Kenmore 625.39356, 625.38356 owner manual Assemble Inlet Outlet ADAPTORS, or Single Bypass Valve

Page 11

ASSEMBLE INLET OUTLET ADAPTORS, OR SINGLE BYPASS VALVE

Complete the following steps to assemble the adaptors or bypass valve.

1.Close the shutoff valve on the house main water pipe, near the water meter or pressure tank, to turn off the water. See Fig. 7.

2.Shut off the gas or electric supply to the water heater. See Fig. 7.

3.Open the highest and lowest water faucets in your

house. This will let water drain from the pipes. Close faucets after water has drained.

4.Remove the main cover. See Fig. 8. Pull outward on two (2) tabs to release.

The salt hole cover remains attached to the main cover

when removed. Set both covers aside so they will not get scratched or broken.

INSTALL SEARS BYPASS VALVE AND / OR THE INLET OUTLET THREADED ADAPTORS

NOTE: If you will not install the bypass valve because you will have a three (3) valve bypass, skip steps 6 & 7, but do steps 5 and 8.

5.Visually check and remove any foreign materials from the valve inlet and outlet ports. See Fig. 9. Carefully remove the two large plastic clips (you will use them). Check to be sure the turbine and turbine support are firmly in place. See Fig. 10.

BYPASS VALVE:

6.Put a light coating of silicone grease on the o-ring seals and slide onto the bypass valve.

7.Push the bypass valve into the softener valve as far as it will go. Snap the two large holding clips into place, from the top down as shown. See Fig. 11.

CAUTION: Be sure the clips snap firmly into place so the bypass valve will not pull out. See Fig. 11.

INLET AND OUTLET THREADED ADAPTORS:

8.Put a light coating of silicone grease on the o-ring seals and slide into the threaded adaptors. Push the adaptors into the valve inlet and outlet ports, or bypass valve ports, as far as they will go. Both adaptors are the same and fit either port. Snap the two large holding clips into place, as shown. See Fig. 11.

CAUTION: Be sure the clips snap firmly into place so the tubes will not pull out. See Fig. 11.

Shutoff	Shutoff	. Pressure
Valve	Valve	L/Tank
	Valve	L/Tank

Pump

Electrical

Panel

FIG. 7

Salt Hole Cover

Cover (Main)

FIG. 8

INSTALLING BYPASS VALVE, AND/OR

INLET AND OUTLET THREADED ADAPTORS

Valve Outlet

Included with

Softener

Valve Inlet	Included	with
	Softener

FIG. 9

Questions? Call The Kenmore Water Line 1-800-426-9345

11

Image 11

Contents Save this Manual Repair or Parts ? Call toll freeDisclaimer of implied warranties limitation of remedies ONE Year Limited Warranty on Water SoftenerTEN Year Limited Warranty Against Leaks Questions? Page Small Parts InspectshipmentParts Descriptions Pipe Proper Order to Install Water Treating EquipmentPlan Your Installation Tools NeededValve Where to Install the Water Softener Draw Your Pipes Fittings Suggested Slab Foundation InstallationDip Adding a pressure reducing valve may reduce the flow Before Installing Checks & TestsInlet and Outlet Threaded Adaptors Assemble Inlet Outlet ADAPTORS, or Single Bypass ValveBypass Valve Bypass Valve Turned Downward Installing HoldingValve Bypass ClipsConnect the Softener Position Softener Into PlaceIII Connect the Valve Drain HoseConnect Salt Tank Overflow Tubing Leak Test House Main Water Shutoff ValvesCold Water Pipe Grounding Installgroundingclampbetween Thesoftenerinand OUT PipesWater Meter Jumper Wire Connecting TransformerRestart the Water Heater InstallcoversProgram the Timer Shows, refer to the Troubleshooting SectionSET Regeneration Time SET Presenttime of DAYSET Water Hardness Number Hardness NumberSanitize Your Water Softener AS Follows Sanitize the Water SoftenerRemoving Additives Addingsalttothe StoragetankWater Softening Salt with Iron Has Salt been added to Salt tank? Unit been sanitized? See Check List of STEP-BY-STEP Guides to InstallRecharge NOW ExtrarechargeCalifornia Efficiency Requirement Optional Settings Salt Efficiency12 / 24 Hour Clock Water Flow Through the Softener Program Memory Recharge Time Remaining and Valve Position IndicatorsError Code Kenmores Ultra Cleansing FeatureRegeneration Soft Water Service and RegenerationService Water Flow Through Softener in Backwash Water Flow Through Softener Brining and Brine RinseElectronics Soft Water Service and Regeneration Automatic BypassWater Flow Through Softener Fast Rinse Salt Bridge Salt BridgeIron from Resin BED Keeping the Water Softener Clean Nozzle & VenturiCleaning Nozzle & Venturi Protect the Water Softener from Freezing Drain ALL Water from SoftenerCorrection ProblemcauseChecklist to Help YOU Save Money Inches Model 38356 Timer Code S Model 39356 Timer Code SBypass Valves Flow Rate GPM Pressure Drop PSI vs. Flow Rate GPMEration Check Always Make These Initial Checks FirstCode Most Likely Possible ProblemProcedure for Removing Error Code From Faceplate Manual Initiated Electronics DiagnosticsModel Troubleshooting Valve Position IndicatorsTimer PWA Replacement Other InformationCycle Flow Rates Gallons PER MIN Checks, and the manual initiated diagnosticsBrine Valve Float Setting Manualadvanceregeneration CheckTo Relieve Pressure Rotary Valve ServiceDisassembly AssemblyBrining and Brine Rinse Cycle Valve Service CycleWater Flow Through the Softener Fill CycleFast Rinse Cycle Valve Backwash CycleFast Rinse Cycle Backwash CycleRating Decal Location Part Number Part Description Water Softener CompleteINLET-OUTLET Grounding Clamps Brine Valve Assembly 4212 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home

Related manuals

Manual 48 pages 28.32 Kb