Invacare Pro Series manual O T R E S T, INSTALLING/REMOVING Footrests Figure, Procedure Footrest

Page 14

PROCEDURE 1

FOOTREST

 

 

F O O T R E S T

This Procedure includes the following:

Installing/Removing Footrest(s) Adjusting Footrest Height

Installing Adjustable Flip-Up Footplate Hinge

Installing/Adjusting Adjustable Angle Flip-Up Footplates

Impact Guards/Calf Strap Replacing Heel Loops Installing/Removing Elevating Legrests

Raising/Lowering Elevating Legrests and/or Adjusting Calfpads

Installing Basketball Roller

WARNING

After adjustments and BEFORE use, make sure all attaching hardware is securely tightened, otherwise injury or damage may occur.

NOTE: The following procedures are for Pro-SA Model Wheelchairs only, except where specified.

INSTALLING/REMOVING

FOOTREST(S) (FIGURE 1)

NOTE: Remove the footrests from the wheelchair by re- versing this procedure.

1.Turn the footrest to the side (open footplate is perpen- dicular to wheelchair).

2.Insert footrest mounting pin into mounting tube.

3.Push the footrest towards the inside of the wheel- chair until it locks into place.

NOTE: The footplate will be on the inside of the wheelchair when locked in place.

Footrest Mounting Pin

Footrest Release Lever

Mounting Tube

FIGURE 1 - INSTALLING/REMOVING

FOOTREST(S)

4.Repeat this procedure for other footrest assembly.

5.To release the footrest, push the footrest release le- ver inward, rotate footrest outward.

ADJUSTING FOOTREST HEIGHT (FIGURE 2)

NOTE: Release the footrest locking mechanism and lift the footrest mounting pins out of its mounting tube. Lay the assembly on a flat surface to simplify this procedure.

NOTE: Make sure to note the position of the washers before disassembly.

1.Remove impact guards and/or calf strap, if neces- sary.

2.Remove the hex screw and coved washer and posi- tion the footrest assembly to a determined height.

3.Lineup the mounting hole in the footrest frame, rein- sert the hex screw and coved washer; hand-tighten.

4.Securely tighten the hex screw and coved washer.

5.Repeat this procedure for the other footrest, if neces- sary.

6.Replace impact guards and/or calf strap, if neces- sary.

Coved Washer

Hex Screw

Footrest

FIGURE 2 - ADJUSTING FOOTREST HEIGHT

INSTALLING ADJUSTABLE ANGLE FLIP-UP FOOTPLATE HINGE (FIGURE 3)

NOTE: This procedure is for individual adjustable angle footrests only.

1.Position the adjustable angle flip-up footplate (footplate) hinge on the footrest support tube at the desired height.

2.Position the hardware on the footrest support as shown in FIGURE 3.

