Kenmore 625.39356, 625.38356 owner manual Position Softener Into Place, Connect the Softener

Page 13

POSITION SOFTENER INTO PLACE

Complete the following steps to position the softener.

1.Grip under the ridge on the salt tank sidewall.

2.Carefully rock back and forth into position.

3.Move the softener into position.

4.Place on a level and smooth surface. If needed, put a piece of 3/4" plywood, at least 17" x 20", under the tank. Then put spacers under the plywood to level the softener. See Fig. 14.

NOTE: Do not put shims or spacers directly under the tank, without the plywood. The weight of the sof- tener, when full of salt and water, may cause the tank to puncture or break at the shim or spacer.

MOVE SOFTENER INTO PLACE

Grip under ridge to move softener.

CONNECT THE SOFTENER

Refer to your plan drawing. See Fig. 5.

Measure, cut (thread if needed) and put all pipe and fit- tings together up to the main water pipe, or to the bypass valve(s) you installed in the previous step.

CAUTION: Never solder fittings while connected to nonmetallic parts. Wait until soldered pipe has cooled before connection. See Fig. 15.

CAUTION: Be careful when putting pipe fittings

together. Do not cross thread, and do not overtight- en.

Plywo_Shims

FIG. 14

TYPICAL SOLDERING

CONNECTIONS

ain Water Pipe

4.Solder

NOTE: To be certain heat will not travel down the pipe and into the bypass valve (or installation adaptors), wrap the bottom of the pipe and the bypass valve in a wet rag.

Hard Water

1.Cut pipe to correct length.

2.Solder (WHEN COOL, do Step 3).

3.Put threaded adaptor

into bypass valve port.

FIG. 15

Questions? Call The Kenmore Water Line 1-800-426-9345

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Save this Manual Repair or Parts ? Call toll freeTEN Year Limited Warranty Against Leaks ONE Year Limited Warranty on Water SoftenerDisclaimer of implied warranties limitation of remedies Questions? Page Parts Descriptions InspectshipmentSmall Parts Plan Your Installation Proper Order to Install Water Treating EquipmentTools Needed PipeValve Where to Install the Water SoftenerDraw Your Pipes Fittings Suggested Slab Foundation InstallationDip Adding a pressure reducing valve may reduce the flow Before Installing Checks & TestsBypass Valve Assemble Inlet Outlet ADAPTORS, or Single Bypass ValveInlet and Outlet Threaded Adaptors Valve Bypass Installing HoldingClips Bypass Valve Turned DownwardConnect the Softener Position Softener Into PlaceConnect Salt Tank Overflow Tubing Connect the Valve Drain HoseIII Leak Test House Main Water Shutoff ValvesWater Meter Jumper Wire Installgroundingclampbetween Thesoftenerinand OUT PipesConnecting Transformer Cold Water Pipe GroundingProgram the Timer InstallcoversShows, refer to the Troubleshooting Section Restart the Water HeaterSET Water Hardness Number SET Presenttime of DAYHardness Number SET Regeneration TimeSanitize Your Water Softener AS Follows Sanitize the Water SoftenerWater Softening Salt with Iron Addingsalttothe StoragetankRemoving Additives Has Salt been added to Salt tank? Unit been sanitized? See Check List of STEP-BY-STEP Guides to InstallRecharge NOW Extrarecharge12 / 24 Hour Clock Optional Settings Salt EfficiencyCalifornia Efficiency Requirement Water Flow Through the Softener Error Code Recharge Time Remaining and Valve Position IndicatorsKenmores Ultra Cleansing Feature Program MemoryService Soft Water Service and RegenerationRegeneration Water Flow Through Softener in Backwash Water Flow Through Softener Brining and Brine RinseWater Flow Through Softener Fast Rinse Soft Water Service and Regeneration Automatic BypassElectronics Salt Bridge Salt BridgeCleaning Nozzle & Venturi Keeping the Water Softener Clean Nozzle & VenturiIron from Resin BED Protect the Water Softener from Freezing Drain ALL Water from SoftenerChecklist to Help YOU Save Money ProblemcauseCorrection Bypass Valves Model 38356 Timer Code S Model 39356 Timer Code SInches Flow Rate GPM Pressure Drop PSI vs. Flow Rate GPMEration Check Always Make These Initial Checks FirstProcedure for Removing Error Code From Faceplate Possible ProblemManual Initiated Electronics Diagnostics Code Most LikelyTimer PWA Replacement Troubleshooting Valve Position IndicatorsOther Information ModelBrine Valve Float Setting Checks, and the manual initiated diagnosticsManualadvanceregeneration Check Cycle Flow Rates Gallons PER MINDisassembly Rotary Valve ServiceAssembly To Relieve PressureWater Flow Through the Softener Valve Service CycleFill Cycle Brining and Brine Rinse CycleFast Rinse Cycle Valve Backwash CycleBackwash Cycle Fast Rinse CycleRating Decal Location Part Number Part Description Water Softener CompleteINLET-OUTLET Grounding Clamps Brine Valve Assembly 4212 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home
Related manuals
Manual 48 pages 28.32 Kb

625.39356, 625.38356 specifications

The Kenmore 625.38356 and 625.39356 models are part of the renowned Kenmore brand, which has built a solid reputation for household appliances over the years. These models are particularly noted for their efficiency, durability, and range of features that cater to the needs of modern households.

One of the standout features of the Kenmore 625.38356 and 625.39356 is their advanced filtration system. Both models come equipped with a multi-stage filtration process that effectively captures allergens, dust, and other particulates from the air. This ensures that you breathe clean air in your home, making these models an excellent choice for allergy sufferers. The HEPA filter included in the design enhances air quality further and is easy to replace.

In terms of performance, both units boast powerful suction capabilities. The powerful motor guarantees effective cleaning across various surfaces, including carpets, hardwood floors, and upholstery. The adjustable height feature allows users to switch between carpet and hard floor settings with ease, providing effective cleaning regardless of the surface type.

Another notable technology integrated into these models is their intelligent sensor technology. This innovation detects the type of debris present and adjusts suction power accordingly, ensuring optimal cleaning performance while also conserving energy. This smart feature aids in extending the lifespan of the vacuum and increasing energy efficiency.

Ergonomics also play a significant role in the design of these Kenmore vacuum models. With adjustable handles and lightweight construction, users can maneuver them easily around their homes. The corded design provides unlimited runtime, eliminating concerns of battery life that can affect cordless models.

Additionally, the Kenmore 625.38356 and 625.39356 feature a variety of attachments designed to enhance versatility. These include crevice tools, dusting brushes, and upholstery attachments. These tools make it easier to clean tight spaces, delicate surfaces, and innovative designs that allow for a thorough clean in every nook and cranny of your home.

Noise levels in these models are also commendably low, making them a quieter option compared to many competitors. This feature allows for comfortable cleaning without disturbing family members or pets.

In summary, the Kenmore 625.38356 and 625.39356 represent a blend of advanced technology, user-friendly design, and powerful performance. Their smart features, superior filtration systems, and effective cleaning mechanisms make them an ideal choice for anyone seeking reliable home cleaning solutions.
Top Page Image Contents