Invacare Pro Series manual Reposition the arm tube on the T-arm post, Arm Sockets Figure

Page 30

PROCEDURE 4

ARMS

 

 

 

A R M S

3.Reposition the arm tube on the T-arm post:

A.Desk Length Arms - to one (1) of three (3) posi- tions depending on the desired arm pad depth.

B.Full Length Arms - to one (1) of five (5) posi- tions depending on the desired arm pad depth.

NOTE: Additional positions are obtainable by turning the arm tube 180o.

4.Re-secure the arm tube to the T-arm post with the two (2) socket screws. Tighten securely.

5.Reattach the arm pad to the arm tube with the two

(2) phillips screws. Tighten securely.

6.Repeat for the opposite side, if necessary.

Arm Pad

6.Squeeze the T-arm socket together until the socket is flush with the T-arm.

7.While holding the T-arm socket together, tighten the four (4) hex screws and washers securely.

8.Press in on the locking lever and lift the T-arm straight up and out of the T-arm socket.

9.Repeat STEPS5-7,ifnecessaryuntiltheT-armslides in the T-arm socket as desired.

10.Reinstall the T-arm socket onto the wheelchair. Refer to INSTALLING THE T-ARM SOCKETS in this pro- cedure of the manual.

Hex Screws

Optional Locking Pins

Wheelchair Frame

Washers

Socket

Arm Tube

Screws

NOTE: If

 

Phillips

necessary, turn

arm tube 180o

Screw

to obtain two (2)

T-arm

positions.

 

Post

Phillips Screw

FIGURE 6 - ADJUSTING THE T-ARMS -

DEPTH

T-arm Sockets (FIGURE 7)

1.Remove the rear wheels from the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in PROCEDURE 6 of this manual.

2.Remove the three (3) hex screws and washers that secure the T-arm socket and T-arm clamp to the wheelchair frame and remove the T-arm socket from the wheelchair.

3.Ifequippedwithoptionallockingpins,removethelock- ing pins that secure the T-arm socket to the wheel- chair frame.

4.Loosen, but do not remove the four (4) hex screws and washers that secure the T-arm socket together.

NOTE: The T-arm socket will disassemble if the four (4) hex screws and washers are removed.

5.Slide the T-arm into the T-arm socket until the lock lever is in the slot in the T-arm socket and an audible "click" is heard.

T-arm Clamp

T-arm Socket

 

T-arm

Hex Screws

 

and Washers

 

T-arm

Hex Screws

Socket

and Washers

 

FIGURE 7 - ADJUSTING THE T-ARMS -

 

T-ARM SOCKETS

ADJUSTING THE TRANSFER ASSISTS AND/OR SIDE GUARDS - T-ARMS (FIGURE 8)

1.Remove the T-arm from the wheelchair. Refer to INSTALLING/REMOVING THE T-ARMSin this procedure of the manual.

2.Remove the two (2) bottom socket screws that secure the side guard to the bottom clamp.

