Multiquip GBC Shutdown, Storage, Turn off the power switch of the generator, Attach velcro tabs

Page 23

operation

3.To turn back the lamp to its original brightness, press the dimmer switch again. The LED will turn off.

4.Tor turn off the lamp while keeping the balloon inflated, press and hold the dimmer switch for three seconds. The LED will light red.

5.Zip up the bottom of the balloon completely after use of the dimmer switch.

NOTICE

To turn on lamp again, after it was turned off with the dimmer switch, turn off the Power ON/OFF switch.Wait three to five minutes then turn the ON/OFF switch back on. The lamp will now light back to 100% brightness.

NOTICE

If the power cable is accidentally unplugged from the power source, wait three to five minutes before reconnecting the power. This will allow time for the fan to reset and ensure balloon will inflate properly when power is reconnected.

SHUTDOWN

1.Turn off the power switch of the generator.

2.Turn off the Power ON/OFF switch.The balloon should start to deflate and the lamp will turn off.

3.Disconnect the AC power cable from the generator.

STORAGE

Before storing the GBC Lighting System, perform the following steps.

NOTICE

Allow about 15 to 20 minutes for the lamp to cool down before storing the GBC. The possibility exists of the balloon getting burned if it touches a hot lamp.

1.Disconnect the lamp connector from the AC power cable.

2.Make sure the mast is completely lowered as described in LOWERING THE MAST section.

3.Unhook the AC power cable from the eyelet at the bottom of the balloon.

4.Lock the buckle to secure the balloon together.

5.Unzip the zipper on the protective cover and pull down cover over the balloon/lamp assembly.

6.Attach velcro tabs.

7.Loosen the T-bolt on the balloon/lamp assembly and lift balloon/lamp assembly from the mast.

8.Release the lever on the mast holder and pull out the mast.

9.Stow the three outriggers as detailed in the STOWING OUTRIGGER section.

gbc lighting system • operation and parts manual —rev. #0 (06/24/13) — page 23

Image 23
Contents This Manual Must Accompany the Equipment AT ALL Times Model GBCPage Page Fuel Chemical Warning GBC Lighting System Table of ContentsChoose from three easy options SaFety symBols Safety InformationSaFety messages General saFety  never unplug the lamp’s AC power cable during operation Lighting system saFetyLamp saFety  never attempt service on a running machinePower Cord/Cable safety Balloon saFetyGenerator saFety EleCtriCal saFetyCart type no lifiting hook Transporting saFetySpecifications Dimensions DimensionsIllumination Range Footcandle plot230V 50 Ft 100 Ft 200 Ft 300 Ft 400 Ft 500 Ft 600 Ft 800 Ft General informationGBC Components ComponentsAC Power Cable Connects to the AC power source Fold the balloon cover into itself and zip it up. See Figure SetupSecuring Cable with Hook Deploying outrigger OperationApplying Parking Brake Releasing Parking BrakeRaising the mast Stowing OutriggerStart the generator as indicated in the generator manual Applying PowerLowering the Mast Dimming the LampStorage Turn off the power switch of the generatorDisconnect the lamp connector from the AC power cable ShutdownRemove the lamp guard Figure MaintenanceReplacing Lamp Zip up the top and bottom of the new balloon. See Figure Replacing BalloonUnzip the top and bottom of the balloon. See Figure Locking Air Plate Filter replacementWait for lamp to cool down Loose?Lamp does not light Unplug all other appliancesC11 C10 C5 C8 Lamp Base Lamp base loose? Screw in securely Adjust Link for front shaftSpray grease Brake Not working properly? Adjust Power cable Defective or worn cable? Replace PlugWiring diagram Page Explanation of Code in Remarks Column GBC lIGHTING System 1 to 3 units Suggested Spare PartsNameplate and decals A400324600 A400324800A400324500 A400324000Balloon and lamp assy Part Name QTY Remarks Mast assy A400199700 A300175400A300175500 A300175600Base assy A300056800 A100064700A300147201 A300147301Outrigger assy A400176901 A3001622021641001430 A400175302Freight poliCy Terms and Conditions of Sale PartsPage HERE’S HOW to GET Help