Pelco C1487M-D operation manual Spectra II Zoom, Spectra Lite Zoom, Preset Functions

Page 25

ZOOM

NOTE: (Spectra II™

Only) On some controllers the zoom speed can be changed. Refer to the docu- mentation for your controller.

SPECTRA II™ ZOOM

The Spectra II™ dome can magnify an object up to 128 times. The dome has 16X of optical zoom and 8X of electronic (digital) zoom for 128X total zoom. The amount of zoom can be set for 16X, 32X, 64X, or 128X. Software controls the amount of zoom. Refer to the Zoom Limit section to program the zoom limits.

16X or 32X Zoom

Press the Zoom Tele button or turn the joystick clockwise to magnify an object up to 16 or 32 times. Hold the button or joystick until you have the picture you want.

64X or 128X Zoom

1.Press the Zoom Tele button or turn the joystick clockwise until the picture reaches 32X zoom.

2.Release the button or joystick.

3.Within one second, press the button or turn the joystick clockwise again until you have the picture you want.

Zoom Wide

Press the Zoom Wide button or turn the joystick counterclockwise to increase the field of view.

SPECTRA LITE™ ZOOM

The Spectra Lite™ dome can magnify an object up to 16 times (the dome has 16X of optical zoom).

Zoom Telephoto - Press and hold down the Zoom Tele button or turn the joystick clockwise until you have the picture you want.

Zoom Wide - Press the Zoom Wide button or turn the joystick counterclockwise to increase the field of view.

PRESET FUNCTIONS

NOTE: For American Dynamics controllers with only 32 presets, set switch SW1-7 on the dome drive in the ON position. When SW1-7 is ON, preset

99 becomes 32

98 becomes 31

97 becomes 30

96 becomes 29

95 becomes 28

93 becomes 26

92 becomes 25

91 becomes 24

90 becomes 23

If the limit stops are turned off (refer to the Limit Stops section), presets 23-26 can be used as regular presets.

The Spectra II™ dome is capable of going to 64 preset locations, each with a 20-character label. The presets are numbered 1-32 and 35-66. The Spectra Lite™ dome can go to 32 presets. The presets are numbered 1-32.

Refer to the documentation for your control system for programming presets.

When a preset operation is performed, the amount of error in moving to the pan and tilt position is 1/2 degree. If you command the dome to go to an undefined preset, erratic operation may result.

Presets 33 and 34 are fixed commands, meaning that you cannot program them. Preset 33 is the “flip” command, which will pan the dome drive 180 degrees from the position it is at. Preset 34 is the “pan zero” command, which will direct the dome drive to the factory- determined zero reference point.

The following presets are reserved for special functions. (An asterisk denotes

presets that apply to Spectra II only.)

Preset

Function

1

Park

1-7*

Alarms, if used

33Flip command

34Pan zero command

90-93

Limit stops

95Select camera programming menu

96Stop a scan

97-99 Activate scanning

In the following sections, sometimes a number in parentheses follows a preset. This second number is for 32-preset mode (conversion that lets Pelco’s presets work with American Dynamics controllers). If you are using an American Dynamics controller, use the number in parentheses.

Pelco Manual C1487M-D (7/99)

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Listed Contents List of Tables List of IllustrationsGeneral Important Safeguards and WarningsMeasures DE Securite Importantes Back Box IN-CEILING ModelsDome Drive Lower DomePendant Components Pendant ModelsModels DescriptionSpectra II Pendant Components Spectra II IN-CEILING ComponentsSpectra Lite Pendant Components Installation for IN-CEILING ModelsSpectra Lite IN-CEILING Components Ceiling and Back BOX PreparationSuspended Ceiling Installing Back BoxWiring Diagram for Spectra WiringRG6/U Cable Type Maximum DistanceTable B VAC Wiring Distances Back BOX InstallationBack BOX Connections From controller To 4-Wire terminal on circuit boardSpectra II Only The maxi Dome Drive Switch Locations Table C. Switch Settings for SW1For D-type control systems, refer to Table E Baud Rate Switch Setting SW2-6 SW2-7 SW2-8For P-type control systems, refer to Table D 100 117 177 Lower Dome Lower Dome Installation, In-Ceiling ModelsPENDANT-MOUNT Installation Installation for Pendant ModelsOperation SURFACE-MOUNT InstallationPAN and Tilt Functions POWER-UP DisplayAuto Flip Scan SpeedZoom Preset FunctionsSpectra II Zoom Spectra Lite ZoomRANDOM, FRAME, and Auto Scanning AlarmsZones PatternsPark Auxiliary OutputsWhite bal hue Spectra Lite only Prev to first camera submenu Programming the Spectra II and Spectra LiteBacklight Compensation Main Menu AccessZoom Limit Reset CameraDenotes items that apply to the Spectra II only GAIN/AGC AGC ModeAuto Iris GainShutter Speed Sharpness AUTO-FOCUS ModeLine Synchronization White Balance Color Cameras onlyPOWER-UP Mode Alarm Resume AUX ModeAlarm Priority Alarm DwellZone Blank Alarm PatternProportional PAN Turning Limit Stops On or Off Limit StopsPattern Length Park Time MinutesSymptom Unit does not operate TroubleshootingSymptom Alarms not going to preset Symptom Fan does not operateSymptom Alarms not starting a pattern Symptom Motion problemsBack BOX Electronic Assembly Removal MaintenanceDome Cleaning Mechanical SpecificationsSD5 Series Dimension Drawing Ntsc EIA Regulatory Notices Warranty and Return Information
Top Page Image Contents