3 0

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Pro Pro-T Page Table of Contents Special Notes Special NotesSafety Summary Safety SummaryTire Pressure SAFETY/HANDLING of Wheelchairs Stairways MethodPercentage of Weight Distribution Transferring to and fromOther Seats Functional Reach from a Wheelchair REACHING, LEANING, Bending and Bending ForwardREACHING, Bending Backwards Specifications SpecificationsSafety Inspection Checklist Safety Inspection Check ListMaintenance Safety Precautions TroubleshootingMaintenance TROUBLESHOOTING/MAINTENANCEInstalling Adjustable Angle FLIP-UP Footplate Hinge Figure INSTALLING/REMOVING Footrests FigureAdjusting Footrest Height Figure Procedure FootrestAdjustable Angle Flip-up Footplate Depth Adjustment Footrest ProcedureInstalling Adjustable Angle Flip-up Footplate Flip the footplate hinge to the UP positionReplacing Heel Loops Figure Impact GUARDS/CALF Strap FigureComposite Footplates Adjusting Calfpads INSTALLING/REMOVING Elevating Legrests FigureAdjustable Footplate Release Lever Calfpad Adjust Calfpad Secure CalfpadCoved Washers Basketball Roller Locknuts Installing Basketball Roller FigureSaddle Bolts Footrest Washers Basketball Roller TubeBack Upholstery Upholstery ProcedureReplacing Seat Upholstery Figure H O L S T E R YInstalling Adjustable Tension Back Upholstery Figure AdjustingAdjustable Tension Back Upholstery Back canesH O L S T Replacing Adjustable Tension Back Upholstery FigureAdjustable Tension Straps UpholsteryWHY USE Adjustable Tension Back Installing Fabric Clothing Guards Figure Fabric ClothingGuard M E Adjusting Back Height FigureProcedure Frame FOLDING/UNFOLDING Back Folding Back Wheelchairs only FigureFrame Procedure Adjusting Rear Seat Height FigureAdjusting Back Angle Folding Back Wheelchairs only Figure Back Canes With Push HandlesBack Angle to Seat Rail Arms Procedure Installing Half ARM FigureAdjusting Half ARM Height Figure Reinstall the washer and locknut onto the bottom hex screwProcedure Arms Installing the T-ARM Sockets FigureINSTALLING/REMOVING the T-ARMS Figure InstallingHeight Figure Adjusting the T-ARMSWidth Figure Depth FigureReposition the arm tube on the T-arm post Arm Sockets FigureArm Clamp Arm Socket Replacing the Locking Lever T-ARMS Figure Bottom Socket ScrewsLength Installing Flip Back Arms FigureAdjusting Flip Back Arms Figure HeightInstalling Rigid Clothing Guards Figure Guard SlotThreaded Half Clamp Procedure Casters REPAIRING/REPLACING Pneumatic Caster TIRE/TUBEINSTALLING/REPLACING Front Caster Forks Figure S T E R SAdjusting Front Caster Headtubes Pro-SA Model Wheelchairs FigureRepeat Steps 1-8for the opposite side of the wheel- chair Adjusting Caster Headtube Height Pro-SA Wheelchairs OnlyRepositioning Caster Headtubes on Wheelchair Frame Figure ALL Pro Series Wheelchairs Except Pro-SA FigurePRO-SA Casters ProcedureProcedure For Repositioning the Front Caster Headtubes ALL PRO Series Wheelchairs Except PRO-SAInstalling QUICK-RELEASE Casters Figure Repeat Steps 1-4for the opposite side of the wheel- chairSpacer Caster Headtube Fork Stem Locknut Bolt Front Caster REMOVING/INSTALLING Rear Wheels Figure Adjusting QUICK-RELEASE Axles FigureRear Wheels Procedure Procedure Rear Wheels Installing QUAD-RELEASE Axles FigureAdjusting QUAD-RELEASE Handles Figure And/or OutAdjusting Wheelbase Width Figure REPAIRING/REPLACING Pneumatic Rear Wheel TIRE/ TubeAdjusting Wheelbase Length Figure Removing the Play From the Rear WheelsWasher Coved Axle Washers Mounting Locknut Plate One Adjusting Rear Wheel Camber FigureJam Nuts Axle Mounting Plate Axle Bushing Wheelchair Three 3 Camber Frame WashersConditions exists TOE-IN/TOE-OUT Alignment Figures 8Rear Wheelchair Centerline Toe-out Toe-in Smaller Than Front Larger Than FrontCondition Figure REPLACING/ADJUSTING the Wheel Lock FigureCorrecting TOE-IN/TOE-OUT E E L SAdjusting the High/Undermount Wheel Lock Wheel Lock Extension Handle Installation FigureINSTALLING/ADJUSTING the ANTI-TIPPERS Figure Installing the Anti-tippersHeight Adjusting the Anti-tipper HeightAdjust Wheelchair Frame Anti-tipperHandrims Installing/Replacing Handrims Spoke Rear Wheels FigureAdjusting Handrims Spoke Rear Wheels Figure Phillips Screw HandrimPhillips Screw Rear Wheel Handrim Composite Rim LocknutLink Seat to Floor Procedure Seat to Floor Height Determination Figures 1Changing Seat to Floor Height Positioning Caster Headtubes on the Wheelchair FramePositioning Front Caster on the Fork Rear Seat to Floor Heights Caster Headtube Seat to Floorprocedure Front Seat to Floor Heights PRO-SA onlyPage Limited Warranty WarrantyA N T Y One Invacare Way
Top Page Image Contents