Panasonic WV-CP310, WV-CP314, WV-CP304, WV-CP300 operating instructions

Page 16

CP300

AUTO: Similar to the basic functions of AUTO1, but does not change the IR filter.

 

Switches to black-and-white images when brightness (illuminance) around the

 

camera is lower than approx. 0.1 lx.

 

OFF (default): Displays color images.

Note:

•CP310 When “AUTO1” or “AUTO2” is selected, it is recommended to set “AGC” to “ON”.

•If a subject is always moving or the screen is occupied with a uniform color, brightness determination may not be performed successfully because the brightness is merely deter- mined by information from the CCD image sensor. When "AUTO2" is selected, the wave length of the light source shall be 800 nm or longer.

•WV-CP300 and WV-CP304 cannot set the switching brightness (illuminance) level of color images and black-and-white images.

•To obtain color images, a sufficient level of illuminance (approx. 30 lx or more) is required.

Step 2

CP310

Press the [SET ] button.

→The "D&N (IR)" screen appears.

Step 3

CP310

 

Move the cursor to "LEVEL" and select a brightness level at which switching between color and black-and-white images is performed from the following.

LOW: Switches from color to black-and-white images when the ambient brightness (illumi- nance) of the camera is less than 0.1 lx.

HIGH (default): Switches from color to black-and-white images when the ambient brightness (illuminance) of the camera is less than 0.2 lx.

Note:

•The switching illuminance level varies with subjects, light sources, and lenses.

•The switching illuminance level varies in accordance with AGC setting. (page 12)

•The switching illuminances described above are reference values. The switching illumi- nance shall be decided based on the actual installation environment.

•There may be repeated switching between color and black-and-white images depending on the setting and environment.

Step 4 CP310

Move the cursor to "DURATION TIME" and select a time for switching between color and black-and-white images from the following.

2 S - 10 S (default) - 30 S - 60 S

(S)

(L)

 

 

Step 5

CP310

 

 

Move the cursor to "BURST (BW)", and decide whether or not to provide a burst signal output in the black-and-white mode.

ON (default): Provides a burst signal output.

OFF: Does not provide any burst signal output.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model No WV-CP310, WV-CP314 WV-CP300, WV-CP304 Preface Trademarks and registered trademarksContents About the setup menus List of setup menuBasic operation StepCamera Setup SCENE1 ALC Screen transition diagram CP310 Camera ID screenScreen transition diagram CP300 Camera title setting Camera ID Character entryCamera operation setting Camera Setup Register a scene file SCENE1/SCENE2Light quantity control method selection ALC/ELC Back light compensation functionElectronic shutter setting Shutter Gain control setting AGCElectronic sensitivity enhancement setting Sens UP White balance setting White BALManual fine adjustment of white balance Area setting screenDigital noise reduction function setting DNR Black-and-white mode settingD&N IR CP310 D&N ELE CP300CP310 VMD setting VMD Set motion detectionMotion DET screen Display Mode screen Setting of scene change detection Privacy zone setting Privacy Zone Camera system setting System Setup@ Synchronization method selection Sync Image stabilizer setting Stabilizer Electronic zoom setting EL-ZOOMUpside-down setting UPSIDE-DOWN Lens distortion correction LDCSpecial menu setting Special Setup Chroma level adjustment Chroma GainAperture level adjustment AP Gain Pedestal level adjustment PedestalCommunication setting Communication Flaw compensation PIX OFFDefault resetting Camera Reset Serial number viewing SER.NOCamera language selection Language Setup Language Setup screenSystem controller operation Setting contents Shortcut operationPanasonic Canada Inc
Top Page Image Contents