Kohler 1199250-2-A manual Product Information, Electrical Requirements, Product Notices Features

Page 2

Installation Instructions

WARNING: When using electrical products, basic precautions should always be followed, including the following:

DANGER: Risk of electric shock. Connect only to a circuit protected by a Ground-Fault Circuit-Interrupter (GFCI)*.

Building materials and wiring should be routed away from the pump body and other heat-producing components of the unit.

Install to permit access for servicing.

A pressure wire connector marked ″Earth/Ground″ is provided within the wiring compartment. To reduce the risk of electric shock, connect this connector to the grounding terminal of your electric service or supply panel with copper wire equivalent in size to the circuit conductor supplying this equipment.

Pressure wire connectors are provided on the exterior of the junction box or control within this unit to permit connection of a bonding conductor between this unit and all other exposed metal in the vicinity, as needed to comply with local requirements.

An equipment grounding terminal is provided in the field wiring compartment. To reduce the risk of electric shock, this terminal must be connected to the grounding means provided in the electric supply panel with a conductor equivalent in size to the circuit conductors supplying this equipment.

Grounding is required. The unit should be installed by a qualified service representative, and grounded.

WARNING: Risk of injury or property damage. Please read all instructions thoroughly before beginning installation, including the following requirements.

WARNING: Risk of electric shock. A qualified electrician should make all electrical connections.

WARNING: Risk of electric shock. Disconnect power before servicing.

NOTICE: Follow all local plumbing and electrical codes. In Canada, install this unit in accordance with the Canadian Electrical Code, Part 1.

*Outside North America, this device may be known as a Residual Current Device (RCD).

Product Information

Electrical Requirements

The installation must have a Class A Ground-Fault Circuit-Interrupter (GFCI) or Residual Current Device (RCD). The GFCI or RCD protects against line-to-ground shock hazards. Use a 220 - 240 V, 20 A, 50/60 Hz

dedicated service for the whirlpool.

Product Notices

WARNING: Unauthorized modification may cause unsafe operation and poor performance of the whirlpool. Do not relocate the whirlpool pump, or make other modifications to the whirlpool system, as this could adversely affect the performance and safe operation of the whirlpool. Kohler Co. shall not be liable under its warranty or otherwise for personal injury or damage caused by any such unauthorized modification.

Features

CTSeries: Components include a pump, heater, control, effervescence ports, chromatherapy lights, and illuminated keypad with remote control.

AHSeries: Components include a pump, heater, control, effervescence ports, chromatherapy lights,

1199250-2-A

2

Kohler Co.

Image 2
Contents Installation and Care Guide Electrical Requirements Product Notices FeaturesProduct Information Plus Tools and MaterialsProduct Information Prepare the Site AlcoveCut the Pump Banding Straps Install the WhirlpoolInstall the Plumbing Typical Wiring Connection for North America Make Electrical ConnectionsInstall the Whirlpool Trim Kit Important Safety Instructions Important Safety Instructions Models with Neckjets Operating InstructionsAll Models Neckjet and Backjet Operation if equipped Remote ControlOperating Instructions Effervescence Operation if EquippedFlush the System Care and CleaningWarranty Warranty For MexicoTroubleshooting Exceptions and RestrictionsTroubleshooting Symptoms Probable Causes Recommended ActionTroubleshooting Troubleshooting Installations électriques requises Information sur le produitInformation sur le produit Outils et matériauxCaractéristiques Encastrer par le dessus Préparer le siteAlcôve Couper les sangles de retenue de la pompe Installer la baignoire à hydromassageInstaller la plomberie Commande Effectuer les connexions électriquesTerminer l’installation Installer le kit de garnitureInstaller la garniture de jets pour le cou si inclus Nettoyer après l’installationInstructions Importantes sur la sécurité Instructions Importantes sur la sécurité Modèles avec jets pour le cou Instructions d’utilisationTous les modèles Fonctionnement de la chromothérapie si présente Instructions d’utilisationFonctionnement de l’option d’effervescence si présente Purger le système TélécommandeEntretien et nettoyage GarantieGarantie Limitée D’UN AN GarantieDépannage Symptômes Causes probables Action recommandée Dépannage1199250-2-A Français-15 Kohler Co Kohler Co Français-16 1199250-2-A 1199250-2-A Français-17 Kohler Co Información sobre el producto Requisitos eléctricosCaracterísticas Herramientas y materialesAvisos sobre el producto Información sobre el productoDe sobreponer Prepare el sitioEncajonado entre tres paredes Instale la plomería Instale la bañera de hidromasajeCorte las cintas metálicas que sujetan la bomba Conexión de cableado típica para Norteamérica Protección contra tirones adecuadaPruebe el funcionamiento de la bañera de hidromasaje Instale el kit de guarnición de la bañera de hidromasajeInstale el kit de guarnición Termine la instalaciónInstrucciones importantes de seguridad Instale el kit de guarnición de la bañera de hidromasajeInstrucciones importantes de seguridad Modelos con jets para el cuello Instrucciones de funcionamientoTodos los modelos Funcionamiento de la cromoterapia si está equipada Instrucciones de funcionamientoFuncionamiento del modo efervescente de estar equipado Garantía Cuidado y limpiezaLimpie el sistema Control remotoGarantía Limitada DE UN AÑO GarantíaGuía para resolver problemas Para MéxicoGuía para resolver problemas Síntomas Causas probables Acción recomendada 1199250-2-A Español-16 Kohler Co Kohler Co Español-17 1199250-2-A Kohler Co