Kenmore 625.39356, 625.38356 Troubleshooting Valve Position Indicators, Other Information, Model

Page 37

TROUBLESHOOTING

VALVE POSITION INDICATORS:

Depending on the valve position, the following indica- tors show in the display:

Indicator

Valve Position

Serv

Service

Fill

Fill

Brine

Brining/Brine Rinse

Bkwsh

Backwash

Rinse

Fast Rinse

When the valve is rotating from one cycle to another, both indicators flash. For example, if the valve is in transition between fill and brining, both Fill and Brine flash. Upon reaching brining position, Fill goes off and Brine is on steady. The time display shows the minutes of the cycle remaining.

NOTE: If the faceplate is left in a diagnostic display (or a flashing display when setting times or hard- ness), present time automatically returns if a button is not pressed within 4 minutes. To return to the diagnostic display, repeat step 1.

OTHER INFORMATION

While in this diagnostic screen, the following information is available and may be beneficial for various reasons. This information is retained by the computer from the first time electrical power is applied to the faceplate.

•Press and hold the UP button to display the number of days this faceplate has had electrical power applied.

•Press and hold the DOWN button to display the num- ber of regenerations initiated by this faceplate since the model code number was entered.

•Press the RECHARGE button to advance the valve to each position and observe the switch and position indicators to verify component operation, or to possi- bly isolate a defect.

•Press and hold the SELECT button for 3 seconds until either S 32 or S 33 shows in the display, see Fig. 56.

This code identifies the softener nominal capacity size. If the wrong number shows, the softener will operate on incorrect programming. Do the following as needed.

S 32 or S 33 does show: Press the SELECT button to return to the present time display.

To change the number: Press the UP or DOWN but-

ton until the correct code shows. Then, press the SELECT button and reset the timer.

Position markers

(Valve in service)

0

0

i

_1®

o o

FIG. 55

TIMER PWA REPLACEMENT

Be sure the valve is in service position when replacing the timer PWA (observe valve cycle indi-

cator). If after installing and programming the replace- ment timer PWA, the valve is not in service position, do the following to assure correct cycle orientation, or tim- ing, between the faceplate and valve.

Use the MANUAL ADVANCE procedures with the REGENERATION button, advance through the recharge cycles until the valve stops in service position, and RECHARGE no longer flashes in the display.

NOTE: The valve motor may automatically drive through several valve positions while searching for service. If an error code occurs, unplug the trans- former, then plug in again.

