Invacare Pro Series Installing QUAD-RELEASE Axles Figure, Adjusting QUAD-RELEASE Handles Figure

Page 40

PROCEDURE 6

REAR WHEELS

 

 

R

E

A

R

W

H

E

E

L

S

INSTALLING QUAD-RELEASE AXLES (FIGURE 3)

1.Remove rear wheel and the existing quick-release axle from the wheelchair. Refer to REMOVING INSTALLING REAR WHEELS in this procedure of the manual.

2.Remove the existing quick-release axle from the rear wheel hub.

3.Insert the new quad-release axle through the rear wheel hub.

4.Slide the locking collar onto the quad-release axle until it is snug against the rear wheel and tighten securely with the allen screw.

5.Reinstall rear wheel and the quad-release axle onto the wheelchair.

WARNING

Make sure the detent pin and locking pins of the quad-release axle are fully released BEFORE operating wheelchair.

Keep locking pins clean.

6.

Flip the handle of the quad-release axle down to

 

release the detent pin ensuring that the locking pins

 

are fully released.

7.

If detent pin does not fully release, proceed to AD-

 

JUSTING THE QUAD-RELEASE HANDLE IN

 

AND/OR OUT.

2.Loosen the locking screw.

3.Perform one (1) of the following:

A.If the quad-release handle is not releasing the locking pins completely, rotate the quad-release handle approximately one- quarter (1/4) turn CLOCKWISE.

B.If the quad-release handle hits the spokes of the rear wheel when assembled, rotate the quad-release handle approximately one- quarter (1/4) turn COUNTERCLOCKWISE.

4.Tighten the locking screw securely.

5.Reinstall the rear wheel and quad-release axle onto the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this procedure of the manual.

WARNING

Make sure the detent pin and locking pins of the quad-release axle are fully released BEFORE operating the wheelchair.

Keep locking pins clean.

6.Flip the handle of the quad-release axle down to re- lease the detent pin ensuring that the locking pins are fully released.

7.Repeat the above procedures until the quad-release axle locks correctly.

ADJUSTING QUAD-RELEASE HANDLE IN/

AND OR OUT

8. Repeat STEPS 1-7for the opposite rear wheel.

Quad-Release

Allen Screw Axle Mounting

Axle

Plate

Quad-Release

Handle

Locking Pins

Locking Collar

Rear Wheel Hub

FIGURE 3 - INSTALLING QUAD-RELEASE

AXLES

ADJUSTING QUAD-RELEASE HANDLES (FIGURE 4)

In and/or Out

1.Remove rear wheel and the quad-release axle from the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this procedure of the manual.

