Pelco C1487M-D operation manual AUTO-FOCUS Mode, Sharpness

Page 34

AUTO-FOCUS MODE

There are two auto-focus modes: auto and off.

If auto focus is in the auto mode, pressing the Focus Far or Focus Near button will place the focus in the manual mode. The dome will return to auto focus if you pan or tilt the unit or do a zoom function.

If the mode is set to off, the dome will operate in the manual mode with one exception. If you issue a command to go to a preset, auto focus will turn on and remain on until you press the Focus Far or Focus Near button.

To change the mode:

1.Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to access the main menu (refer to the Main Menu Access section). The main menu will appear.

2.If the cursor (>) is not beside Camera, move the joystick up or down to position the cursor beside Camera.

3.Press the Iris Open button to enter the Camera submenu.

4.Move the joystick up or down to position the cursor beside Next.

5.Press the Iris Open button to go to the next camera menu.

6.Move the joystick up or down to position the cursor beside Auto-Focus Mode.

7.Press the Iris Open button on your keyboard. A star will appear beside Auto-Focus Mode and the cursor will move to the right beside the word Auto or Off.

8.Move the joystick up or down to toggle between Auto and Off.

9.SELECT - Press the Iris Open button on your keyboard to select your choice. CANCEL - Press the Iris Close button if you do not want to change the setting.

SHARPNESS

There are two modes for adjusting the sharpness of the picture for Spectra II™ (automatic and manual) and one for Spectra Lite™ (manual).

To change the mode:

1.Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to access the main menu (refer to the Main Menu Access section). The main menu will appear.

2.If the cursor (>) is not beside Camera, move the joystick up or down to position the cursor beside Camera.

3.Press the Iris Open button to enter the Camera submenu.

4.Move the joystick up or down to position the cursor beside Next.

5.Press the Iris Open button to go to the next camera menu.

6.Move the joystick up or down to position the cursor beside Sharpness.

7.Press the Iris Open button. Another menu will appear with the sharpness selection(s).

8.Move the joystick up or down to position the cursor beside one of the choices. Press the Iris Open button.

34

Pelco Manual C1487M-D (7/99)

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Listed Contents List of Illustrations List of TablesGeneral Important Safeguards and WarningsMeasures DE Securite Importantes Dome Drive IN-CEILING ModelsBack Box Lower DomePendant Models Pendant ComponentsSpectra II Pendant Components DescriptionModels Spectra II IN-CEILING ComponentsSpectra Lite IN-CEILING Components Installation for IN-CEILING ModelsSpectra Lite Pendant Components Ceiling and Back BOX PreparationInstalling Back Box Suspended CeilingWiring Wiring Diagram for SpectraCable Type Maximum Distance RG6/UBack BOX Installation Table B VAC Wiring DistancesFrom controller To 4-Wire terminal on circuit board Back BOX ConnectionsSpectra II Only The maxi Switch Locations Table C. Switch Settings for SW1 Dome DriveBaud Rate Switch Setting SW2-6 SW2-7 SW2-8 For D-type control systems, refer to Table EFor P-type control systems, refer to Table D 100 117 177 Lower Dome Installation, In-Ceiling Models Lower DomeInstallation for Pendant Models PENDANT-MOUNT InstallationSURFACE-MOUNT Installation OperationAuto Flip POWER-UP DisplayPAN and Tilt Functions Scan SpeedSpectra II Zoom Preset FunctionsZoom Spectra Lite ZoomZones AlarmsRANDOM, FRAME, and Auto Scanning PatternsAuxiliary Outputs ParkProgramming the Spectra II and Spectra Lite White bal hue Spectra Lite only Prev to first camera submenuMain Menu Access Backlight CompensationZoom Limit Reset CameraDenotes items that apply to the Spectra II only AGC Mode GAIN/AGCGain Auto IrisShutter Speed AUTO-FOCUS Mode SharpnessWhite Balance Color Cameras only Line SynchronizationPOWER-UP Mode AUX Mode Alarm ResumeAlarm Dwell Alarm PriorityAlarm Pattern Zone BlankProportional PAN Limit Stops Turning Limit Stops On or OffPark Time Minutes Pattern LengthTroubleshooting Symptom Unit does not operateSymptom Alarms not starting a pattern Symptom Fan does not operateSymptom Alarms not going to preset Symptom Motion problemsBack BOX Electronic Assembly Removal MaintenanceDome Cleaning Specifications MechanicalSD5 Series Dimension Drawing Ntsc EIA Warranty and Return Information Regulatory Notices
Top Page Image Contents