Back Angle Folding Back Wheelchairs only FigureFrame Procedure Back Canes With Push HandlesBack Angle to Seat Rail Installing Half ARM Figure Adjusting Half ARM Height FigureArms Procedure Reinstall the washer and locknut onto the bottom hex screwInstalling the T-ARM Sockets Figure INSTALLING/REMOVING the T-ARMS FigureProcedure Arms InstallingAdjusting the T-ARMS Width FigureHeight Figure Depth FigureArm Clamp Arm Socket Reposition the arm tube on the T-arm postArm Sockets Figure Replacing the Locking Lever T-ARMS Figure Bottom Socket ScrewsInstalling Flip Back Arms Figure Adjusting Flip Back Arms FigureLength HeightThreaded Half Clamp Installing Rigid Clothing Guards FigureGuard Slot REPAIRING/REPLACING Pneumatic Caster TIRE/TUBE INSTALLING/REPLACING Front Caster Forks FigureProcedure Casters S T E R SAdjusting Front Caster Headtubes Pro-SA Model Wheelchairs FigureAdjusting Caster Headtube Height Pro-SA Wheelchairs Only Repositioning Caster Headtubes on Wheelchair Frame FigureRepeat Steps 1-8for the opposite side of the wheel- chair ALL Pro Series Wheelchairs Except Pro-SA FigureCasters Procedure Procedure For Repositioning the Front Caster HeadtubesPRO-SA ALL PRO Series Wheelchairs Except PRO-SASpacer Caster Headtube Fork Stem Locknut Bolt Front Caster Installing QUICK-RELEASE Casters FigureRepeat Steps 1-4for the opposite side of the wheel- chair Rear Wheels Procedure REMOVING/INSTALLING Rear Wheels FigureAdjusting QUICK-RELEASE Axles Figure Installing QUAD-RELEASE Axles Figure Adjusting QUAD-RELEASE Handles FigureProcedure Rear Wheels And/or OutREPAIRING/REPLACING Pneumatic Rear Wheel TIRE/ Tube Adjusting Wheelbase Length FigureAdjusting Wheelbase Width Figure Removing the Play From the Rear WheelsAdjusting Rear Wheel Camber Figure Jam Nuts Axle Mounting Plate Axle BushingWasher Coved Axle Washers Mounting Locknut Plate One Wheelchair Three 3 Camber Frame WashersTOE-IN/TOE-OUT Alignment Figures 8 Rear Wheelchair CenterlineConditions exists Toe-out Toe-in Smaller Than Front Larger Than FrontREPLACING/ADJUSTING the Wheel Lock Figure Correcting TOE-IN/TOE-OUTCondition Figure E E L SWheel Lock Extension Handle Installation Figure INSTALLING/ADJUSTING the ANTI-TIPPERS FigureAdjusting the High/Undermount Wheel Lock Installing the Anti-tippersAdjusting the Anti-tipper Height AdjustHeight Wheelchair Frame Anti-tipperInstalling/Replacing Handrims Spoke Rear Wheels Figure Adjusting Handrims Spoke Rear Wheels FigureHandrims Phillips Screw HandrimLink Phillips Screw Rear Wheel HandrimComposite Rim Locknut Seat to Floor Procedure Seat to Floor Height Determination Figures 1Positioning Front Caster on the Fork Changing Seat to Floor HeightPositioning Caster Headtubes on the Wheelchair Frame Rear Seat to Floor Heights Caster Headtube Seat to Floorprocedure Front Seat to Floor Heights PRO-SA onlyPage A N T Y Limited WarrantyWarranty One Invacare Way