Varec 4532 manual ATC specific parameter set up on the 4590 TSM

Page 38

Operating	Average Temperature/Water Bottom Sensor and Converter

7.2.2The 4532 ATC specific parameter set up on the 4590 TSM

Configuration of 4532 ATC parameters on the display of the 4590 TSM is dependent on the installed software and hardware version of the 4590 TSM. Please refer to the operating manual for the 4590 TSM to determine accessible parameters.

All required initial setup and configuration can be performed by the ToF field service tool. Detailed information will be described in the following operation related chapters.

7.3Device set up: 6000 Series Servo Tank Gauge

The 6000 Series Servo Tank Gauge is also specifically designed to recognize the 4532

ATC. Connect local HART cabling between the 4532 ATC and the 6000 Series Servo Tank

Gauge on terminals 24 and 25.

7.3.1Preparation of 6000 Series Servo Tank Gauge

The 6000 Series Servo Tank Gauge must be pre-configured to accept the 4532 ATC connection via the multi drop HART loop.

GVH362: NMT connection

"Average Temp." must be selected in order to configure the 4532 ATC.

Caution! To change this parameter, an access code is required. Please refer to the 6000

Series Servo Tank Gauge operation manual for further information.

7.3.24532 ATC configuration on 6000 Series Servo Tank Gauge

Most required 4532 ATC parameters can be configured on G4 "Temperature" matrix as it is on the display of the 6000 Series Servo Tank Gauge.

Typical 4532 ATC parameters (equivalent to the 4535 ATC) are displayed on the matrix of the 6000 Series Servo Tank Gauge.

7.3.2.1G0 Static matrix

GVH010: Liquid Temp

Calculated average liquid temperature value, determined by the 4532 ATC

GVH013: Gas Temperature

Calculated average gas phase temperature value, determined by the 4532 ATC

GVH440: Liquid Temp

The same value indicated on GVH010 Liquid Temp

GVH441: Gas Temperature

The same value indicated on GVH013 Gas Temperature

GVH442: Measured Level

Liquid level value established in the 6000 Series Servo Tank Gauge. The 4532 ATC must have liquid level data in order to calculate both liquid and gas phase average temperature.

28	Installation and Operations Manual

Image 38

Contents Installation Page Copyright Disclaimer of Warranties Safety Precaution Definitions Safety Precautions Average Temperature/Water Bottom Sensor and Converter Contents Operation and Description of Instrument Function Index Varec, Inc Contents Introduction Installation and operation overviewIntroduction Software historySystem functional diagram HartSafety instructions Grounding Power supplyWiring ReturnDirect voltage Safety instructions Scope of delivery IdentificationDevice designation Nameplate CE marks, declaration of conformity Installation Design, dimensionsRecommended procedure Incorrect procedure Flexible tube UnpackingInstallation Instructions Special conditions for safe useInstallation Mounting Mounting instructionMounting on a fixed roof tank Top anchor methodTensioning wire mounting Thermo well method Thermo well applicationAnchor weight method Flexible tube is stabilized by an anchor weightAnchor weight mounting Mounting on a floating roof tank Thermo well method Guide ring and anchor weight method 10Guide ring and anchor weight applicationMounting Wiring Terminal Connection 1 4532 ATC terminal2 6000 Series Servo Tank Gauge terminal 3 4590 TSM i.s. terminal4532 ATC Grounding Wiring Local Hart connection As a Varec tank gauging instrument Device set up 4590 TSMOperating As a standalone generic Hart instrument2 4532 ATC configuration on 6000 Series Servo Tank Gauge 4532 ATC specific parameter set up on the 4590 TSMDevice set up 6000 Series Servo Tank Gauge Preparation of 6000 Series Servo Tank GaugeGVH449 Reference GVH480 DiagnosticGVH447 Reference Zero GVH450~459 Temp No.1~10Operating Hart Device designation Temperature measurement Primary values VH00 ~ VH09Operation and Description of Instrument Function Device DataElement Temperature 1 VH10 ~ VH15 Element Temperature 2 VH20 ~ VH29Advanced Spot VH28 Lower LimitVH46 Hysteresis Width Item type read and write Default 10mm VH29 Upper LimitVH48 Gas Offset VH49 Liquid OffsetVH55 Element Volume Item type read and write Range 1 ~ WB Adjustment and Operation Power VH60 ~ VH69VH53 Element Point Item type select Default WB primary and Advanced temp VH50 ~ VH59VH72 Adjust Span Temperature Adjustment VH70 ~ VH79VH71 Zero Adjust VH69 Ref VoltageVH75 Resistance VH73 TemperatureVH74 Position VH76 Resistance AdjVH79 Protect Code VH81 Temperature Unit VH80 Present ErrorError code VH84 Distance Unit VH82 Element NumberVH83 No. of Preambles VH85 Kind of IntervalVH89 Open Error Device setting 2 VH90~VH99VH88 Short Error VH90 Device ID Number Item type read and write DefaultVH95 Manufacture ID VH92 Error Dis. SelVH94 Polling Address VH96 Software VersionRepairs MaintenanceExterior cleaning Repairs to Ex-approved devicesReplacement GVHTroubleshooting System error messagesSpare parts 1Spare PartsAnchor weight Low profile AccessoriesAnchor weight Tall profile Wire hook, Top anchor 3Wire hook dimensionTechnical data Technical data at a glanceTechnical data Order Structure Process connection SUS304Order Structure Declaration of Contamination Declaration of Contamination FormDeclaration of Contamination Form Index Index 4532 Your official representative Your offical representative