1 4

Image 14
Contents Pro Pro-T Page Table of Contents Special Notes Special NotesSafety Summary Safety SummaryTire Pressure SAFETY/HANDLING of Wheelchairs Stairways MethodOther Seats Percentage of Weight DistributionTransferring to and from REACHING, Bending Backwards Functional Reach from a WheelchairREACHING, LEANING, Bending and Bending Forward Specifications SpecificationsSafety Inspection Checklist Safety Inspection Check ListMaintenance Safety Precautions TroubleshootingMaintenance TROUBLESHOOTING/MAINTENANCEInstalling Adjustable Angle FLIP-UP Footplate Hinge Figure INSTALLING/REMOVING Footrests FigureAdjusting Footrest Height Figure Procedure FootrestAdjustable Angle Flip-up Footplate Depth Adjustment Footrest ProcedureInstalling Adjustable Angle Flip-up Footplate Flip the footplate hinge to the UP positionComposite Footplates Replacing Heel Loops FigureImpact GUARDS/CALF Strap Figure Adjusting Calfpads INSTALLING/REMOVING Elevating Legrests FigureAdjustable Footplate Release Lever Calfpad Adjust Calfpad Secure CalfpadCoved Washers Basketball Roller Locknuts Installing Basketball Roller FigureSaddle Bolts Footrest Washers Basketball Roller TubeBack Upholstery Upholstery ProcedureReplacing Seat Upholstery Figure H O L S T E R YInstalling Adjustable Tension Back Upholstery Figure AdjustingAdjustable Tension Back Upholstery Back canesH O L S T Replacing Adjustable Tension Back Upholstery FigureAdjustable Tension Straps UpholsteryWHY USE Adjustable Tension Back Guard Installing Fabric Clothing Guards FigureFabric Clothing M E Adjusting Back Height FigureProcedure Frame FOLDING/UNFOLDING Back Folding Back Wheelchairs only FigureFrame Procedure Adjusting Rear Seat Height FigureAdjusting Back Angle Folding Back Wheelchairs only Figure Back Canes With Push HandlesBack Angle to Seat Rail Arms Procedure Installing Half ARM FigureAdjusting Half ARM Height Figure Reinstall the washer and locknut onto the bottom hex screwProcedure Arms Installing the T-ARM Sockets FigureINSTALLING/REMOVING the T-ARMS Figure InstallingHeight Figure Adjusting the T-ARMSWidth Figure Depth FigureArm Clamp Arm Socket Reposition the arm tube on the T-arm postArm Sockets Figure Replacing the Locking Lever T-ARMS Figure Bottom Socket ScrewsLength Installing Flip Back Arms FigureAdjusting Flip Back Arms Figure HeightThreaded Half Clamp Installing Rigid Clothing Guards FigureGuard Slot Procedure Casters REPAIRING/REPLACING Pneumatic Caster TIRE/TUBEINSTALLING/REPLACING Front Caster Forks Figure S T E R SAdjusting Front Caster Headtubes Pro-SA Model Wheelchairs FigureRepeat Steps 1-8for the opposite side of the wheel- chair Adjusting Caster Headtube Height Pro-SA Wheelchairs OnlyRepositioning Caster Headtubes on Wheelchair Frame Figure ALL Pro Series Wheelchairs Except Pro-SA FigurePRO-SA Casters ProcedureProcedure For Repositioning the Front Caster Headtubes ALL PRO Series Wheelchairs Except PRO-SASpacer Caster Headtube Fork Stem Locknut Bolt Front Caster Installing QUICK-RELEASE Casters FigureRepeat Steps 1-4for the opposite side of the wheel- chair Rear Wheels Procedure REMOVING/INSTALLING Rear Wheels FigureAdjusting QUICK-RELEASE Axles Figure Procedure Rear Wheels Installing QUAD-RELEASE Axles FigureAdjusting QUAD-RELEASE Handles Figure And/or OutAdjusting Wheelbase Width Figure REPAIRING/REPLACING Pneumatic Rear Wheel TIRE/ TubeAdjusting Wheelbase Length Figure Removing the Play From the Rear WheelsWasher Coved Axle Washers Mounting Locknut Plate One Adjusting Rear Wheel Camber FigureJam Nuts Axle Mounting Plate Axle Bushing Wheelchair Three 3 Camber Frame WashersConditions exists TOE-IN/TOE-OUT Alignment Figures 8Rear Wheelchair Centerline Toe-out Toe-in Smaller Than Front Larger Than FrontCondition Figure REPLACING/ADJUSTING the Wheel Lock FigureCorrecting TOE-IN/TOE-OUT E E L SAdjusting the High/Undermount Wheel Lock Wheel Lock Extension Handle Installation FigureINSTALLING/ADJUSTING the ANTI-TIPPERS Figure Installing the Anti-tippersHeight Adjusting the Anti-tipper HeightAdjust Wheelchair Frame Anti-tipperHandrims Installing/Replacing Handrims Spoke Rear Wheels FigureAdjusting Handrims Spoke Rear Wheels Figure Phillips Screw HandrimLink Phillips Screw Rear Wheel HandrimComposite Rim Locknut Seat to Floor Procedure Seat to Floor Height Determination Figures 1Positioning Front Caster on the Fork Changing Seat to Floor HeightPositioning Caster Headtubes on the Wheelchair Frame Rear Seat to Floor Heights Caster Headtube Seat to Floorprocedure Front Seat to Floor Heights PRO-SA onlyPage A N T Y Limited WarrantyWarranty One Invacare Way