Model 38356

Model 39356

FIG. 56

Questions? Call The Kenmore Water Line 1-800-426-9345

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Save this Manual Repair or Parts ? Call toll freeTEN Year Limited Warranty Against Leaks ONE Year Limited Warranty on Water SoftenerDisclaimer of implied warranties limitation of remedies Questions? Page Parts Descriptions InspectshipmentSmall Parts Plan Your Installation Proper Order to Install Water Treating EquipmentTools Needed PipeValve Where to Install the Water SoftenerDraw Your Pipes Fittings Suggested Slab Foundation InstallationDip Adding a pressure reducing valve may reduce the flow Before Installing Checks & TestsBypass Valve Assemble Inlet Outlet ADAPTORS, or Single Bypass ValveInlet and Outlet Threaded Adaptors Valve Bypass Installing HoldingClips Bypass Valve Turned DownwardConnect the Softener Position Softener Into PlaceConnect Salt Tank Overflow Tubing Connect the Valve Drain HoseIII Leak Test House Main Water Shutoff ValvesWater Meter Jumper Wire Installgroundingclampbetween Thesoftenerinand OUT PipesConnecting Transformer Cold Water Pipe GroundingProgram the Timer InstallcoversShows, refer to the Troubleshooting Section Restart the Water HeaterSET Water Hardness Number SET Presenttime of DAYHardness Number SET Regeneration TimeSanitize Your Water Softener AS Follows Sanitize the Water SoftenerWater Softening Salt with Iron Addingsalttothe StoragetankRemoving Additives Has Salt been added to Salt tank? Unit been sanitized? See Check List of STEP-BY-STEP Guides to InstallRecharge NOW Extrarecharge12 / 24 Hour Clock Optional Settings Salt EfficiencyCalifornia Efficiency Requirement Water Flow Through the Softener Error Code Recharge Time Remaining and Valve Position IndicatorsKenmores Ultra Cleansing Feature Program MemoryService Soft Water Service and RegenerationRegeneration Water Flow Through Softener in Backwash Water Flow Through Softener Brining and Brine RinseWater Flow Through Softener Fast Rinse Soft Water Service and Regeneration Automatic BypassElectronics Salt Bridge Salt BridgeCleaning Nozzle & Venturi Keeping the Water Softener Clean Nozzle & VenturiIron from Resin BED Protect the Water Softener from Freezing Drain ALL Water from SoftenerChecklist to Help YOU Save Money ProblemcauseCorrection Bypass Valves Model 38356 Timer Code S Model 39356 Timer Code SInches Flow Rate GPM Pressure Drop PSI vs. Flow Rate GPMEration Check Always Make These Initial Checks FirstProcedure for Removing Error Code From Faceplate Possible ProblemManual Initiated Electronics Diagnostics Code Most LikelyTimer PWA Replacement Troubleshooting Valve Position IndicatorsOther Information ModelBrine Valve Float Setting Checks, and the manual initiated diagnosticsManualadvanceregeneration Check Cycle Flow Rates Gallons PER MINDisassembly Rotary Valve ServiceAssembly To Relieve PressureWater Flow Through the Softener Valve Service CycleFill Cycle Brining and Brine Rinse CycleFast Rinse Cycle Valve Backwash CycleBackwash Cycle Fast Rinse CycleRating Decal Location Part Number Part Description Water Softener CompleteINLET-OUTLET Grounding Clamps Brine Valve Assembly 4212 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home
Related manuals
Manual 48 pages 28.32 Kb

625.39356, 625.38356 specifications

The Kenmore 625.38356 and 625.39356 models are part of the renowned Kenmore brand, which has built a solid reputation for household appliances over the years. These models are particularly noted for their efficiency, durability, and range of features that cater to the needs of modern households.

One of the standout features of the Kenmore 625.38356 and 625.39356 is their advanced filtration system. Both models come equipped with a multi-stage filtration process that effectively captures allergens, dust, and other particulates from the air. This ensures that you breathe clean air in your home, making these models an excellent choice for allergy sufferers. The HEPA filter included in the design enhances air quality further and is easy to replace.

In terms of performance, both units boast powerful suction capabilities. The powerful motor guarantees effective cleaning across various surfaces, including carpets, hardwood floors, and upholstery. The adjustable height feature allows users to switch between carpet and hard floor settings with ease, providing effective cleaning regardless of the surface type.

Another notable technology integrated into these models is their intelligent sensor technology. This innovation detects the type of debris present and adjusts suction power accordingly, ensuring optimal cleaning performance while also conserving energy. This smart feature aids in extending the lifespan of the vacuum and increasing energy efficiency.

Ergonomics also play a significant role in the design of these Kenmore vacuum models. With adjustable handles and lightweight construction, users can maneuver them easily around their homes. The corded design provides unlimited runtime, eliminating concerns of battery life that can affect cordless models.

Additionally, the Kenmore 625.38356 and 625.39356 feature a variety of attachments designed to enhance versatility. These include crevice tools, dusting brushes, and upholstery attachments. These tools make it easier to clean tight spaces, delicate surfaces, and innovative designs that allow for a thorough clean in every nook and cranny of your home.

Noise levels in these models are also commendably low, making them a quieter option compared to many competitors. This feature allows for comfortable cleaning without disturbing family members or pets.

In summary, the Kenmore 625.38356 and 625.39356 represent a blend of advanced technology, user-friendly design, and powerful performance. Their smart features, superior filtration systems, and effective cleaning mechanisms make them an ideal choice for anyone seeking reliable home cleaning solutions.
Top Page Image Contents