Axle Mounting Plate

Locking Screw

REMOVING

PLAY FROM THE

REAR WHEELS

Length Adjustment Screw

FIGURE 4 - ADJUSTING QUAD-RELEASE

HANDLES

4 0

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Pro Pro-T Page Table of Contents Special Notes Special NotesSafety Summary Safety SummaryTire Pressure SAFETY/HANDLING of Wheelchairs Stairways MethodTransferring to and from Percentage of Weight DistributionOther Seats REACHING, LEANING, Bending and Bending Forward Functional Reach from a WheelchairREACHING, Bending Backwards Specifications SpecificationsSafety Inspection Checklist Safety Inspection Check ListTroubleshooting MaintenanceMaintenance Safety Precautions TROUBLESHOOTING/MAINTENANCEINSTALLING/REMOVING Footrests Figure Adjusting Footrest Height FigureInstalling Adjustable Angle FLIP-UP Footplate Hinge Figure Procedure FootrestFootrest Procedure Installing Adjustable Angle Flip-up FootplateAdjustable Angle Flip-up Footplate Depth Adjustment Flip the footplate hinge to the UP positionImpact GUARDS/CALF Strap Figure Replacing Heel Loops FigureComposite Footplates INSTALLING/REMOVING Elevating Legrests Figure Adjustable FootplateAdjusting Calfpads Release Lever Calfpad Adjust Calfpad Secure CalfpadInstalling Basketball Roller Figure Saddle Bolts FootrestCoved Washers Basketball Roller Locknuts Washers Basketball Roller TubeUpholstery Procedure Replacing Seat Upholstery FigureBack Upholstery H O L S T E R YAdjusting Adjustable Tension Back UpholsteryInstalling Adjustable Tension Back Upholstery Figure Back canesReplacing Adjustable Tension Back Upholstery Figure Adjustable Tension StrapsH O L S T UpholsteryWHY USE Adjustable Tension Back Fabric Clothing Installing Fabric Clothing Guards FigureGuard Adjusting Back Height Figure Procedure FrameM E FOLDING/UNFOLDING Back Folding Back Wheelchairs only FigureAdjusting Rear Seat Height Figure Adjusting Back Angle Folding Back Wheelchairs only FigureFrame Procedure Back Canes With Push HandlesBack Angle to Seat Rail Installing Half ARM Figure Adjusting Half ARM Height FigureArms Procedure Reinstall the washer and locknut onto the bottom hex screwInstalling the T-ARM Sockets Figure INSTALLING/REMOVING the T-ARMS FigureProcedure Arms InstallingAdjusting the T-ARMS Width FigureHeight Figure Depth FigureArm Sockets Figure Reposition the arm tube on the T-arm postArm Clamp Arm Socket Replacing the Locking Lever T-ARMS Figure Bottom Socket ScrewsInstalling Flip Back Arms Figure Adjusting Flip Back Arms FigureLength HeightGuard Slot Installing Rigid Clothing Guards FigureThreaded Half Clamp REPAIRING/REPLACING Pneumatic Caster TIRE/TUBE INSTALLING/REPLACING Front Caster Forks FigureProcedure Casters S T E R SAdjusting Front Caster Headtubes Pro-SA Model Wheelchairs FigureAdjusting Caster Headtube Height Pro-SA Wheelchairs Only Repositioning Caster Headtubes on Wheelchair Frame FigureRepeat Steps 1-8for the opposite side of the wheel- chair ALL Pro Series Wheelchairs Except Pro-SA FigureCasters Procedure Procedure For Repositioning the Front Caster HeadtubesPRO-SA ALL PRO Series Wheelchairs Except PRO-SARepeat Steps 1-4for the opposite side of the wheel- chair Installing QUICK-RELEASE Casters FigureSpacer Caster Headtube Fork Stem Locknut Bolt Front Caster Adjusting QUICK-RELEASE Axles Figure REMOVING/INSTALLING Rear Wheels FigureRear Wheels Procedure Installing QUAD-RELEASE Axles Figure Adjusting QUAD-RELEASE Handles FigureProcedure Rear Wheels And/or OutREPAIRING/REPLACING Pneumatic Rear Wheel TIRE/ Tube Adjusting Wheelbase Length FigureAdjusting Wheelbase Width Figure Removing the Play From the Rear WheelsAdjusting Rear Wheel Camber Figure Jam Nuts Axle Mounting Plate Axle BushingWasher Coved Axle Washers Mounting Locknut Plate One Wheelchair Three 3 Camber Frame WashersTOE-IN/TOE-OUT Alignment Figures 8 Rear Wheelchair CenterlineConditions exists Toe-out Toe-in Smaller Than Front Larger Than FrontREPLACING/ADJUSTING the Wheel Lock Figure Correcting TOE-IN/TOE-OUTCondition Figure E E L SWheel Lock Extension Handle Installation Figure INSTALLING/ADJUSTING the ANTI-TIPPERS FigureAdjusting the High/Undermount Wheel Lock Installing the Anti-tippersAdjusting the Anti-tipper Height AdjustHeight Wheelchair Frame Anti-tipperInstalling/Replacing Handrims Spoke Rear Wheels Figure Adjusting Handrims Spoke Rear Wheels FigureHandrims Phillips Screw HandrimComposite Rim Locknut Phillips Screw Rear Wheel HandrimLink Seat to Floor Procedure Seat to Floor Height Determination Figures 1Positioning Caster Headtubes on the Wheelchair Frame Changing Seat to Floor HeightPositioning Front Caster on the Fork Rear Seat to Floor Heights Caster Headtube Seat to Floorprocedure Front Seat to Floor Heights PRO-SA onlyPage Warranty Limited WarrantyA N T Y One Invacare Way
Top Page Image Contents