Kenmore 625.39356 Recharge Time Remaining and Valve Position Indicators, Program Memory

Page 25

RECHARGE TIME REMAINING AND VALVE

POSITION INDICATORS

One of the valve position indicators (Serv, Fill, Brine, Bkwsh, Rinse) is displayed while the softener is recharg- ing. RECHARGE flashes in the display and, beginning with Brine, the minutes of recharge remaining before return to service appears in place of the present time. When the valve is moving from one cycle to another, both position indicators are flashing. See Fig. 38.

PROGRAM MEMORY

If electrical power to the softener goes off, the time dis- play is blank but the face plate timer keeps the correct time for about 6 hours. When electrical power comes on again, you have to reset the present time only if the dis- play is flashing. The HARDNESS and RECHARGE TIME never require resetting unless a change is desired. Even if the timer is incorrect after a long power outage, the sof- tener works as it should to keep your water soft. However, regenerations may occur at the wrong time of day until you reset the timer to the correct time of day.

ERROR CODE

An error code could appear in the face plate display if a problem occurs in the softener electronics. Turn to the Troubleshooting section to resolve the problem and/or call the Kenmore Water Line number listed below.

KENMORE'S ULTRA CLEANSING FEATURE

The ultra cleansing feature keeps larger particles of sedi- ment from entering the home's plumbing system. As water passes through the softener, the larger sediment particles are collected in the integrated basket and then rinsed to the drain before each regeneration. The ultra cleansing feature provides added protection for water using appliances by reducing the chance of larger parti- cles entering the various products valves and screens. An extra backwash will be preprogrammed into the electron- ics by the factory. This extra backwash will help keep the ultra cleansing feature screen clean.

Important: The ultra cleansing feature is not intended to replace pretreatment filtration. For problem water

applications, additional sediment filtration is recom- mended.

Sears offers a full line of dedicated sediment filtration

products.

Valve Position

 

Recharge Time

Indicators

 

/

Remaining

',,

 

 

s OFF SERV

--

--

I

I

 

_LL

II II

 

6

8_N_

I I_11_--MIN

s

8_wsH

RECHARGE

I

i

RINSE TIMEREMAINING

 

FIG. 38

FIG. 39

Ultra Cleansing Screen

//

\

/

Top Distributor

FIG. 40

Questions? Call The Kenmore Water Line 1-800-426-9345

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Save this Manual Repair or Parts ? Call toll freeTEN Year Limited Warranty Against Leaks ONE Year Limited Warranty on Water SoftenerDisclaimer of implied warranties limitation of remedies Questions? Page Parts Descriptions InspectshipmentSmall Parts Plan Your Installation Proper Order to Install Water Treating EquipmentTools Needed PipeValve Where to Install the Water SoftenerDraw Your Pipes Fittings Suggested Slab Foundation InstallationDip Adding a pressure reducing valve may reduce the flow Before Installing Checks & TestsBypass Valve Assemble Inlet Outlet ADAPTORS, or Single Bypass ValveInlet and Outlet Threaded Adaptors Valve Bypass Installing HoldingClips Bypass Valve Turned DownwardConnect the Softener Position Softener Into PlaceConnect Salt Tank Overflow Tubing Connect the Valve Drain HoseIII Leak Test House Main Water Shutoff ValvesWater Meter Jumper Wire Installgroundingclampbetween Thesoftenerinand OUT PipesConnecting Transformer Cold Water Pipe GroundingProgram the Timer InstallcoversShows, refer to the Troubleshooting Section Restart the Water HeaterSET Water Hardness Number SET Presenttime of DAYHardness Number SET Regeneration TimeSanitize Your Water Softener AS Follows Sanitize the Water SoftenerWater Softening Salt with Iron Addingsalttothe StoragetankRemoving Additives Has Salt been added to Salt tank? Unit been sanitized? See Check List of STEP-BY-STEP Guides to Install Recharge NOW Extrarecharge12 / 24 Hour Clock Optional Settings Salt EfficiencyCalifornia Efficiency Requirement Water Flow Through the Softener Error Code Recharge Time Remaining and Valve Position IndicatorsKenmores Ultra Cleansing Feature Program MemoryService Soft Water Service and RegenerationRegeneration Water Flow Through Softener in Backwash Water Flow Through Softener Brining and Brine RinseWater Flow Through Softener Fast Rinse Soft Water Service and Regeneration Automatic BypassElectronics Salt Bridge Salt BridgeCleaning Nozzle & Venturi Keeping the Water Softener Clean Nozzle & VenturiIron from Resin BED Protect the Water Softener from Freezing Drain ALL Water from SoftenerChecklist to Help YOU Save Money ProblemcauseCorrection Bypass Valves Model 38356 Timer Code S Model 39356 Timer Code SInches Flow Rate GPM Pressure Drop PSI vs. Flow Rate GPMEration Check Always Make These Initial Checks FirstProcedure for Removing Error Code From Faceplate Possible ProblemManual Initiated Electronics Diagnostics Code Most LikelyTimer PWA Replacement Troubleshooting Valve Position IndicatorsOther Information ModelBrine Valve Float Setting Checks, and the manual initiated diagnosticsManualadvanceregeneration Check Cycle Flow Rates Gallons PER MINDisassembly Rotary Valve ServiceAssembly To Relieve PressureWater Flow Through the Softener Valve Service CycleFill Cycle Brining and Brine Rinse CycleFast Rinse Cycle Valve Backwash CycleBackwash Cycle Fast Rinse CycleRating Decal Location Part Number Part Description Water Softener CompleteINLET-OUTLET Grounding Clamps Brine Valve Assembly 4212 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home
Related manuals
Manual 48 pages 28.32 Kb
Top Page Image Contents